Table of contents
show
LG MR20 Magic Remote Control For Smart TV User Guide
Precautions To Take
- Use the remote control within the specified range(within 10 m). You may experience communication failures when using the device outside the coverage area or if there are obstacles within the coverage area.
- You may experience communication failures depending on the accessories. Devices such as a micro wave oven and wireless LAN operate in the same frequency band(2.4 GHz)as the Magic Remote.This may cause communication failures.
- The Magic Remote may not work properly if a wireless router (AP) is within 0.2 m of the TV.Your wireless router should be more than 0.2 m away from the TV.
- Do not disassemble or heat the batteries.
- Do not drop the battery. Avoid extreme shocks to the battery.
- Do not immerse the batteries in water.
Accessories
- Magic Remote and Alkaline Batteries (AA)
- Owner’s manual ( Depending on country)
Installing Batteries
- Press the top of the battery cover, slide it back,and lift the cover as shown below.
- Tore place batteries,open the battery cover, replace alkaline batteries (1.5 V, AA) matching and ends to the label inside the compartment,and close the battery cover. Be sure to point the remote control at there remote control sensor on the TV.
- To remove the batteries,perform the installation actions in reverse. Don’t mix old or used batteries with new ones. Close the cover securely.
- Failure to match the correct polarities of the battery may cause the battery to burst or leak, resulting in fire,personal injury,or ambient pollution
Register/Unregister the Magic Remote
- Turn on the TV and press the Wheel (OK) on the Magic remote for registration.
- Press and hold the (Home)button and (Back)button together for more than 5 seconds to disconnect the Magic Remote.
- Press and hold the (Home)button and (Q. Settings)button together for more than 5 seconds to disconnect and re-register the Magic Remote at the same time.
Remote Description
- Power: Turns the TV on or off.
- Number buttons: Enters numbers.
- Dash: Inserts a between numbers such as 2-1 and 2-2.
- More actions: Displays more remote control functions.
- Volume buttons: Adjusts the volume level.
- Mute: Mutes all sounds.
- Mute: Accesses the[Accessibility] menu.
- Channel buttons / Programme buttons: Scrolls through the saved channels or programmes.
- Voice recognition: Network connection is required to use the voice recognition function. Check for recommended content.
- Voice recognition: Speak while pressing and holding the button to use the voice recognition feature.
- Input: Changes the input source.
- Wheel (OK): Press the center of button to select a menu. You can change channels or programs by using the button.
- Up/Down/Left/Right: Press the up,down, left or right button to scroll the menu. If you press buttons while the pointer is in use, the pointer will disappear from the screen and Magic Remote will operate like a general remote control.To display the pointer on the screen again, shake Magic Remote to the left and right.
- Back: Returns to the previous level.
- Q. Settings: Accesses the Quick Settings.
- Q. Settings: Displays the[All Settings] menu.
Connecting Smart Devices using NFC Tagging
Using the NFC Feature
NFC is technology that uses Near Field Communication,allowing you to conveniently send and receive information without separate settings.
By bringing a smart device near the NFC-enabled remote control,you can install the LG Thin Q app and connect the device to the TV.
- Turn on NFC in the smart device’s settings. To use NFC with Android devices, set the NFC option to enable
‘read/write tags’in the smart device’s settings.The NFC settings may vary depending on the device. - Bring the smart device near the (NFC)on the remote control. The required distance for NFC tagging is
about 1 cm. - Follow the instructions to install the LG Thin Q app on your smart device.
- Re tagging the smart device to the remote control allows you to conveniently access various features on
the connected TV through the LG Thin Q app.
Note:
- This feature is available for NFC-enabled smart devices only.
- This feature is only available if the remote control has an NFC logo.
Specifications
| CATEGORIES | DETAILS | |
| Model No. | MR22GN | |
| Range of frequency | 2.400 GHz to 2.4835 GHz | |
| Output Power (Max.) | 7 dBm | |
| Channel | 40 channels | |
| Power source | AA 1.5 V, 2 alkaline batteries are used | |
| Operational temperature range | 0 °C to 40 °C |
| NFC | EU | Except for EU |
| Range of frequency | 13.553 to 13.567 MHz | 13.56 MHz |
| Output Power (Max.) | -13.27 dBuA/m @ 10 m | – |
