Polk MM1 SERIES 6.5 Coaxial Speakers Manual
WIRING DIAGRAMS
- Figure 1
Basic coaxial connection
- Figure 2
Basic component connection installing MM6502
MOUNTING DIAGRAMS - Figure 3
Crossover mounting allows for proper ventilation. Tweeter Attenuation Switch located outside crossover box, move to desired
tweeter level setting.
- Figure 4
Installing MM522, MM652, MM692, & MM6502 models with grille
- Figure 5
Installing MM572 oval models - Figure 6
Flush mount tweeter mounting- Check for proper clearance: The flush mount kit is 1” (26mm) deep.
- Mark the center of the spot and cut a 2” (50.8mm) diameter hole using a hole saw, drill bit or razor knife.
- Assemble the cup, clamp and machine screw loosely as shown.
- Route wires through the round opening in the bottom of the cup.
- Press the assembly into the 2” (50.8mm) diameter hole until the clamp edge is below the mounting surface, then tighten the screw. The legs of the clamp can be bent outward by inserting a screwdriver through the holes in the cup
while still mounted. - Connect wires from the tweeter terminals of the Crossover to the tweeter itself using the faston connectors. Connect the red wire from the (+) terminal of the Crossover tweeter output to the red (+) wire from the tweeter.
- Mount the tweeter by snapping it into the mounting cup.
- Figure 7
Surface mount tweeter mounting- Using the base of the surface mount cup as a template, mark the screw hole and drill them using a 1/8” (3mm) drill bit. Drill a second hole (for the speaker wire) using a 3/16” (5mm) drill bit.
- Screw surface mount cup to the panel.
- Push the tweeter wires through the open area at the bottom of the cup and through the 3/16” (5mm) hole in the panel.
- Connect wires from the tweeter terminals of the Crossover to the tweeter wires using fast on connectors. Be sure to connect the red wire strand from the tweeter to the (+) terminal of the crossover tweeter output.
- Mount the tweeter by snapping it into the mounting cup.
MM1 Series Coaxial and Component Systems Specifications
| MM522 | MM572 | MM652 | MM692 | MM6502 | |
| Type
| 5.25˝ Coaxial | 5˝x 7˝ Coaxial | 6.5˝ Coaxial | 6˝x 9˝ Three Way | 6.5˝ Component System |
| Driver Complement (inches & mm)
| 5.25˝ 133.35 mm | 5˝x 7˝ 127 mm x 177.8 mm | 6.5˝ 165.2 mm | 6˝x 9˝ 152.4 mm x 228.6 mm | 6.5˝ 165.2 mm |
| Tweeter Complement (inches & mm) | 1˝ 25 mm | 1˝ 25 mm | 1˝ 25 mm | 1˝+ 3/4˝ 25 mm + 19 mm | 1˝ 25 mm |
| Cutout Dimensions (inches & mm) | 4.61˝ 117 mm | 4.92˝x 7.15˝ 125 mm x 181.6 mm | 5˝ 127 mm | 5.63˝x 8.42˝ 143 mm x 213.8 mm | 5˝ 127 mm |
| Mounting Height (inches & mm) | 0.20˝ 5.07 mm | 0.25˝ 6.35 mm | 0.32˝ 8.07 mm | 0.30˝ 7.60 mm | 0.32˝ 8.07 mm |
| Mounting Depth: Top (inches & mm) | 2.37˝ 60.1 mm | 2.56˝ 65 mm | 2.62˝ 66.5 mm | 3.07˝ 78 mm | 2.62˝ 66.5 mm |
| Mounting Depth: Bottom (inches & mm) | 2.57˝ 65.2 mm | 2.82˝ 71.5 mm | 2.86˝ 72.6 mm | 3.38˝ 85.8 mm | 2.86˝ 72.6 mm |
| Peak Power Handling | 240 W | 300 W | 300 W | 450 W | 375 W |
| Continuous Power Handling Puissance continue | 80 W | 100 W | 100 W | 150 W | 125 W |
| Nominal Impedance (ohm) | 4 | 4 | 4 | 4 | 4 |
| Frequency Response (Hz) | 50Hz-40kHz | 35Hz-40kHz | 40Hz-40kHz | 30Hz-40kHz | 35Hz-40kHz |
| Grille Height | 0.92˝ 23.3 mm | N/A | 0.95˝ 24.2 mm | 1.03˝ 26.2 mm | 0.95˝ 24.2 mm |
| Sensitivity (dB) | 92 | 93 | 93 | 94 | 93 |
Getting Started
Please inspect your loudspeakers carefully. Notify your Polk dealer if you notice any damage or missing items. Keep the carton and packing material; this will do the best job of protecting your loudspeakers if they must be transported.
Safe Limits of Operation
Damage to loudspeakers can occur when an amplifier, regardless of its wattage, is made to play at higher listening levels than it can produce at low distortion levels. This is usually beyond the “noon or 1 o’clock” position on the volume control. Operation at this level can result in very high levels of audible distortion originating in the amplifier, which can add a harsh, gritty sound to your listening material. Contrary to popular belief, a loudspeaker is more likely to be damaged by trying to get too much volume from a low-powered amplifier or receiver than from a high-powered one.
Technical Assistance or Service
If, after following the hookup directions, you experience difficulty, please double-check all wire connections. Should you isolate the problem to the loudspeaker, contact the authorized Polk dealer where you made your purchase, or contact Polk Customer Service 800-377-7655 (M-F, 9-5:30 EST, US only) or via email polkcs@polkaudio.com. Outside the US, call
410-358-3600. More detailed information—including audio how-to articles, FAQs, and online manuals—is available on our website www.polkaudio.com.
Product Disposal
Certain international, national and/or local laws and/or regulations may apply regarding the disposal of this product. For further detailed information, please contact the retailer where you purchased this product or the Polk Importer/Distributor in your country. A listing of Polk Importer/Distributors can be found on the Polk website www.polkaudio.com or by contacting Polk at
1 Viper Way, Vista, California 92081 USA— Phone: +1 800-377-7655
Limited Warranty
Polk Audio, Inc. warrants the original purchaser only that this product will be free from defects in materials and workmanship for a period of (1) one year from the date of original retail purchase from a Polk Authorized Dealer. However, this warranty will automatically terminate prior to the expiration of the (1) one year period if the original retail purchaser sells or otherwise transfers the product to any other party.
The original retail purchaser shall herein after be referred to as “you.” To allow Polk to offer the best possible warranty service, please fill out the Product Registration Card(s) and send them to the factory at the address provided in the Registration Card within (10) ten days of the date of purchase.
DOWNLOLAD LINK
https://www.polkaudio.com/-/media/files/documentmaster/polk-us/mm1_speaker_online-manual.pdf
