Veho VHS-010-OC Cave HD outdoor wireless IP camera Manual
Introduction to the Cave HD Outdoor IP Camera
Before pairing the Cave camera with your Cave Smart Hub please read the following. Ensure the camera and Smart Hub is within range of the mobile device that you use to access the Cave app. You will need your router username and password to hand.
IMPORTANT:
Only use the supplied power cable with the camera and a compatible power source. Failure to do so may invalidate your warranty.
Visit our YouTube channel for Cave installation guides
https://www.youtube.com/VehoWorld
Installing the Cave camera
Before installation insert a compatible microSD card, class 10 up to 128GB (not included). Remove the two screws that secure the bottom panel and insert a microSD card into the slot. Secure the bottom panel in place with the two screws.
We recommend the installation is carried out by a qualified Electrician. Before mounting the camera ensure the mounting surface can easily support the weight of the camera.
Pairing the Cave camera
Once installed and plugged into a compatible power source, the Cave camera LED (on the front) will continuously flash green to indicate it is in pairing mode.
Open the Cave app and press the ‘Add Accessory’ button then press ‘By scanning QR Code’.
Scan the QR Code on the base of the camera using the scan window in the app. Take note of the camera pairing name, shown on the screen, next, open the Wi-Fi settings on your device.
Note:
If the camera does not appear on the wi-fi list press and hold the reset button on the rear of the camera for 10 seconds, when released, you will hear a ‘Beep’. The camera should appear within 30 seconds.
Select the camera from the Wi-Fi list and enter the default password ‘01234567’ and click ‘Join’. The camera should connect to your Wi-Fi. Re-enter the Cave app your wi-fi router should be already listed, enter your Wi-Fi router password and confirm the password before clicking ‘Start’. Network configuration may take up to a few minutes. Enter a name for your new IP camera and click the tick icon to save. The camera will now appear in the Cave app under ‘Smart cameras’. To view the camera for the first time, you will need to reset the default password. Press ‘OK’ and enter a new password, once confirmed the camera will be online and ready to view.
Live view, recording & playback
Click on the ‘Smart Camera’ icon on the home screen where all IP cameras are listed. For a live view of any camera click the play icon on the left. In live view mode, you can take a snapshot, listen to audio, and talk through the camera. To review recorded footage click the ‘Video’ link for a list of recorded events. All footage is automatically saved onto a microSD card (not included).
Camera settings
Change camera password / Motion detection & recording / Sync timezone / Record in HD or SD / Horizontal and vertical flip / Update wi-fi settings / Format SD card.
Specifications
Camera
- Image sensor 1/2.7” 1080P CMOS
- Effective pixels 1920(H) x 1080(V)
- WDR Digital WDR
- Noise Reduction 3D DNR
- Day/Night control (IR-Cut) Auto (ICR)/Colour/B&W
- Motion detection Supported
- SD card Supported, up to 128GB
- IR distance 30m (98.5ft)
General
- Power supply DC 12V/1A
- Hard reset Supported
- Working power <5W
- Working temp -10℃~+55 / 10%~90% RH
- Water resistant IP65
- Dimensions 188mm x 65mm x 60 mm
- Weight 385g
Lens
- Focal length 4mm
- Max aperture F2.4
- Focus control Fixed
- The angle of view is 114°
Network
- Network protocol HTTP, FTP, TCP/IP, UDP, SMTP, DHCP, NTP, UPNP, RTSP, Onvif, DDNS
- App iOS (9.0+), Android (5.0+)
- Wi-Fi Wi-Fi (802.11b/g/n), 2.4G only, supports
- WEP / WPA-PSK /WPA2-PSK encryption
- P2P Supported
Video
- Encode H.265 main profile
- Resolution 1080P (1920×1080), VGA (640×352)
- Video bitrates 32Kbps ~ 8Mbps
- Video frame rate 30fps@1080P
- Image snapshot Supported
Support & troubleshooting
How do you reset the Cave HD Outdoor Wireless IP Camera?
Press and hold the reset button on the rear of the camera until you hear the reset success tone, approximately 10 seconds. Release the button and wait until you hear a beep to confirm the camera is in pairing mode, this can take up to 30 seconds; proceed to set up the camera after the beep.
