Frigidaire GMTK3068AF Stainless-Steel Gallery Microwave Guide
BEFORE YOU BEGIN
IMPORTANT
Save these instructions for the local inspector’s use.
Note to Installer
Be sure to leave these instructions with the Consumer.
Skill level
- Installation of this appliance requires basic mechanical and electrical skills.
- Proper installation is the responsibility of the installer.
- Product failure due to improper installation is not covered under the Warranty.
Read these instructions completely and carefully.
- Please make sure the cabinet is level or vertical to the front panel of the cabinet before installation. Uneven cabinets may cause the trim kits to be noncoplanar with the door panels of the microwave oven.
- Unplug the microwave oven before attempting installation of this kit.
- Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury.
- Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
- A statement shall be included in the instructions warning the user that the appliance must be disconnected from the source of supply before attempting the installation of the accessory, and that the accessory is intended for use only with an appliance that is marked to indicate such use.
Installation Instructions
PARTS INCLUDED IN THE KIT
- Front Frame Assembly- QTY 1
- Exhaust Duct – QTY 1 Bottom Mounting Rail – QTY 2
CHOOSING A LOCATION FOR YOUR MICROWAVE OVEN IF BUILT-IN
Built-In Trim Kit allows for the installation of microwaves listed below to be built into a cabinet or wall by itself or over an electric wall oven*
| Model Number | Color | Description |
| GMBS3068AF | Easy Care SS | Microwave |
| GMBS3068AD | Black SS | Microwave |
| GMTK3068AF | Easy Care SS | 30″ Trim Kit |
| GMTK2768AF | Easy Care SS | 27″ Trim Kit |
| GMTK3068AD | Black SS | 30″ Trim Kit |
| GMTK2768AD | Black SS | 27″ Trim Kit |
See Illustration 1 for the proper location and when building above a wall oven. Carefully follow both the wall oven installation instructions and Electrolux’s Built-in Kit instructions. If building over a wall oven, be sure the clearance between the wall oven and the microwave oven is a minimum of 3 inches. NOTE: A Trim Kit and a microwave can only be built in over an electric self-clean or non-self-clean single cavity wall oven.
CABINET OR WALL CUTOUT
| Height (A) Minimum | 16 3/4 ” (42.5 cm) |
| Maximum | 17 ” (43.2 cm) |
| Width (B) Minimum | 24 3/4 ” (62.9 cm) |
| Maximum | 25″ (63.5 cm) |
| Depth (C) Minimum | 20″ (50.8 cm) |
| Trim Kit Overall Dimensions | ||
| 27″ | 30″ | |
| Height | 18″（460.8mm） | 18″（460.8mm） |
| Width | 27″（685.8mm） | 30″（759mm） |
| Depth | 1 3/5″ (40.9mm) | 1 3/5″ (40.9mm) |
ELECTRICAL OUTLET LOCATION
NOTE
The floor of the opening should be constructed of plywood strong enough to support the weight of the oven and floor load (approximately 100 pounds). The floor should be level for proper operation of the oven. Be sure to check the local building code as it may require that the opening be enclosed with side, ceiling, and rear partitions. The proper functioning of the oven does not require the enclosure.
EXHAUST DUCT ASSEMBLY
- Draw a Central Line on the floor. Place the Exhaust Duct in the opening， When the Exhaust Duct Assembly is in the opening correctly, the Center Line is in the middle of the Exhaust Duct Assembly.
- Secure the Exhaust Duct Assembly with the three screws A. IMPORTANT: Secure screws in the outer hole. are needed for exhaust duct assembly.
Bottom Mounting Rail
Turn the microwave upside down so you are looking at the oven bottom. Secure the bottom Mounting Rail on the oven with four SCREWS A.
NOTE:
Please make sure to align the holes(marked with “36”) of the bottom mounting rail and the holes(marked with “36”) of the microwave oven’s bottom plate
OVEN INSTALLATION
- Place the oven adjacent to the wall or cabinet opening. Plug the power cord into the electrical outlet.
- Carefully guide the assembled oven into the prepared opening. Slide the oven on the Exhaust Duct Assembly.
- Secure the Exhaust Duct Assembly with the four screws A.
FRAME INSTALLATION
- Position the FRAME ASSEMBLY to be square with the oven. Carefully place the FRAME ASSEMBLY on the oven. See Illustration 7.
- Check that it is level and then secure with two SCREWS B. Secure the bottom portion of the FRAME ASSEMBLY with the two remaining SCREWS B. See Illustration 8.
REFERENCE LINK
DOWNLOAD PDF
Frigidaire GMTK3068AF Stainless-Steel Gallery Microwave Guide
