Table of contents
show
AGLUCKY HZB-12-230V Ice Maker Machine User Manual
PREPARING YOUR ICE MAKER FOR USE
Your safety and the safety of others are very important. We have provided many important safety messages manual and your appliance. Always read and obey all safety messages. This is the safety alert symbol:
WARNING
These words mean: You can be killed or seriously injured if you don’t immediately follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed. When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property. Read all instructions before using any appliance.
- Do not operate this, or any other appliance with a damaged cord. If the supply cord is damaged, it must be replaced by the manufacturer its service agent, or a similarly qualified person to avoid a hazard. This ice-maker must be positioned so that the plug is accessible. Connect to properly polarized outlets only. No other appliance should be plugged into the same outlet. Be sure that the plug is fully inserted into the receptacle.
- Do not run the power cord over carpeting or other heat insulators. Do not cover the cord. Keep the cord away from traffic areas, and do not submerge it in water.
- We do not recommend the use of an extension cord, as it may overheat and become a risk of fire. If you must use an extension cord, use No. 14AWG minimum size and rated no less than 1875 watts.
- Unplug the ice maker before cleaning or making any repairs or servicing.
- Exercise caution and use reasonable supervision when the appliance is used near children.
- Do not use your ice maker outdoors. Place the ice-maker away from direct sunlight and make sure that there is at least 4 inches of space between the back of your unit and wall. Keep a minimum distance of 4 inches on each side of your unit free.
- Do not use other liquids to make the ice cube other than water.
- Do not clean your ice maker with flammable fluids. The fumes can create a fire hazard or explosion.
- Do not tip over.
- If the ice maker is brought in from outside in wintertime, give it a few hours to warm up to room temperature before plugging it in.
GETTING TO KNOW YOUR UNIT
General instruction
- Ice scoop.
- Ice full sensor
- Ice basket
- Top cover with transparent window
- Air exhausting
- Water drain cap: at front bm side of the unit.
- MAXIMUM WATER LEVEL:-A –
Remove the ice basket, you can see the water level mark.
OPERATING PROCEDURES & MAINTENANCE
Position of control panel & function
Control Panel:
Easy to use. visible functions touch display setting.
- A. Selected ice size displaying: Small and Large.
- B. Power indicator
- C. Ice-Full indicator
- D . Water shortage indicator
- E. Button to turn on/off the unit.
- F. Button to select ice cube size.
UNPACKING YOUR ICE MAKER
- Remove the exterior and interior packaging. Check if the ice basket and ice scoop are inside. If any parts are missing, please contact our customer service.
- 2. Remove the tapes for fixing the ice shovel, ice basket & ice scoop. Clean the tank & ice basket.
- Put the ice maker on a level & flat countertop without direct sunlight and other sources of heat (i.e.: stove, furnace, radiator). Make sure that there is at least 4 4-inch gap between the back & LH/RH sides with the wall.
- Allow one hour for the refrigerant fluid to settle before plugging the ice maker in. 5. The appliance must be positioned so that the plug is accessible. WARNING: fill with potable water only. Only use drinking water.
DANGER
Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged please call our customer service.
- This unit should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug which mates with standard three-prong wall outlets to minimize the possibility of electric shock.
- Plug your appliance into an exclusive, properly installed, grounded wall outlet. Do not under any circumstances, cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician.
- This appliance requires a standard 110-120volt, 60Hz electrical outlet with three-prong ground.
CLEANING AND MAINTAINING YOUR ICE MAKER
Before using your ice maker, it is strongly recommended to clean it thoroughly.
- Take out the ice basket.
- Clean the interior with diluted detergent, warm water, and a soft cloth.
- Then use the water to rinse the inside parts, and drain out the water by unplugging the drain cap on the front bottom side.
- The outside of the ice maker should be cleaned regularly with a mild detergent solution and warm water.
- Dry the interior and exterior with a clean soft cloth.
- When the machine is not to be used for a long time, drain water completely & dry the interior.
USING YOUR ICE MAKER
- Open the cover, remove the ice basket, and pour water into the tank. Keep the water level below the water level mark.
- Press the “Power” button on the control panel to begin the ice-making cycle.
- Select the ice cube size by pressing the “Select” button. If the room temperature is lower than 60°F, it is recommended to select a small ice cube to avoid ice sticking together.
- The ice-making cycle lasts approx. 6 to 13 minutes, depending on the selection of ice cube size and the room temperature. The recommended room temperature is 50°F to 105 °F
- If the water pump can’t inject water, the ice maker will stop automatically, and the “Add Water” indicator will be on. Press the “Power” button, and fill the water up to the max. water level mark and press the “Power” button again to turn on the unit again. Allow the refrigerant liquid inside the compressor at least 3 minutes to settle before restarting
- The ice maker stops when the ice basket is full and the “Ice” indicator will be on. Warning: Direct sunlight or sunlight reflection may cause infrared sensor malfunction. If the unit doesn’t stop even if the ice cubes obstruct the sensor, move the unit where no sunlight.
- Change water in the water reservoir every 24 hours to ensure a reasonable hygiene level.
TECHNICAL PARAMETERS & CIRCUIT DIAGRAM
EXPLOSIVE DRAWINGS
