Shark GI468 10 Rapido Electronic Iron Owner’s Guide

Shark GI468 10 Rapido Electronic Iron Owner’s Guide

IMPORTANT SAFETY INSTRUCTIONS

When using your iron, basic safety precautions should always be followed, including the following:

• Read all instructions carefully.
• Use iron only for its intended use.
• To protect against risk of electrical shock, do not immerse the iron in water or other liquids.
• Never yank cord to disconnect from outlet. Grasp plug and pull to disconnect.
• Do not allow cord to touch hot surfaces. Let iron cool completely before putting away.
• Always disconnect iron from electrical outlet when filling with water, emptying, or when not in use.
• Do not operate iron with a damaged  cord, or after the iron has been dropped or damaged in any manner. To avoid the risk of electric shock, do not disassemble the iron. Return the iron to EURO-PRO Operating LLC for examination and repair. Incorrect reassembly can cause the risk of electric shock when the iron is used.
• Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while connected or on an ironing board.
• Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down; there may be hot water in the reservoir.
• Never use or rest iron on an unstable surface.
• While the iron is hot, never set iron on an unprotected surface – even if it is on its heel rest.
• CAUTION: TO PREVENT ELECTRIC SHOCK OR OTHER INJURY, before filling the iron with water, make sure that the plug is removed from the outlet
• WARNING: Never fill the iron with fabric conditioner, starches or any other solution, as these will damage the steam mechanism. Do not use contaminated water.
• CAUTION: TO AVOID FIRE, never leave iron unattended while it is plugged in.
• CAUTION: TO PREVENT ELECTRIC SHOCK, never use the iron in a location where it can fall or be pulled into water or another liquid. If the iron falls into water or other liquid, unplug it immediately. DO NOT reach into the water or liquid.
• WARNING: Never use scouring pads, abrasive or chemical cleaners, or solvents to clean the exterior or soleplate of your iron. Doing so will scratch and/or damage the surface.
• CAUTION: DO NOT aim iron at face, towards yourself, or anyone else while using or adjusting steam. Burns or serious injury may occur.
• Always store your iron standing upright, not on the soleplate. If stored face down, even the smallest amount of moisture will cause the soleplate to corrode and stain.
• This appliance is for household use only.

SPECIAL INSTRUCTIONS

• To avoid a circuit overload, do not operate another high-wattage appliance on the same circuit.
• If an extension cord is absolutely necessary, use a 15-ampere cord. Cords rated for less amperage may overheat. Use care to arrange the cord so that it cannot be pulled or tripped over.

POLARIZED PLUG: This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature

SAVE THESE INSTRUCTIONS  For Household Use Only

GETTING TO KNOW YOUR ELECTRONIC IRON

Before using your Rapido Electronic Iron, remove any labels, stickers or tags that may be attached to the body or soleplate of the iron. When turned on for the first time, your new iron may emit an odor for up to 10 minutes. This is due to the initial heating of the materials used in making the iron. The odor is safe and should not reoccur after initial heating. Also, before ironing with steam for the first time, allow iron to heat, hold in a horizontal position and hit the burst of steam button several times. The iron may emit some small particles from the steam holes. This is normal and will clear after pressing the burst of steam button several times.

• Electronic Temperature Control
• Display Panel
• Atomizer Spray Button
• Burst of Steam Button
• Variable Steam Control
• Water Inlet Door
• Spray Nozzle
• Water Level Window
• Stainless Steel Soleplate
• Handle
• Auto-Shut-Off
• Power On Light
• Fabric Settings
• Temperature & Steam Indicators
• Water Flask

FEATURES OF RAPIDO ELECTRONIC IRON

• BURST OF STEAM BUTTON
  Burst of steam provides extra, sudden bursts of steam which aid in removing stubborn wrinkles from fabrics such as denim, cotton or linen.
• ATOMIZER SPRAY BUTTON
  Pressing this button provides a defined jet of spray which gently moistens fabric.
• VARIABLE STEAM CONTROL
  Minimum to maximum steaming for different materials. Self cleaning feature flushes internal sole plate with water.
• ANTI-DRIP FUNCTION
  Cuts off water when the iron temperature is too low.
• BUILT-IN ANTI-CALCIUM FILTER
  Prevents calcium build-up and prolongs the life of the iron.
• STAINLESS STEEL SOLEPLATE
  Provides maximum glide-ability and heat retention.

LED Display Panel

• LED DISPLAY PANEL
  Displays the fabric setting (left) and the temperature indicators (right).

