KLIPSCH T4 True Wireless Headphones User Manual

KLIPSCH T4 True Wireless Headphones User Manual

PAIRING

1. Turn on the earbuds by holding down the main buttons (over the logo) on both earbuds for 3 seconds. Alternatively, the earbuds can also be turned on by placing them in the charging case and removing them.
2. Once they are turned on you will hear a prompt indicating that the Left and the Right Channels have been connected, followed by “ready to pair”
3. Now it is time to pair them to your phone. Open up the Bluetooth connection menu of your smartphone or tablet. Connect to “Klipsch T4 True Wireless”. If it does not connect right away wait 5 seconds and try again.
4. Once connected the earbuds will recognize your device and will automatically connect to it every time they are powered on in the future.

AUTO POWER ON/OFF:
There are 2 ways to power on the T4 True Wireless:

1. If they are in the charging case simply remove the earbuds without touching the touch buttons to auto power on the earbuds.
2. If they are not in the charging case or the case has run out of power, press the main buttons on both earbuds for 3 seconds to power on.

There are 2 ways to power off the T4 True Wireless:

1. To auto power off place the earbuds back into the charging case. After 5 seconds the earbuds will automatically turn off and begin the charging process. These features may not work if the charging case has been fully depleted of power.
2. To manually power off press and hold the button over the logo of the earbuds for 3-5 seconds.

CHARGING

FACTORY RESET

CHARGING T4 TRUE WIRELESS:

1. To charge the earbuds simply place them into the corresponding areas of the charging case. Make sure they are securely in the correct position.
2. The red indicator lights will turn on to indicate that they are charging. When charging is complete the red lights will turn off.
3. Close the lid of the case to ensure secure fit and charging.

CHARGING THE CASE:

1. To charge the case plug in the included USB Type-C cable to the rear of the case. Then plug the other end into a power source such as a computer or a USB wall charger. (not included)
2. Charging is complete when the LED at the front of the charging case turns from flashing green to solid green.
3. The case is also compatible with wireless charging.
4. Simply plug in the wireless charging pad and place the charging case with the Klipsch brand facing upward onto the included wireless charging pad and charging will automatically begin.

STATUS INDICATORS

CONTROLS:

IN TWS MODE WITH BOTH L& R EARBUDS PAIRED
Media Play/Pause: Press the main button on the RIGHT earbud to play/pause music or videos Volume Up: Press and hold the main button on the RIGHT earbud for 1-2 seconds to raise the volume Volume Down: Press and hold the main button on the LEFT earbud for 1-2 seconds to lower the volume Media Next: Double press the main button on the RIGHT earbud to skip to the Next song/video Media Previous: Double press the main button on the LEFT earbud to skip to the Previous song /video

CALL HANDLING:
Answering Incoming Call: Press the main button on the RIGHT earbud to answer an incoming phone/video call. End Call or Reject an Incoming Call: Double press the main on the RIGHT earbud to reject an incoming phone/video call or end a call that you are on. Mute: Press the main button on the LEFT earbud to mute yourself during a call. Press again to unmute the microphone. Hang up and answer incoming call: If you are on a call and there is another incoming call at the same time, press the main button on the RIGHT earbud to end the current call and answer the new incoming call.

IN MONO MODE USING ONLY A SINGLE EARBUD

Media Play/Pause: Press the main button on the earbud to play/pause music or videos Siri/Google Assistant: Press and hold the main button on the earbud to activate the voice assistant on your device. CALL HANDLING: Answering Incoming Call: Press the main button on the earbud to answer an incoming phone/video call. End Call or Reject an Incoming Call: Double press the main on the earbud to reject an incoming phone/video call or end a call that you are on. Mute: Press the main button on the earbud to mute yourself during a call. Press again to unmute the microphone.

