CONAIR-HC25-Close-Cut-Clipper-featured

CONAIR HC25 Close Cut Clipper User Manual

Conair-logo

CONAIR HC25 Close Cut Clipper

CONAIR-HC25-Close-Cut-Clipper-product 

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety pre-cautions should always be taken, including the following:

READ ALL INSTRUCTIONS BEFORE USINGFOR HOUSEHOLD USE ONLYKEEP AWAY FROM WATER

DANGER

Any appliance is electrically live, even when the switch is off. To reduce the risk of death or injury by electric shock:

  • Always unplug this appliance from electrical outlet immediately after using.
  • Unplug this appliance before cleaning. Unplug the appliance when not in use.
  • Do not place or store appliance where it can fall or be pulled into a tub or sink.
  • Do not use while bathing or in a shower.
  • Do not place in, or drop into water or other liquids.
  • Do not reach for an appliance that has fallen into water. Unplug immediately.
WARNING

To reduce the risk of burns, electric shock, fire, or injury to persons:

  • This appliance should never be left unattended when plugged in. Do not pull, twist, or wrap line cord around appliance.
  • This appliance should not be used by, on, or near children or individuals with certain disabilities.
  • Use this appliance only for its intended purpose as described in this manual. Do not use attachments not recommended by the manufacturer. Do not use an extension cord to operate this appliance.
  • Never operate this appliance if it has a damaged cord or plug, if it is not working properly or if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.
  • Keep the cord away from heated surfaces.
  • Never drop or insert any object into any opening on this appliance.
  • Do not place appliance on any surface while it is operating.
  • Do not use this appliance with a damaged or broken comb or with teeth missing from the blades as injury may occur. Before use, make certain blades are aligned properly. (See “Care of Your Clipper/Trimmer.”)
  • Do not use outdoors or operate where aerosol (spray) products are being used or where oxy-gen is being administered.
  • Never operate the appliance with the air openings blocked or while on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and other debris.
  • Avoid skin contact with moving blades.
  • When using the appliance with its cord, be mindful of tangles or kinks in the cord. If the cord does become tangled during use, turn the unit off, unplug from outlet and appliance, and straighten cord before operating again.

THIS PRODUCT IS FOR HOUSEHOLD USE ONLYSAVE THESE INSTRUCTIONS

OPERATION

For dry location use only. Do not expose to water.2. When not in use, unplug unit completely.3. Unit will become warm during operation.

TROUBLESHOOTING

If your corded trimmer does not seem to be functioning, take the following troubleshooting steps before returning it for repair:

  • Be sure the electrical outlet is working by plugging in another appliance to test the outlet.
  • Make sure the electrical plug is not connected to a switch that turns power off when lights are turned off.

OPERATING INSTRUCTIONS

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. Do not attempt to defeat this safety feature.

USER MAINTENANCE INSTRUCTIONSOILING THE BLADES (OIL NOT INCLUDED)

About once a month you should oil the blades. It is best to do this over a piece of newspaper. Turn the unit on and hold it so that the blades are pointed downward. Spread one drop of lubricating oil across the blades, then turn the unit off and wipe away the excess oil with a soft cloth. Be careful not to use too much oil and don’t oil more than necessary, as this could damage the motor. (Never attempt to oil the motor bearing, as it is permanently lubricated.) After oiling the blades, return the unit to storage. Keep oil away from children.

BLADE CARE

Because the titanium coated blades stay sharper longer and are precision made for a very special use, they should always be handled with care. Each time you finish use, take a cleaning brush and brush away any loose hair that has collected in the blades. Then store the unit in the storage pouch provided to protect the blades until the next use. To promote the long life of the appliance, use your trimmer only for the purpose intended by the manufacturer.

THE CONAIR GUIDETO CUTTING HAIR AT HOME

Before you start:

  • Inspect your clipper. Make sure it’s free of hair and dirt, is properly oiled, and running smoothly.
  • Place a towel around the neck of the person.
  • Seat the person so that his or her head is at your eye level. This gives you greater visibility and control.
  • First, comb hair until it’s tangle free. Then hold clipper in a comfortable grip. Now you’re ready to cut.
MEDIUM TO LONG CUT

o begin with, cut only a small amount of hair until you become used to the length each attachment leaves the hair. Try the longest attachment on the clipper first. If you want a shorter cut, you can then use shorter combs.

  • Short attachment comb (number AC404) cuts hair to 1/16″ (1.5mm)
  • Short-Medium attachment comb (number AC405) cuts hair to 1/8″ (3mm)
  • Medium-Long attachment comb (number AC406) cuts hair to 1/4″ (6mm)
  • Long attachment comb (number AC407) cuts hair to 3/8″ (9mm)

Attach combs by holding them teeth up, then snapping onto the bottom of the clipper blade.To remove comb attachments, place index finger and thumb on bottom of comb, then pull out and up.

