MONSTER 2MNTW0395 Pure DNA Fit Bluetooth Earbuds User Guide
Caution: The batteries in this product are not replaceable. If the battery is exposed to extremely high temperatures it could result in an explosion or the leaking of flammable liquid or gas.
Warning: Do not dispose of the unit in fire or water. Never attempt to disassemble and reassemble. Check with your local authority for recycling advice. Keep your device and all accessories out of the reach of children and animals. Small parts may cause choking or serious injury if swallowed. Avoid exposing your device to very cold or very hot temperatures (Below 0° or above 45° C). Extreme temperatures can cause deforming of the device and reduce the charging capacity and life of your device. Do not allow your device to get wet, liquids can cause serious damage. Do not handle your device with wet hands.
Product Specs
Model No: Monster DNA GO
Version: 5.2 Bluetooth® Chipset
Support profiles: HSP/HFP/A2DP/AVRCP
Frequency response: 20hz-20kHz
Impedance: 32 Ω
Driver size: 12mm
Sensitivity: 110 ±3dB
Effective range: up to 10 meters
Earbud battery capacity: 2 x 50mAh
Playing time: 7-8 hours
Charging case battery capacity: 400mAh
Earbud charging time: Max. 1.5 hour
Charging case charge time: Approx. 1.5 hour
Earbud Operation
Power off: Place the earbuds back in the charging case, ensure that the case is powered, the earbuds will be automatically powered OFF. Or you can press and hold the (MFB) button on either earphone for 9 seconds.
Volume Down:
Press and hold the left “MFB” decrease volume incrementally.
Volume Up:
Press and hold the right “MFB” increase volume incrementally.
Previous Track:
Double press the Left “MFB”.
Next Track:
Double press the Right “MFB”.
Reject Call:
Double press either “MFB”.
End Call:
Press either “MFB” button.
Bluetooth® Pairing
Go to “Bluetooth” Setting on your Bluetooth® device (Phone, Tablet, etc.). Turn the Bluetooth® ON, on your device.
Open the charging case, and take the earbuds out, they will turn on automatically. If this is your first time using your earbuds, they will automatically enter Bluetooth Pairing mode. On your devices Bluetooth menu, select the ‘Monster DNA Go’ earbuds from the list of available devices. To pair your earbuds to a different Bluetooth® device, disconnect from the DNA GO or turn off Bluetooth® pairing on your original device. Remove the earbuds from the case and they will enter pairing mode automatically.
Troubleshoot Tip
If the earbuds do not connect to your device, place the earbuds back in their charging case, turn your device’s Bluetooth OFF and then back ON again, then repeat the pairing process. Your earbuds are designed to automatically sync to each other when they are turned ON.
- LED indicator flashes red and white.
- The case and hold them near each other. If this does not happen, repeat the Factory Reset steps.
- Follow the Bluetooth Pairing Instructions from the beginning to pair to a new device.
Charging the Case
Connect the USB-C™ charging cable into the socket on the charging case. Plug the cable into a standard USB-C™ 5V / 1A output. (LED indicator will flash red or green depending on the battery level.) To check the charging case’s battery level, single press the Charging Case Button.
- 0-10% – The first LED is blinking red.
- 10-33% – The first LED is breathing; the others are OFF.
- 33-66% – The first LED is ON, the second is breathing, the third is OFF.
- 66-99% – The first and second LEDs is ON, the third LED is breathing.
- 100%- All three LEDs are ON.
Warning: To avoid damage to the charging case, please only use a 5V / 1A charger.
Charging the Earbuds
To charge your earbuds, place them the charging case. The earbud LED indication will light up while they are charging and will turn off once they are fully charged. It’s recommended to fully charge your earbuds and charging case before first use.
DOWNLOAD PDF
MONSTER 2MNTW0395 Pure DNA Fit Bluetooth Earbuds User Guide