• WATER FILLING INLET
  The cover prevents dust and foreign matter from entering the water tank. It also stops any water from spilling during ironing.
• PIVOT CORD
  For left or right handed use. Pivots up and down; prevents dragging along the fabric. The flexible cord protector protects the cord from raying.

OPERATING INSTRUCTIONS

This appliance is for HOUSEHOLD USE ONLY and may be plugged into any 120V AC polarized electrical outlet. Do not use any other type of outlet.

FABRIC & TEMPERATURE INDICATORS

Press on the Electronic Temperature Control to select the desired fabric setting. The red lights at the left of the LED Display Panel will light up. At the same time, the temperature indicator lights on the right side of the LED Display Panel will start to flash. They will stop flashing when the iron reaches the selected temperature.

DRY IRONING

For dry ironing, turn the variable steam control dial to the left to “0”. This will cut off the steam flow if water is in the water tank. All marked fabric settings on the LED Display Panel can be used for dry ironing.

• Plug the cord into a polarized, 120V AC electrical outlet. The power “ON” light will come on, indicating that the iron is receiving power.
• Press on the electronic temperature control button to select the desired fabric/temperature setting. Turn the variable steam control to “0”. (See “Ironing Guide” for a guide to temperature selection.)
• Place iron on its heel (on a stable, protected surface) while iron is warming to desired temperature.

STEAM IRONING

CAUTION: DO NOT aim iron at face, towards yourself, or anyone else while using or adjusting steam. Burns or serious injury may occur.

WARNING: Before filling the iron with water, be sure the iron is not plugged into the electrical outlet. The iron may be filled with water while it is hot.

CAUTION: TO PREVENT THE RISK OF BURNS, use caution when filling iron with water. Burns can occur from touching hot metal parts, hot water, or steam.

NOTE: Because of the soleplate design, ordinary tap water may be used with this iron. However, in very hard water areas, we recommend using distilled or demineralized water.

WARNING: Never fill the iron with fabric conditioner, starches or any other liquid, as these will damage the steam mechanism. Do not use contaminated water.

• Open the water filling inlet cover. Holding the iron at a slight angle, pour water slowly into the water filling inlet. (Fig. 1) Fill tank to desired level or to the “MAX” water level marking using the water filling flask. (When the iron is upright, the see-through water tank allows you to gauge the amount of water.) DO NOT overfill the tank. When finished filling the iron with water, close the water inlet cover before continuing.

• Plug the cord into a polarized, 120V AC electrical outlet.
• Press on the electronic temperature control button to select the desired fabric and temperature setting. Turn the variable steam control dial to the desired steam setting. (See “Ironing Guide” for a guide to temperature selection.)
• Place the iron on its heel on a stable, protected surface and allow the iron to heat for approximately two (2) minutes or until the temperature settings on the right side of the LED display panel have stopped flashing.
• Turn the variable steam control dial to the right to increase the amount of steam. When using extra steam, the iron uses more water and it may be necessary to fill the water tank more often. (Fig. 2)

BURST OF STEAM BUTTON

CAUTION: DO NOT aim iron at face, towards yourself, or anyone else while using or adjusting steam. Burns or serious injury may occur. The burst of steam position is useful when ironing denim, cotton and linens. It provides quick bursts of steam which aid in removing stubborn wrinkles. The burst of steam feature can be used with Dry or Steam ironing as desired.

• Make sure the water tank is at least 1/2 filled with water.
• Select the desired fabric and temperature setting. Place the iron on its heel (on a stable, protected surface) and allow it to heat for approximately 2 minutes.
• Position variable steam control to the burst of steam position. (Fig. 3)
• With the iron in a horizontal position, press the steam button several times to prime the pump.

• Slide the variable steam control to the right to increase the amount of steam. (Fig. 3) When using extra steam, the iron uses more water and it may be necessary to fill the tank more often. See page 4 for refilling the iron with water.
• Steam is produced as soon as the iron is held in the horizontal position. Steam will stop coming out when the iron is put on its heel in a vertical position or by setting the variable steam control to “0”.

ATOMIZER SPRAY NOZZLE

The atomizer spray nozzle is useful on fabrics with stubborn wrinkles. Press the spray button and a jet of water will spray onto the fabric being ironed. (Fig. 4) The water spray can be used with dry or steam ironing as desired.

