Vaddio 9992225012 In-Wall Recessed Camera Mount User Manual
OVERVIEW:
The Vaddio IN-Wall camera mounti ng systems are an attractive way to mount PTZ camera s on a wall where room aesthetics are critical. These mounting systems use the depth of the wall cav ity to minimize the camera’s extension into the room while providing a finished look to the instal lation. Each s ystem consists of an in- wall mounting box, camera pl atform and fac e frame, which are powder coated white, but can be painted to match any décor.
IN-Wall Enclosure Supported Cameras and Part Numbers
Part Number Compatible Camera Systems
999-2225-018 Vaddio ClearVIEW™, PowerVIEW™, WallVIEW™ HD Series or RoboSHOT Series Systems
999-2225-012 Vaddio ZoomSHOT and WideSHOT Sony EVI-D70 , Vaddio WallVIEW 70 System
999-2225-014 Sony EVI-HD1, Vaddio WallVIEW CCU or PRO HD1 PTZ System, WallVIEW EagleEye 1080 HD and Polycom EagleEye 1080 HD
999-2225-015 Polycom EagleEye and EagleEye IV, Vaddio WallVIEW PRO EagleEye, Cisco PrecisionHD, Cisco PrecisionHD 1080p and LifeSize 4X
999-2225-016 Sony BRC-H700, Vaddio WallVIEW CCU or PRO H700 PTZ System
Sony BRC-Z700, BRC-H900 Vaddio WallVIEW CCU or PRO Z700 PTZ System
999-2225-011 Sony EVI-D100, Vaddio Model & WallVIEW 100 System
999-2225-019 Sony BRC-Z330, Vaddio WallVIEW CCU or PRO Z330 PTZ System, EVI-D80 EVI-D90, EVI-H100, Vaddio WallVIEW 80 & 90
999-2225-020 Cisco Precision 60
999-2225-220 LifeSize 10X PTZ
Intended Use: Please read the entire manual thoroughly. The IN-Wall Enclosure was designed, built and tested for use indoors and for a particular camera listed above. Mounting the wrong camera in t he IN-Wall may create a potentially unsafe o perating condition.
Save These Instructions: The information contained in this manual will help you install and operate your product. If these instructions are misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product drawings for the Vaddio product line on the Vadd io website. These documents can be downlo aded from www.vaddio.com free of charge.
UNPACKING:
Carefully remove the product and all of the p arts from the packaging and identify the follo wing parts:
- One (1) Back Box Enclosure
- One (1) Camera Platform
- One (1) Face Frame
- One (1) Set Mounting Hardware and Screws
- Four (4) 8-32 X ¼” White Pan Head Scre ws (for Face F r ame attachment)
- Four (4) 10-32 x ¼” Flat Head Screws (for Camera Platform attachment)
- Four (4) Self-Drilling Drywall Anchors
- Four #8 x 1.25” Screws for Wall Anchors
- One (1) ¼” x 20 Camera Mounting Screw (for those cameras that use ¼” x 20 screws) -OR-
- Four (4) M3x6mm Camera Mounting Screws for Polycom EagleEye Cameras (non-Sony)
IN-Wall Enclosures
- Deep Back Box Enclosure
The 3-15/16” deep metal wall box uses the maximum depth of a standard 2” x 4” framed wall cavity and minimizes the camera’s protrusion into the room. Each Enclosure is outfitted with three (3) conduit knockouts (2-sides, 1-top) and a cable pass-through in the back box and camera platform. - Before Installing
When locating the IN-Wall en closure, consider vie wing angles, lighting con ditions, possible line of site obstructions and check for in-wall obstructions where the camera is to be mounted (like studs). Pick a mounting location to optimize the performance of the camera. Please read the step-by-step instructions fully before starting the installation.
INSTALLATION INSTRUCTIONS:
- Position the back box enclosure against the wall, level the box and trace the outline of the box on the wall with a pencil.
- Use a level to position the enclosure and trace a line around the back of the enclosure once the box is level.
- After checking for in-wall obstructions, cut out the area ma rked on the wall with a drywall saw.
- Place the enclosure into the wall opening fo r a dry fit and mark the four holes for the spiral wall anchors through the mountin g flanges. The integrator ca n use an y wall anchor of their ch oice or use the supp lied wall anchors. Level the back box. Remove the back box and install the wall anchors. Pull the cabling through the wall and back box and pus h it into the opening. Fasten the enclosure to the wall with wall anchors.
- On the sides of the face frame, there are four holes (s ee dra wing be low) for attaching the Face Frame to the Back Box with the supplied white pan head machine screws.
- Place the Camera Platform onto the bottom of the Back Box, a nd scre w the platform down with the four flat head machine screws. If using the cable pass-through, thread the cables through the platform.
- Connect the camera system and push the slack in the cabling back into the wall.
- Place the camera on the Camera Platform and secure the camera to the platform with the supplied screws
HARDWARE WARRANTY:
Please see the Vaddio website at support.vaddio.com for the Vaddio Statement of Warranty for all Vaddio Products. The Statement of Warranty covers the policies and procedures of the Hardware Warranty, Exclusions, Customer Service, Technical Support, Return Material Authorizations (RMA), Voided W arranty, Shipping, Handlin g and Products Not Under Warrant y. The Vaddio Warranty Statement supercedes all other published warranty statements heretof ore in content and coverages . Vaddio Technical Support can be co ntacted through the Vaddio website or throu gh e-mail support at support@vaddio.com.
REFRENCE LINK