NOTE: Never push or shove the clipper through the hair to make it move more quickly. Professional experience shows that the clipper works most efficiently when it cuts through the hair at its own speed.

TRIMMING

The Close Cut 10′ corded clipper can also be used as a trimming and detailing tool. Great for touch-ups, trims and fine line detailing between haircuts.

OUTLINING

Outlining requires no attachments. Comb hair into the desired style. Position the clip-per between the sideburns and the ear (see below), making sure the corner edge of the blade is against the hairline. With the outline of the hair as your guide, slowly move the clipper over, around and behind the ears. For the back of the neck and the sideburns, hold the clipper upside down and, holding it against the skin at the length desired, move the clipper downward.

CONAIR-HC25-Close-Cut-Clipper-Fig1

STOP. COMB. CHECK.

For best results, do as the professionals do: Comb hair often, and check clipping results as you comb. This way you avoid uneven sides, bangs, neckline, etc.

USE FOR TRIMMING YOUR BEARD OR MUSTACHE
  • The clipper includes four comb attachments, which provide lengths of 1/16″(shortest) to 3/8″ (longest).
  • To use one of the attachments, press it down over the blades until it clicks into position. At first, until you become familiar with the combs, use the longest comb first. (You can always go back and make your beard or mustache a little shorter.)
  • It is always best to begin with a clean, slightly damp beard/mustache.
  • After you have combed through your beard/mustache in the direction it grows naturally, begin trimming using smooth, even strokes. Start with your sideburns and work down-ward toward your chin. (Never attempt to trim against the natural growth of your beard/mustache because the hair will be cut too short.)
  • If you decide you want a closer trim, you can now switch to the shorter comb (1/16″) and go over your beard/mustache again until you achieve the desired length.
  • After your beard/mustache has been trimmed to the desired length, remove the attachment comb and, using the blades only, define the outlines of your beard/mustache.
  • Turn off the clipper and remove the attachment by gently pulling up on the tab.
CARE OF YOUR CLIPPER/TRIMMERREPLACEMENT (REMOVAL) OF BLADE SET

To remove blade set, make sure the unit is in the OFF position. Remove the blade set by placing thumb against the smaller cutter and pushing forward, releasing the cutter assembly from the housing. Replace with new cutting system and reverse the removal procedure, only this time place your thumb on the large cutter and snap into place.

CONAIR-HC25-Close-Cut-Clipper-Fig2

If clipper stops cutting, check to see if there is a clump of hair lodged between the blades. If that is the problem, unplug the clipper and then detach the blade to remove the hair. If the clipper stops cutting, but does not stop running, you will need to check the blades. For new blades, send check or money order for $6.50, which includes postage and handling (if $10 minimum is met) to:

Conair Corporation 150 Milford Rd. East Windsor, NJ 08520

NOTE: Never pull on the clipper cord. Never twist or wrap the cord around the clipper. Lay it flat with the cord coiled up when not in use.

STORAGE

When not in use, your clipper should be dis-connected, allowed to cool and stored in a safe, dry location, out of reach of children. Any other servicing should be performed by an authorized service representative. This appliance has no user-serviceable parts. The product is for household use.

WARNING:IF YOU THINKTHE POWER IS OFFWHEN THE SWITCHIS OFF,YOU’RE WRONG. KEEP AWAY FROM WATER

CONAIR-HC25-Close-Cut-Clipper-Fig3

Everyone knows that electricity and water are a dangerous combination. But did you know that an electric appliance is still electrically live even if the switch is off? If the plug is in, the power is on. So when you are not using your appliances, keep them unplugged.

LIMITED TWO-YEAR WARRANTY(U.S. AND CANADA ONLY)

Conair will repair or replace (at our option) your unit free of charge for 24 months from the date of purchase if the appliance is defective in workmanship or materials. To obtain service under this warranty, return the defective product to the service center listed on back, together with your purchase receipt and $3.00 for postage and handling. California residents need only provide proof of purchase and should call 1-800-3-CONAIR for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 24 months from the date of manufacture.

Please register this product at www.conair.com/registration Service Center Conair Corporation Service Department7475 North Glen Harbor Blvd. Glendale, AZ 85307©2016 Conair Corporation150 Milford Road, East Windsor, NJ 085207475 North Glen Harbor Blvd., Glendale, AZ 85307

DOWNLOAD PDF LINK

https://www.conair.com/en/close-cut-hair-clipper/HC25.html?lang=en_US

Leave a Reply