AMPERE 010422 Shower Power User Manual
Welcome Note from the Founders
There’s really no need to remind everyone how crazy life is right now. We all need a micro-lift… some time to relax, de-stress and even have a bit of fun. Having as little as five minutes of alone time is an easy way to get back on track. For a lot of people, the time you spend in the shower may be the only truly alone time you get all day. Why not make the most of it?!
Enter… Shower Power. A patented Bluetooth speaker that generates all of its power from the water you are already using in the shower. Take a shower while jamming out to your music, listening to your favorite podcast, or relaxing to an audiobook… What’s not to like? Shower Power has transformed our daily showers and we know you are going to love using it every day too. Shower Power integrates seamlessly into your daily routine.
We designed it to be effortless to use. Installation is fast and simple. It turns on and pairs automatically. And best of all, you never have to worry about charging it. With Shower Power, you will always have a powerful fully-charged Bluetooth speaker in your shower. We guarantee that your time in the shower will never be the same.
Specs
- Battery: 1800 mAh Lithium Ion
- Frequency Range: 100hz-20Khz
- Speaker: 40mm x 2
- Speaker Power: 3W x 2
- Supports Bluetooth®: 5.1
- Weight: 520 g.
- Size: 158 x 95 x 91mm
What’s in the Box
Quick Start Guide
For more detailed installation instructions and how-to videos, go to install-shower-power.ampere.shop or scan the QR code below.
Before you begin, identify your shower fitting.
Fixed
The showerhead attaches to a fitting that comes straight from the wall at an angle. The fitting is male and the showerhead is female.
Rain
The showerhead attaches to a fitting that comes straight down from the ceiling. The fitting is male and the showerhead is female. *Installation steps are the same for fixed and rain shower fittings.
Handheld
The showerhead attaches to a hose that comes from a fitting lower down on the wall. The hose is female and the showerhead is male.
*Tip
You can install Shower Power on either end depending on your preference. It can be at the base of the hose OR at the end of the hose, attached to the showerhead.
Unbox the Shower Power and remove the speaker from the dock
Rotate the speaker 90 degrees counterclockwise to separate it from the dock. Set the speaker and dock aside.
Remove your showerhead from the fitting
Unscrew the showerhead. You can usually do this by hand but may need a pair of pliers if it was installed too tightly.
Install the male-male connector on the appropriate side
Shower Power is not bidirectional so it is critical to determine which side of Shower Power is input and which side is output. There is a sticker that indicates the input side (this can be removed after the first use). For additional confirmation and future checks, the hole on the input side is smaller. As such, the turbine will be more visible on the output side. In addition, there is a small metal sensor on the output side.
Rain and Fixed
For these shower types, the male-male connector will go on the output side (the side that connects to the showerhead). First, screw in the male-male connector by hand and then tighten it with the hex key.
Handheld
For these shower types, the male-male connector will go on the input side (the side that connects to the hose). First, screw in the male-male connector by hand and then tighten it with the hex key.
Connecting your showerhead to the shower dock
Attach your showerhead to the shower dock. Connect securely but don’t overtighten. If you noticed that your showerhead/fitting already used sealing tape, you may want to use it at this stage of the installation process.
Tip for handheld showers
If the showerhead is not oriented in the direction you want then you can add a rubber O-ring inside the output threads on Shower Power. Use the thinner rings for smaller adjustments and the thicker rings for larger adjustments. You can use multiple if necessary.
Connect the shower dock + showerhead to the shower fitting
Finally, connect the shower dock, with the showerhead now attached, to the shower fitting. *Tip for rain and fixed showers If the showerhead is not oriented in the direction you want then you can add a rubber O-ring inside the output threads on Shower Power. Use the thinner rings for smaller adjustments and the thicker rings for larger adjustments. You can use multiple if necessary.
Connect the speaker (aka Droplet Pro) to the shower dock
Align the bump in the underside of the shower dock with the groove on the top of the speaker (Droplet). The Ampere logo will be facing the same direction as the flow of water and you should feel the bump go into the groove. Then, rotate the speaker 90 degrees. You will feel it “lock” into place and the Ampere logo will be perfectly centered along the side of Shower Power.
Congratulations! Now you are ready to rock n’ roll
Troubleshooting
It’s leaking! What do I do?
The first thing to check is if you screwed in Shower Power tight enough. The next solution is to try adding rubber O-rings to the female ends of the connection. Another solution is to use the included thread-sealing tape to make the connection tighter. Wrap the sealing tape around the threads in a counterclockwise direction for a better seal.
What do I do if the Shower Power is not pointed in the direction I want?
If the showerhead is not oriented in the direction you want then you can add a rubber O-ring inside the output threads on Shower Power. Use the thinner rings for smaller adjustments and the thicker rings for larger adjustments. You can use multiple if necessary. You can also use the included thread sealing tape to prevent leakage and screw to your preferred direction.
