Eufy Video Baby Monitor 720p Camera User Manual

Eufy Video Baby Monitor 720p Camera

WHAT’S IN THE BOX

FEATURE INTRODUCTION

Monitor Features

•  Screen
•  Menu button
•  Navigation button • White: Fully charged
•  OK button 7 Micro USB charging port

1.  Press to confirm the selection
2.  Press to switch camera display if you have added more than 1 camera

•  Return to previous level of menu / Talk button

1. Press and hold to speak to the camera
2. When menu is opened, press to return to the previous level of menu

• LED indicator

1. Red: charging
2. White: Fully charged

• Micro USB charging port
• Volume down
• Volume up
• Power button
•  Zoom button
• Reset
• Speaker

Camera Features

• Microphone
• Standard camera lens
• LED indicator
• Temperature sensor
• Pairing button
• Micro USB port
• Speaker

SETTING UP THE CAMERA AND MONITOR
Charge the Monitor

Fully charge the monitor before use. To charge:

1.  Connect one end of the micro USB cable to the baby monitor, and the other end to the power adapter (5V/2A).
2.  Plug the adapter into a power outlet.
3.  Press and hold the power button for 2 seconds to turn the baby monitor on.

Charge the Camera

1.  Connect one end of the micro USB cable to the baby camera, and the other end to the power adapter (5V 1A).
2.  Plug the power adapter into a power outlet.The new baby monitor and camera will set up automatically. You are all set to use the products after the monitor and camera are fully charged.

ADDING A NEW BABY CAMERA TO THE BABY MONITOR

The baby camera and baby monitor are paired and ready to use right out of the box. Refer to the following steps when adding extra baby cameras or after resetting a baby camera.

1.  Enter menu settings, go to Camera -> Add Camera, then follow the onscreen instructions to start the pairing.
2.  Press and hold the pairing button on the rear of the camera for 1 second until a notification prompt is heard.

3. Check the firmware version of the monitor (see image below) to make sure your baby monitor and camera are running the same, latest firmware version.

To check whether it is the latest version:

1. Visit the website below: https://www.eufylife.com/support/5505/spaceview-baby-monitor
2.  If the firmware version is lower than the version shown online (highlighted in green), click the firmware version to download. The downloaded file includes firmware for both T8300 and T8321 models, make sure you use the T8321 firmware.
3.  Follow the steps in the “eufy Security Software Upgrade Guide” video or Firmware Upgrade Manual to complete firmware upgrade.

Note:

• The eufy Security Space view baby camera can be added to the monitor. Before adding the camera, make sure Space View baby camera is running the same, latest version with the monitor’s.
•  Chrome OS is not supported for firmware upgrade.
•  Before you upgrade firmware, use the provided micro USB cable (1m) to connect the device needed to your computer.

USING THE BABY MONITOR

When 2 or more cameras are added to the monitor, you can manually switch among cameras by pressing the monitor’s OK button. Once the camera switch is completed, the icon of the selected camera will appear on the corner of the baby monitor.
You can also select the “Cycle Camera” option. The screen cycles through the list of connected baby cameras according to the preset intervals.

Note: The monitor will emit a loud noise if placed too close to the camera. This is normal and is
resolved once the camera is moved away from the monitor.

MOUNTING THE BABY CAMERA ON THE WALL

1.  Place the wall mount against the wall, matching the direction as UP indicates. Mark the screw holes with a pencil.
2.  Drill 5 1 ” holes into the wall and then insert anchors into the holes. Anchors are not needed for wooden walls
3.  Insert the screws through the mounting holes of the wall mount and screw into the anchors.
4.  Snap the baby camera onto the wall mount
5.  To get the optimal viewing angle, rotate the camera (25°upwards, 60° backwards, 250° horizontally) manually, as pan and tilt functions are not supported on this model when using the navigation button.

MONITOR MENU SETTINGS

Press and hold the power button to power on the monitor. Press the menu button to open Menu Settings.
Menu Settings

Note:

The interval duration between each sound alert is 30 seconds. It will not sound alerts during this interval, even if the conditions are met to trigger an alert.

On-screen Menu Icons

NOTICE:
Warning
Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 1m (3ft) away). Never use extension cords with AC Adapters. Only use the AC Adapters provided.
This product complies with the radio interference requirements of the European Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the Web site: www.eufylife.com This product can be used across EU member states.
Due to the used enclosure material, the product shall only be connected to a USB Interface of version 2.0 or higher. The connection to so called power USB is prohibited. The adapter shall be installed near the equipment and shall be easily accessible.

Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment.
The suitable temperature for T8321-M and accessories is -20°C-40°C
The suitable temperature for T8321-C and accessories is -20°C-40°C
When charging, please place the device in an environment that has a normal room temperature and good ventilation.
It is recommended to charge the device in an environment with a temperature that ranges from 5°C~25°C.
Please ensure to use only the charger offered by the manufacturer. Using unauthorized charger may cause danger and violate the authorization of the device and the guarantee article.
The charger output voltage / current is 5Vdc / 1A(for T8321-C) and 5Vdc / 2A (for T8321-M).The plug considered as disconnect device of adapter.
If you use a third-party charger, the recommended output voltage / current of the adapter is 5Vdc / 1A (for T8321-C) and 5Vdc / 2A (for T8321-M),and the adapter shall be CE approval type.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body.
Operating Frequency Range: 2410-2477MHz
The T8321-C Max Output Power: 19.12dBm(EIRP), The T8321-M Max Output Power: 19.56dBm (EIRP) CE SAR:
This T8321-M was tested for typical body-worn operations with the back of the handset kept 0 mm from the body. The SAR limit of Europe is 4.0 W/kg. Device types T8321-M has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the limb is 0.310W/kg . This device was tested for typical hand held operations with the back of the device kept 0mm from the Limb.
The T8300-C device has been evaluated to meet general RF exposure requirements and can be used in fixed exposure condition. RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body.
Anker Innovations Deutschland GmbH | Georg-Muche-Strasse 3-5, 80807 Munich, Germany Anker Technology (UK) Ltd | Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11 2AA, United Kingdom.

This product is designed and manufactured with high quality materials and components, which can be recycled and reused.

CUSTOMER SERVICE

Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

•  Warranty
  12-month limited warranty
• Call Us
  United States +1 (800) 988 7973 Mon-Fri 9AM-5PM (PT)
  United Kingdom +44 (0) 1604 936 200 Mon-Fri 6AM-11AM (GMT)
  Germany +49 (0) 69 9579 7960 Mon-Fri 6:00-11:00
•  Email Us
  Customer Support: support@eufylife.com