Magic Chef 12000 BTU Air Conditioner Portable For Room User Guide

Magic Chef 12000 BTU Air Conditioner Portable For Room User Guide

Product Registration

Thank you for purchasing a Master Craft® product. The first step to protect your new product is to complete the product registration on our website: www.mcappliance.com/register. The benefits of registering your product include the following:

1. Registering your product will allow us to contact you regarding a safety notification or product update.
2.  Registering your product will allow for more efficient warranty service processing when warranty service is
   required.
3.  Registering your product could act as your proof of purchase in the event of insurance loss.

IMPORTANT SAFETY INSTRUCTIONS

1. Place the unit on a level, sturdy section of the floor, away from heat sources or anywhere it could get wet.
2. DO NOT stand, sit, or place anything on top of the unit.
3.  DO NOT let children operate or play on or around the air conditioner.
4.  The power cord is equipped with a 3-prong grounding plug to protect against shock hazards. ALWAYS plug cord into a properly installed and grounded 3-prong wall receptacle. Refer to the manufactures rating label for electrical and other technical data specific to this unit.
5.  DO NOT modify or cut the power cord, or use any other cord or plug. Contact customer service or a qualified service technician for replacement or repair.
6.  DO NOT run cord under carpeting, throw rugs, runners, or similar coverings. DO NOT route cord under furniture, appliances, or any heavy object.
7.  DO NOT start or stop the unit by turning the power on or off.
8. DO NOT insert or pull out the plug with wet hands.

SPECIFICATIONS

Parts Identification

a.Control Panel
b. Horizontal Louver Blade
c. Panel
d. Caster
e. Upper Air Filter (behind the grille)
f. Handle (both sides)
g. Upper Air Intake
h. Drain Outlet
i. Air Outlet
j. Power Plug Socket
k. Power Cord Outlet
l. Lower Air Filter (behind the grille)
m. Lower Air Intake
n. Power Cord Buckle
o. Bottom Tray Drain Outlet
p. Remote Control

Installation Instructions

Tools Needed

• Medium Philips screwdriver
•  Tape measure or ruler
• Knife or scissors
•  Saw (optional, to shorten window adaptor for narrow windows)

Accessories
Your Window Installation Kit fits hung or sliding windows 26.5-48” (67.5-123cm) and can be shortened for
smaller windows.

LOCATION
Your installation location should meet the following requirements:

• Make sure that you install your unit on a level surface to minimize noise and vibration.
• The unit must be installed near a grounded plug, and the Collection Tray Drain (found on the back of the unit) must be accessible.
• The unit should be located at least 12” (30cm) from the nearest wall to ensure proper air conditioning.
•  DO NOT cover the Intakes, Outlets or Remote Signal Receptor of the unit, as this could cause damage to the unit.

WINDOW INSTALLATION KIT

1. Preparing the Exhaust Hose Assembly: Press the exhaust hose into the window slider adaptor and unit adaptor and clamp with the buckles of the adaptor.
2.  Attach the Exhaust Hose Assembly to the Unit: Align the hook on the Unit Adaptor with the Hole Seat on the back of the unit and insert into lower groove, then attach Hook to the Hole Seat.
3.  Prepare the Adjustable Window Slider: Measure the size of your window opening. If needed, cut the window slider to the correct length. You may need both window sliders, in which case, slide Window Slider B into Window Slider A, adjust to correct size, and use the bolt to fasten the window sliders together.

REMOTE CONTROL

Before you begin using your new air conditioner, make sure to familiarize yourself with the remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the OPERATING INSTRUCTIONS section of this manual. For best results, make sure you are pointing the remote control at the air conditioner. The remote has a range of about 26’ (8m), and there will be a beep from the A/C unit when the remote signal is received. Anything obstructing a direct line between the remote and the unit, as well as direct sunlight, may interfere with the signal.

FUNCTION BUTTONS

• Button designs on your unit may differ slightly from the example shown. If the unit does not have a particular function, pressing that function button on the remote control will have no effect.
•  See OPERATING INSTRUCTIONS section for more detailed information on the functions controlled by the remote control.

a. ON/OFF: Turns the unit on and off.
b. MODE: Cycles through the modes
c. FAN: Changes the fan speed
d. SLEEP: Starts the sleep mode
e. SWING: Starts and stops louvers
f. TEMP: Adjusts temperature up or down. Pressing up and down arrows together for 3 sec will change display from F to C.
g. SHORT CUT: Sets and activates pre-sets

• •  Used to save the current settings or resume previous settings.
  •  Push for more than 2 seconds, the system will automatically save the current operation settings including
    operating mode, setting temperature, fan speed level and sleep feature (if activated ).
  • Push this button when unit is on and the system will automatically restore the saved settings
    including operating mode, setting temperature, fan speed level and sleep feature (if activated).

h. TIMER ON/OFF: Sets timer to turn unit on or off.
i. LED: Turns units LED Display on or off.

REMOTE CONTROL DISPLAY

a. Transmission Indicator: Lights up when remote sends signal to unit.
b. ON/OFF Display: Appears when the unit is turned on, and disappears when it is turned off.
c. TIMER ON Display: Displays when TIMER ON is set.
d.TIMER OFF Display: Displays when TIMER OFF is set.
e. Mode Display: Displays the mode “AUTO” – “COOL” – “DRY” – “HEAT” – “FAN”.
f. Battery Display: Low Battery detection
g. Sleep Display: Displays when Sleep function is activated.
h. Fan Speed Display: Displays selected Fan Speed “>>>>>>>>>>” (HIGH) – “>>>>>>>” (MED) – “>>>” (LOW). This display is blank when set to AUTO speed.

INSERTING AND REPLACING BATTERIES

Your remote uses two AAA batteries. To install or replace batteries:

1.  Slide the cover on the back of the remote downward, exposing the battery compartment.
2.  Insert the batteries, making sure the (+) and (-) ends of the batteries match the symbols inside the battery compartment.
3.  Slide the battery cover back into place.

NOTE: For optimum performance, do not mix old and new batteries. It is recommended to remove the batteries if the remote will not be used for more than 2 months. Always be sure to properly dispose of old batteries. The device complies with the local national regulations. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.
   This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

• Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.

CARE AND MAINTENANCE

WARNING: Turn the unit off and remove the plug from the wall outlet before maintenance or cleaning.

•  DO NOT use flammable liquids or chemicals to clean the unit.
• DO NOT immerse in or spray with water to clean.
• DO NOT operate the unit if the power cord is damaged.
•  The water bucket should be cleaned every few weeks or as needed. DO NOT leave water in the bucket when unit is not being used. ALWAYS empty before storage or as soon as “P1” is displayed.

Clean the Air Filters

• Clean the air filters with water at least once every 2 weeks for optimal performance, or as needed. DO NOT use the unit with the filters missing.
• If used in a household with animals, periodically wipe down the grills to prevent animal fur from blocking airflow. Figure 13

Cleaning the Portable Air Conditioner

• Clean the unit using a damp, lint-free cloth and mild detergent (if needed) and dry off with a dry, lint-free cloth.

STORAGE

•  Drain the unit’s water collection tray according to the instructions.
• Run the unit on FAN mode for 12 hours in a warm room to dry it and prevent mold. Turn off the appliance and unplug it. Clean the air filter according to the instructions above. Reinstall the clean, dry filter before storing.
•  Remove the batteries from the remote control.
• Be sure to store the unit in a cool, dark place. Exposure to direct sunshine or extreme heat can shorten the lifespan of the unit.

TROUBLESHOOTING