Using Shower Power
Hydroelectric Charging:
Charging a Bluetooth speaker has never been easier–all you have to do is take a shower. Shower Power will charge whenever there is flowing water. Under “normal use conditions,” Shower Power will never need to be charged. We consider “normal use conditions” to be water pressure between 30-50 PSI, water temperature of less than 120°F (50°C), and only using Shower Power while the water is running. If you use Shower Power without water running, then you will be using the reserve battery power. Continued use will result in needing to use the USB-C port to charge the Shower Power.
USB-C Charging:
Remove the Droplet (the speaker) from the Shower Dock and make sure it is completely dry before plugging in. You can charge a Droplet with almost any adapter from a reputable brand. The droplet is compatible with QC and PD adapters.
Low Power Notifications:
When the battery level reaches 20% Shower Power will beep three times. Alternatively, you can use the USB-C port to bring it back up to 100%.
Pairing
When the Shower Power is turned on, it will enter Bluetooth pairing mode automatically. The “searching sound” will play for one minute but it will remain in pairing mode for three minutes. If no device is paired within three minutes, Shower Power will automatically turn off. To pair your device, open the Bluetooth pairing tab on your device and select “Shower Power.” Play your favorite audio from your device. You can pause, play, skip, change volume, etc from your device, via the button pad, or the Shower Power remote control.
Button Pad
Power Button
- Hold for two seconds to turn the Shower Power on and off.
- The power button will illuminate green when the battery is charging.
- The power button will blink blue while in pairing mode.
Play Button
- Single press to pause and play your audio.
- Hold for two seconds to skip to the next song.
Pairing Button
- Single press to enter TWS pairing mode.
- Press and hold for 2 seconds to enter Bluetooth pairing mode.
- Hold for 10 seconds to clear the Bluetooth pairing history.
+/- Buttons
- Single press the + and – buttons to increase and decrease volume, respectively, one level at a time.
- Hold the + and – buttons to “scroll” through the volume levels more quickly.
Shower Power Accessories
Droplet/Droplet Pro
When sold with the Shower Dock, the speaker and Shower Dock together are called Shower Power (and Shower Power Pro). When purchased separately, the speaker component is referred to as Droplet (and Droplet Pro). Regardless of whether you bought the speaker component as part of “Shower Power” or separately, it will work with any Shower Power Shower Dock.
TWS Pairing
Before pairing your device, turn on two Ampere speakers (Droplet, Droplet Pro, Shower Power, Shower Power Pro) and allow the two speakers to connect. When they connect successfully, you’ll hear a pairing sound. Single press the pairing button to enter TWS pairing mode. After two speakers are connected, press one to disconnect it. After disconnecting the TWS, if you would like to repair it, turn the Droplet off and turn it on again.
Shower Power Remote
The Shower Power remote works just like the button pad on the Shower Power itself. If it’s hard to reach, the remote allows you to control all the functionality from up to 5 meters away. The only difference is that the power button on the remote does not turn Shower Power on. Shower Power will turn on automatically when water starts to flow.
Cleaning and Care
Just like any showerhead, over time, the Shower Dock may become stained or dirty. This could be a buildup of limescale, metals and minerals (like iron and manganese), or bacteria. It is fine to clean the Shower Dock with the same cleaners that you use for your showerhead. That could include vinegar, baking soda, or gentle bathroom cleaning spray. Before you begin, remove the speaker (Droplet) from the speaker dock and set it aside.
When cleaning the shower dock, pay close attention when cleaning the inside so as not to damage the pogo pins. Be very careful with any cleaning agents around the pogo pins and try to keep them as dry as possible. To clean the speaker component (Droplet), remove it from the speaker dock and clean it with a damp cloth. Do not leave the pogo pin connection wet or submerged in water.
Warnings
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 20mm must be maintained between the user’s body and the handset, including the antenna. Third-party belt clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or approved antenna. This device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. All essential radio test suites have been carried out.
CAUTION :
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS The product shall only be connected to a USB interface of version USB 2.0 Adapter shall be installed near the equipment and shall be easily accessible. The plug is considered as the disconnect device of the adapter The device complies with RF specifications when the device is used at 20mm from your body.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. f this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum distance between 20cm of the radiator and your body: Use only the supplied antenna. This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
Like Shower Power?
Check out the rest of the Ampere product line at Ampere. shop. Shop innovative tech products from chargers, cables, and power banks to one-of-a-kind products like Dusk and Side Pocket. To get a $20 gift card to Ampere. shop, register your Shower Power now. To register your warranty, text “Shower Power” to +1 617 906-7774 or visit register.ampere.shop or scan here.
