Table of contents
show
Locky USA 2230 Keyless Latch Mechanical Lock User Manual
Get Started
Step 1: Change User Code (OPTIONAL)
If you wish to change your code, see instructions on reverse side.
Step 2: Prep Door for Installation with Template
- Place template (supplied) on door and fold along door’s edge.
- Mark holes for 2 3/8” or 2 3/4” backset.
- Drill holes as instructed.
NOTE: For Pre-Prepped 2 1/8” doors, you only need to drill top hole.
Step 3: Adjust Latch (if necessary) & Install
- Adjustable latch (#3) is factory preset for a 2 3/8” backset.
- For 2 3/4” backsets, slide the Cam assembly on the latch to 2 3/4”.
- Insert latch into door and secure with Wood Screws (#11).
Step 4: Install Support Pin & Hex Bolts
- Install Brass Support Pin (#14) into either hole on Outside Body as shown in the figure to the Right.
- Install/screw Hex Bolts into the top and bottom of the Outside Body as shown in the figure.
Step 5: Verify Correct Spindle Length
- With latch (#3) installed, hold the Inside Body (#2) and Rubber Trim Plate (#4) to the door.
- Place Spindle (#7/8) through latch, into the Inside Body, as far as possible.
- Spindle should extend from exterior of door 3/8” min. – 5/8” max.
- If the 30-45 mm (#8) is too long, cut it to the correct length.
IMPORTANT: If spindle extends less than 3/8” it may not engage the lock. If spindle extends more than 5/8”, it will cause the lock to bind.
Step 6: Determine Knob Turn Direction (to unlock)
- The lock is preset to unlock when turned clockwise after combination is entered.
- If desired, you can unlock the door with a counter-clockwise turn. Remove the two blue screws and move the pin to the opposite side as shown. *2230 DC – Inside Body pin must on opposite side from Outside Body.
Step 7: Install the Lockey 2230/2435
- Place the Rubber Trim Plate (#3) on the backside of the Outside Body (#1).
- Place the Outside Body on the door. The hexagonal bolts should extend into the top and bottom holes.
- The Support Pin (#14) on the Outside Body should fit into and extend through the hole in the Latch (#3). INSTRUCTIONS CONTINUED ON REVERSE SIDE
- Insert the Spindle (#7/8) into the Outside Body (#1) ensuring it’s in the proper angled position. *(SEE FIGURES BELOW)
- Using a screwdriver, secure the lock to the door with the Screws (#9 or #10). Screw length is dependent on door thickness.
- Test the operation of the Latch by turning the inside knob/lever.
- Locate position where Latch strikes door frame and install Mortised Strike (#5) and Strike Plate (#6).
IMPORTANT: SPINDLE POSITION/ANGLE
- CLOCKWISE TURN TO UNLOCK WITH COMBINATION
The 2230/2435 is factory preset to unlock with a clockwise turn when the combination is entered. The Spindle MUST be placed through the latch, at a 10:00 – 4:00 angle as shown. - COUNTER-CLOCKWISE TURN TO UNLOCK WITH COMBINATION
If desired, the 2230/2435 can be unlocked with a counter-clockwise turn when the combination is entered. To unlock the 2230/2435 with a counter-clockwise turn, please refer to Step 6 to change the Handing Pin. After changing the Handing Pin, the Spindle MUST be placed through the latch at a 2:00 – 8:00 angle as shown.
How To Change Code
- Using a #2 screwdriver, remove the four (4) Red Screws.
- Carefully remove cover plate.
WARNING: Springs are attached to plate.
- PRESS & HOLD ‘C’ BUTTON to release tumblers.
IMPORTANT: ‘C’ Button must be pressed and held down when removing and inserting tumblers. Failure to do so will damage the lock and void the warranty
- While holding the ‘C’ BUTTON, remove/add CODE (Red) and NON-CODE (Blue) Tumblers to create your desired code. Ex: 3 Red = 3-Digit Code / 6 Red = 6-Digit Code
IMPORTANT: Ensure notched side of tumbler fits into slot. (Below – Far Right). - After changing your code, release the ‘C’ BUTTON to secure the tumblers in place.
- Replace the cover plate and secure with four (4) Red Screws, using a #2 screwdriver.
- TEST CODE before installing/re-installing lock.
REFRENCE LINK
