Garmin Bark limiter Series Owner Manual

Garmin Bark limiter Series Owner Manual

Device Overviews

Attaching the Dog Collar Device to the Collar Strap1

1. With the buckle facing outward, insert the end of the collar strap through the slot on the collar device.

1. Pull approximately two-thirds of the collar strap through the slot.
2. Insert the end of the collar strap through the slot
3. Pull the strap until it is tight across the front of the device.

Charging the BarkLimiter Deluxe Device

NOTICE
To prevent corrosion, thoroughly dry the contacts on the collar and the surrounding area before connecting the charging clip.Before you put the collar on the dog, remove the charging clip. If you do not remove the clip, it may become detached from the collar and become lost.

1.  Snap the charging clip onto the device.
2. Plug the small end of the power cable into the mini-USB port on the charging clip.
3.  Plug the other end of the power cable into a power source.The status LED is solid red when the collar is charging.
4.  After the status LED turns solid green, remove the charging clip from the collar.

Bark Correction

When the device is active and properly fitted on the dog, it detects and corrects barks automatically. You can adjust the method and intensity of the corrections.The status LED flashes briefly when the device detects motion or corrects a bark.

Troubleshooting

My device does not seem to be active When the device is active, the status LED flashes only when the device detects a bark or motion.

• Verify the collar is turned on (page 1).
• Verify the battery is not low (page 3).
• Remove the device from the dog, and shake the device briefly.

When the device is active, the device detects the motion, and the status LED flashes.

Specification

BarkLimiter Specifications

BarkLimiter Deluxe Specifications

Sleep Mode
To conserve battery life, the device goes into sleep mode when no barks or motion are detected. The activity level of your dog affects the battery life of the device.

Checking the Battery Charge Level
Rotate the dial away from N.The color of the status LED indicates the battery charge level for five seconds.

BarkLimiter Components

Replacing the BarkLimiter Battery

Before you replace the battery, you must remove all dirt, water, and debris from the device. You also need a small Phillips screwdriver.

You must replace the battery with a 3V CR2 lithium battery.

• Remove the four screws from the corners of the back
• Remove the back

The battery comes out with the back plate.

• Remove the
• Install the new battery into the back plate according to the polarity indicators engraved on the back

When properly installed, the battery snaps into the back plate.

• Verify that the gasket is not damaged and that it is completely seated in the
• Replace the back

Replace the four screws to secure the back plate.

BarkLimiter Deluxe Components

Fitting the Collar on Your Dog

CAUTION

To prevent irritation from the contact points, remove the collar for at least eight hours out of every 24-hour period. This device is not intended for human use. Do not attempt to use on any person.

NOTICE

Before you put the collar on the dog, remove the charging clip. If you do not remove the clip, it may become detached from the collar and become lost.In order to properly detect and correct barks, the collar and device must fit the dog properly. If the collar is too loose or positioned incorrectly, bark corrections may be inconsistent. This can delay or prevent the dog from learning not to bark.

• Place the collar around the middle of the dog’s
• Position the device at the front of the dog’s neck, with the status LED facing towards the dog’s chin and the contact points against the

TIP: The device contact points should be positioned near the dog’s vocal cords. This location varies based on the breed of dog. If the device does not seem to detect the dog’s barks, you should move the device closer to or further from the dog’s body to find the ideal location.

• Tighten the strap so that it is very snug around the dog’s neck, and fasten the

NOTE: The collar should fit tightly and should not be able to rotate or slide on the dog’s neck. The dog must be able to swallow food and water normally. You should observe your dog’s behavior to verify that the collar is not too tight.

Replacing the BarkLimiter Deluxe Battery Assembly

Before you replace the battery, you must remove all dirt, water, and debris from the device. You also need the security screwdriver included with the new battery assembly.You can purchase a replacement battery assembly at http://buy.garmin.com or from your Garmin dealer. The battery assembly includes a pre-assembled back plate with a gasket, battery, and battery connector.

• Remove the four security screws from the corners of the
• Lift up the battery
• Disconnect the battery connector from the

TIP: You should grip the wires close to the connector and pull the connector outward from the circuit board.

• With the new battery assembly, connect the battery connector to the

When properly installed, the connector plug snaps into the port and the top face of the connector plug is flush with the edges of the port.

• Verify that the gasket is not damaged and that it is completely seated in the
• Hold the battery assembly and the device firmly together,and replace all four security screws without

Verify that the battery assembly and the device are aligned with no gaps

Getting More Information

You can find more information about this product on the Garmin® website.

• Go togarmin.com/outdoor.
• Go togarmin.com/learningcenter.
• Go to http://buy.garmin.com, or contact your Garmin dealer for information about optional accessories and replacement parts.

Registering Your Device

Help us better support you by completing our online registration today.

• Go tohttp://my.garmin.com.
• Tighten the screws

DOWNLOAD LINK

Garmin Bark limiter Series Owner Manual

https://static.garmin.com/pumac/barklimiter