MONO CONTROLS

IMPORTANT SAFETY INFORMATION

1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all these instructions.
5. DO NOT use this apparatus near water or moisture.
6. If you hear ringing or experience pain or discomfort in your ears during or after using any in-ear audio product, that is a sign you are listening too loud. When your ears are exposed to high volumes (more than 85dB) for over an hour, you may be permanently damaging your hearing.
7. TURN DOWN your listening device’s volume to zero before you insert the Klipsch headphones and turn on the device. Once you have the headphones on, gradually increase the volume to a comfortable, moderate volume.
8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. ONLY USE attachments/accessories specified by the manufacturer.
10. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
11. NEVER operate a motor vehicle while listening to or wearing your headphones. Not only dangerous, it is illegal in many places.
12. NEVER operate heavy machinery while listening to or wearing your headphones.
13. We don’t recommend you use the headphones while riding a bicycle, running, or walking in heavy traffic areas.

WARNING:

Except in case of emergency, Klipsch recommends you do not use these headphones or headsets (headphones plus microphone) as aviation communication equipment as they are not engineered for many environmental conditions common in commercial or non-commercial aircraft (including, but not limited to: altitude, temperature, noise conditions, unpressurized aircraft, etc.) resulting in possible interference to critical communications.

The Occupational Safety Health Administration (OSHA) has issued headphone usage recommendations for maximum daily exposure and sound pressure levels (measured in decibels (dB)). A decibel is a unit of measure of sound, and decibels increase exponentially as sound gets louder. For example, conversational speech is typically around 60dB and a rock concert in a stadium is often about 110 dB.

COMPLIANCE INFORMATION

EU COMPLIANCE INFORMATION
Eligible to bear the CE mark; Conforms to European Union Low Voltage Directive 2006/95/EC; European Union EMC Directive 2014/53/EU; European Union RoHS Directive 2011/65/EU; European Union WEEE Directive 2002/96/EC; European Union Registration, Evaluation, Authorization and Restriction of Chemicals (REACH) Directive 1907|2006.

WEEE NOTICE
Note: This mark applies only to countries within the European Union (EU) and Norway. This appliance is labeled following European Directive 2012/19/EU concerning waste electrical and electronic equipment (WEEE). This label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling.

FCC AND CANADA EMC COMPLIANCE INFORMATION

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver.

OSHA GUIDELINES FOR NOISE EXPOSURE LIMITS

FCC RADIATION EXPOSURE STATEMENT

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Approved under the verification provision of FCC Part 15 as a Class B Digital Device. Caution: Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this device. Caution:

To comply with the limits of Class B digital devices, according to Part 15 of the FCC rules, this device is to comply with Class B limits. all peripherals must be shielded and grounded. Operation with non-certified peripherals or non-shielded cables may result in interference to radio or reception. This Class B digital apparatus complies with Canadian ICES-002

WIRELESS TRANSMITTER COMPLIANCE INFORMATION
This device complies with ISEDC license-exempt RSS standard (s)Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

PRODUCT REGISTRATION
Register your product online at www.klipsch.com/register

• Klipsch will keep you up-to-date on new products and promotions.
• Your personal information will never be resold.
• This registration information is not used for warranty purposes. Please retain your receipt for warranty claims.

WARRANTY INFORMATION

Klipsch Group, Inc., (KGI) warrants to the original retail purchaser that this product is to be free from defective materials and workmanship for two (2) years from the date of purchase if it is properly used and maintained. If this product proves defective in either material or workmanship, KGI, at its option, will (a) repair the product, or (b) replace the product, at no charge for parts or labor. If the product model is no longer available and cannot be repaired effectively or replaced with an identical model, KGI at its sole option may replace the unit with a current model of equal or greater value.

In some cases, modification to the mounting surface may be required where a new model is substituted. KGI assumes no responsibility or liability for such modification. To obtain a repair or replacement under the terms of this warranty, please return to the dealer first, if possible, and the dealer will direct you accordingly for repairs or replacement. You will be required to submit a copy of the original receipt. Return shipping for exchanges/repairs is the sole responsibility of the original retail purchaser.

SPECIFICATIONS

• Bluetooth 5.0
• A2DP Codecs: SBC, aptX®, AAC
• Range: up to 10m (33 ft.)
• Charging Case Input Rating: 5V DC, 0.5A

REFERENCE LINK

https://support.klipsch.com/hc/en-us/articles/4406589299348-T4-True-Wireless-Pairing-