SELECTING IRON TEMPERATURES

Always read garment labels and follow the manufacturer’s ironing instructions. Refer to the “Ironing Chart” on page 9 for temperature recommendations:

• Use low settings for nylon and other synthetics.
• Use moderate settings for wool, silks, and blends.
• Use high settings for cottons and linens.
• Stand the iron upright on its heel.
• Plug the cord into a polarized, 120V AC electrical outlet.
• Press the electronic temperature control until you get the desired fabric/temperature setting.
• The light on the right side of the LED display panel will stop flashing when the desired temperature has been reached. (Fig. 5)

IRONING HINTS

WARNING: To prevent fire, do not leave iron unattended while connected.

• Sort articles to be ironed according to the type of fabric. This will reduce the need to adjust the temperature for different types of garments.
• If you are not sure of the fiber content of a garment, test fabric by ironing a small area such as a seam or inside hem section before ironing a visible area. Start with a low temperature setting and gradually increase to find the best setting.
• When reducing the temperature to iron sensitive fabrics, allow approximately 2 minutes for the iron to cool to the new temperature setting.
• Fabrics such as velour, wool, linen and silk are best ironed with an ironing cloth to prevent shine marks.

AUTO SHUT-OFF

The Rapido Electronic Iron is equipped with an electronic auto-off. The electronic auto-off switches the iron off if it has been left standing unmoved in any position (sideways, flat or upright) for approximately 7-9 minutes. A red light on the LED display panel will flash when the iron switches itself off. (Fig. 6) To switch the iron back on, hold the iron horizontally in front of you, gently rock the iron back and forth several times until the “Power ON” light is reilluminated. Then re-set the temperature to the desired setting. DO NOT SHAKE THE IRON.

Note: The iron may require additional warm-up time if the auto-off feature was activated for an extended period.

EMPTYING THE IRON

• Always empty iron after each use.
• When finished using the iron, turn the variable steam control to “0” and press the electronic temperature control button until the power light is lit.
• Unplug the iron from the electrical outlet.
• Turn the iron upside down over the sink with the tip pointing downward and allow the water to flow from the opening.
• Place iron upright and allow to cool before storing.

CAUTION: Use caution when emptying the iron. Burns may occur from touching hot metal surfaces, hot  water or steam.

SELF CLEANING

It is important to “Self Clean” the iron at least every two weeks to remove scale, calcium, etc. The harder the water, the more often the iron should be self cleaned.

• Set the variable steam control to any steam position.
• Fill the water tank up to the “MAX” level.
• Stand the iron on its heel. Plug the iron into the electrical outlet.
• Press the electronic temperature control button until you get the “MAX” temperature setting on the display panel and wait until the iron heats up and temperature setting light stops flashing.
• Turn the variable steam control all the way to the right to the selfcleaning position and hold the iron horizontally over the sink. (Fig. 7)
• Boiling water and steam will now be ejected from the holes in the soleplate. Use caution when doing this as the water and the steam are hot enough to cause burns. The impurities and scale are washed away with it.
• Move the iron back and forth as this happens.
• If there is any water left in the water tank after the iron stops steaming, just empty the remaining water in a sink following the instructions for emptying the iron.
• Turn the variable steam control to the “0” position when the water tank is empty.
• Place the iron back upright on its heel to cool down before storing.

STORAGE

• Always turn the variable steam control to “0” after you have emptied the water tank.
• Allow the iron to cool down.
• Always store the iron in the upright position to protect the soleplate.
• From time to time, clean the exterior of the iron with a damp cloth and wipe dry.
• If you use spray starch, wipe the soleplate occasionally with a soft damp cloth to prevent the build-up of deposits.
• If the iron has not been used for a few weeks, hold the iron horizontally and allow to steam for 2 minutes before ironing.

NOTE: The anti drip function reduces water dripping and water stains. It does not prevent water dripping and water stains if you press the steam burst button too often or if the temperature is too low. The amount of water droplets will eventually decrease after the iron is used for 2 to 3 tank fuls of steaming and ironing.

IRONING CHART

NOTE: Always refer to the garment care tag for ironing instructions. Before starting to iron delicate fabrics, it is best to first test the temperature of the iron on a hem or an inside seam.

TROUBLESHOOTING

DOWNLOAD PDF LINK

GI468_10-GI468C_10-GI48_12-GI48C_12 Manual_REV_1108B_English_French_ Spanish_PRINTABLE

https://www.sharkclean.com/manual/GI468_REV_0807C_NO_PROP_65_1500_Watt_-_Reader.pdf