Brinno MAS200D Motion Detector![Brinno- MAS200D- Motion -Detector-prodect](data:image/svg+xml;base64,PHN2ZyB4bWxucz0iaHR0cDovL3d3dy53My5vcmcvMjAwMC9zdmciIHdpZHRoPSIyODAiIGhlaWdodD0iMjY5IiB2aWV3Qm94PSIwIDAgMjgwIDI2OSI+PHJlY3Qgd2lkdGg9IjEwMCUiIGhlaWdodD0iMTAwJSIgc3R5bGU9ImZpbGw6I2NmZDRkYjtmaWxsLW9wYWNpdHk6IDAuMTsiLz48L3N2Zz4=)
Package Contents![Brinno- MAS200D- Motion -Detector-fig-1](data:image/svg+xml;base64,PHN2ZyB4bWxucz0iaHR0cDovL3d3dy53My5vcmcvMjAwMC9zdmciIHdpZHRoPSIzMDAiIGhlaWdodD0iMjc5IiB2aWV3Qm94PSIwIDAgMzAwIDI3OSI+PHJlY3Qgd2lkdGg9IjEwMCUiIGhlaWdodD0iMTAwJSIgc3R5bGU9ImZpbGw6I2NmZDRkYjtmaWxsLW9wYWNpdHk6IDAuMTsiLz48L3N2Zz4=)
- Motion Sensor Unit
- Battery Lock* (inside motion sensor unit)
- 1 CR2450 Battery (inside motion sensor unit)
- Magnetic Wall Mount
- Screwdriver
Device Parts![Brinno- MAS200D- Motion -Detector-fig-2](data:image/svg+xml;base64,PHN2ZyB4bWxucz0iaHR0cDovL3d3dy53My5vcmcvMjAwMC9zdmciIHdpZHRoPSIzMDAiIGhlaWdodD0iMzAwIiB2aWV3Qm94PSIwIDAgMzAwIDMwMCI+PHJlY3Qgd2lkdGg9IjEwMCUiIGhlaWdodD0iMTAwJSIgc3R5bGU9ImZpbGw6I2NmZDRkYjtmaWxsLW9wYWNpdHk6IDAuMTsiLz48L3N2Zz4=)
- Motion Sensor Lens
- Battery Compartment
- Motion Sensor Pairing Channel Switch
- Pairing Button
- LED Indicator
Connect to Camera
Make sure the receiver unit is installed, and the camera is power on. (place the motion sensor close to the camera within 12 in (30cm)).
- Open front cover.
- Remove tab and engage battery to activate motion sensor.
- Pin the pairing button for
- On motion sensor, LED light flashes blue.
- On receiver unit, LED light flashes red.
- On camera screen motion sensor icon appears
Display Icons
- Connected sensors: The icon turns white to indicate the device is successfully connected to the sensor.
- Sensor in low battery: The icon turns red to alert battery dropping low.
Sensor Installation
Hide motion sensor unit anywhere separately near your front door.
Transmission / Detection
Transmission Distance:
32 ft (10m) between motion sensor unit and receiver unit inside the camera. When you choose Portable Mode, make sure the two units are within the trans-
mission distance.
Sensor Detection Area:
Detection angle: 90 degrees (horizontal). Detection distance: 13 ft (4 m) (centerline). (approx. 5 ft (1.5 m) on both sides of the centerline).
Pairing Channels
One camera supports up to 6 motion sensors. You make different channel combinations to identify each unique motion sensor.
Motion Sensor Pairing Channel Switch:
Pairing Channel Combination:
Delete Sensor
- The screen displays all paired sensors. Press SHUTTER button to go to the DELETE SENSOR option.
- Select one sensor or all sensors to be deleted fre the list. Press SHUTTER button confirm deletion.
- Press SHUTTER button again to delete.
- Restart the camera. The selected sensor will be permanently deleted.
Specifications![Brinno- MAS200D- Motion -Detector-fig-20](data:image/svg+xml;base64,PHN2ZyB4bWxucz0iaHR0cDovL3d3dy53My5vcmcvMjAwMC9zdmciIHdpZHRoPSIyNTIiIGhlaWdodD0iMzAwIiB2aWV3Qm94PSIwIDAgMjUyIDMwMCI+PHJlY3Qgd2lkdGg9IjEwMCUiIGhlaWdodD0iMTAwJSIgc3R5bGU9ImZpbGw6I2NmZDRkYjtmaWxsLW9wYWNpdHk6IDAuMTsiLz48L3N2Zz4=)
FCC Statement
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT.
This equipment has been tested and found to comply with the limit s for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful n interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit deferent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or medications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules.- Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
FCC RF Radiation Exposure Statement:
- This Transmitter must not be co-located or operating in conjunctior with any other antenna or transmitter.
- This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
15.19 Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference and
- this device must accept any interference received, including interference that may cause undesired operation of the device.
Download Pdf Link