Honeywell 6.5ft 400ct Churchill Pine Prelit Manual

Honeywell 6.5ft 400ct Churchill Pine Prelit Manual

Thank you for purchasing The 6.5ft Honeywell Churchill Pine LED One Plug tree. This tree assembles in minutes and is decorated with LED light sets. For your convenience, it is  equipped with a foot pedal switch for easy illumination.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical products, basic precautions should always be followed including the following:

• Do not use this product outdoors.
• This seasonal use product is not intended for permanent installation or use.
• Do not mount or place near gas or electric heaters, fireplace, candles or other
• Do not secure the wiring of the product with staples or nails, or place on sharp
• Do not let lamps rest on the supply cord or on any wire.
• Unplug the product when leaving the house, when retiring for the night, or if left
• This is an electric product not a toy! — To avoid risk of fire, burns, personal injury and electric shock it should not be played with or placed where small children
• Do not use this product for other than its intended use.
• Do not hang ornaments or other objects from cord, wire, or light string. Hang
• Do not close doors or windows on the product or extension cords as this may
• Do not cover the product with cloth, paper or any material not part of the product ornaments only on the tree itself.
• This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet.
• Read and follow all instructions that are on the product or provided with the product.

PACKAGE CONTENT

Installation kit:

• A. Top Section (1 set)
• B. Middle Section (1 set)
• C. Bottom Section (1 set)
• D. Tree Base (1 set)
• E. Screw  (1 set)

OTHER COMPONENTS

• F. Bolt  ( 2 PIECES )
• G. Fuse ( 2 PIECES )
• H. Replacement lamp ( 8 PIECES )

INSTALLATION

Note: Before you start to assemble your tree, please choose a location near an electrical wall outlet. Place the tree stand on a level surface.
Please remove protective covers from the base of the pole from each section.

1. . Unfold the tree base to a 90 degree angle.
2. Carefully insert bottom section (C) of tree into tree base and tighten the screw (see Fig. 1).
3. Insert the middle section (B) of the tree into the bottom section (C) (see Fig. 2).
4. Insert the top section (A) into the middle section (B) (see Fig. 3).
   Note: There is a tree top connector on the top section (A).
5. Allow the branches to fall into place or gently pull branches up and out. When adjusting branches be sure that all wires are free of branch hinges (see Fig. 4).
6. . Shape the branches. Starting with tips closest to the pole, shape one tip to the right, one to the left and one along the centre of the main stem. Repeat pattern for each branch (see Fig. 5).
7. Plug the well-connected power supply cord plug 1 from the bottom section (C) into electrical outlet. Please note this tree comes with an on/off foot pedal switch for easy illumination. The plug 2 is for tree top lights. Plug the power supply cord plug 2 into electrical outlet.

TROUBLESHOOTHING

If any lights do not work on your pre-lit tree, please check the following before calling customer service:

1. If entire tree or a section of the tree does not light:
   a) Make sure the end connector of the power cord is well connected to the
   c) Check that there is power at the electrical outlet.
   d) Check fuses in tree’s plugs and replace if necessary (see Replace the fuse below).
2. If a strand of lights still does not work:
   a) Check that all lamps are tightly fitted inside the lamp holders and that no lamps are broken or missing. Replace any broken or missing lamps with replacement lamps provided.
3. . If you are still experiencing problems with the tree, please contact us at 866-205-9854

Loose branches

If a branch of the tree falls off, follow the steps below to reinstall it with a spare bolt.

1. Place the branch into the slot of the bracket.
2. Insert a spare bolt through the hole and use diagonal pliers (not included) to crimp the bolt. (See Fig. A)

Replace the lamp

1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug
2. Unlock the burned out LED lamp by lifting the hook.
3. Pull lamp and plastic base straight out of lamp holder.
4. Replace lamp with only 3.0 Volt, 0.06 Watt, LED type lamp (provided with
5. Lock the hook of lamp base by pushing lock down into the tab.

CAUTION

1. To reduce the risk of overheating, replace burned-out lamps promptly. Use 3.0 Volt, 0.06 Watt LED lamps only. The LED lamp has polarity. Do not deliberately change the direction of the LED lamp in the lamp holder.
2. Risk of fire. This product does not contain lamp shunts, which allow the product to operate if one lamp burns out. Replace lamps only with the spare lamps provided with this product.If the new lamp base does not fit in lamp holder, follow the steps below before step 4:
   a) Pull the reflector out.
   B) Remove the base of burned out lamp by straightening lamp leads and gently
   c) Thread leads of new lamp through holes in old base with one lead in
   d) After lamp is fully inserted into base, bend each lead up, like other lamps in the light set so that the leads will touch the contacts inside the lamp holder (always match the long lead of new lamp to the hook of lamp base).
   e) Insert the reflector into the base.

USE AND CARE INSTRUCTIONS

• a) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lampholders or enclosures,
• b) When storing the product, carefully remove the product from wherever it is placed loose connections, or exposed copper wire.
  to avoid any undue strain or stress on the product conductors, connections, and wires.
• c) When not in use, store neatly in a cool, dry location protected from sunlight.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.

Warning: Please note that changes or modifications of this product is not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

UL MODEL NO. TME6.5-6(0.2)

STORAGE

Disassembled tree can be stored in its original box. Store tree in a cool, dry place where the temperature does not exceed 100°F (38°C).
ONE PLUG® U.S. Patents: US8,454,186, US8,454,187, US8,936,379, US9,140,438, US 9,157,588, US 9,179,793, US9,243,788, US 10,194,764, US 10,433,604, US 10,578,289, US 10,721,981, US 11,006,687. Other Patents Pending.

See www.williscorporation.com/about.html #p6 for a complete list of patents.

ARCHWAY MARKETING SERVICES
DEPT. 4599, CAROL STREAM, IL 60122-4599 866-205-9854

REFERENCE LINK

https://www.honeywellstore.com/store/category/honeywell-christmas-trees.htm

https://www.honeywellstore.com/store/images/pdf/W14L0685-honeywell-christmas-tree-manual.pdf