LocklyVision PGD798 Deadbolt Edition Video Smart Lock User Manual
Preparation
To complete the installation you will need:
- The lock contains electrostatic-sensitive (ESD) parts. Best practices: ground yourself by touching a metal surface other than lock to discharge any ESD you might have; don’t wear clothes prone to static (ESD); avoid touching electronic internal pins and circuit board.
ADJUST DEADBOLT AND INSTALL
Step 1
- The deadbolt defaults to 2-3/4 “(70mm) backset which is measured from the center of the door hole to the door edge. If the deadbolt slot is aligned to the center of the door hole, proceed to skip the following steps and proceed to the next page.
- If the deadbolt slot is not aligned to the center of your door hole, adjust deadbolt to 2-3/8″ (60mm) backset. Refer to the following steps to adjust the deadbolt:
- Extend the deadbolt by inserting a flat-head screwdriver into the slot and turning clockwise.
- Insert the deadbolt into the door edge, make sure that the right side is up and the slot is in the vertical position. Secure with 2 screws.
INSTALLING EXTERIOR ASSEMBLY (B)
Step 2
- Check the exterior assembly B alignment to door hole and deadbolt before peeling off film on adhesive strips.
- Peel film from adhesive strips and make sure torque blade is in the vertical position with the deadbolt extended. Place assembly and torque blade through the deadbolt slot and guide connection cables through the cross-bore hole under the deadbolt as shown. Complete mounting by aligning and securing until flush to exterior door surface.
INSTALLING INTERIOR ASSEMBLY (G
Step 3
- Check interior mounting plate D alignment to your door hole before securing with adhesive strips.
- Align and secure mounting plate with adhesive strips. Guide connection cables through the hole and secure to the lower left notched hole.
- Insert and tighten by hand 2 screws located on the left and right of the blade. Check alignment and tighten with screwdriver until mounting plate is securely placed on door
- Use the key to ensure deadbolt locks and unlocks smoothly (no binding or rubbing).
IMPORTANT: when finished, leave the deadbolt extended and remove the key before proceeding to the next step.
- when installing screws by hand, turn screws clockwise several turns then counterclockwise one turn to ensure smooth threading and no cross threading.
- Plug the larger cable coming through mounting plate D into the interior assembly G as shown. Tuck cable under eyelet hooks and route to the right on interior assembly G .
- Before placing the interior assembly onto the mounting plate, ensure the thumb turn is vertical.
- Place the interior assembly against the mounting plate and make sure the torque blade is inserted to the thumb turn shaft.
- Secure the interior assembly to mount plate door with 2 screws.
INSTALLING BATTERIES
Step 4
- With door open and deadbolt fully extended, place ribbon inside compartment and insert 8 batteries (note correct -/+ polarity).
- After all batteries are installed, PRESS and HOLD the program button for 10S. The lock will automatically start self-check (release program button once check starts). The self-check process determines right or left swinging door and is very important to ensure correct installation.
IMPORTANT: if lock is not properly installed it will open and close repeatedly (refer to next page #3).
- Once self-check completes ensure the lock operates smoothly by manually locking and unlocking the door using the thumb turn on the interior assembly. The deadbolt should operate smoothly without any interference or binding. If necessary, repeat step 2 and ensure that (a) the deadbolt was extended and (b) the torque blade was inserted vertically while the deadbolt was extended.
- Swipe your hand across touchscreen. The lock shouldclose (lock). If the touchscreen is ON, touch , the lock should lock as well. If deadbolt bounces back or unlocks automatically it means something is not installed correctly. Go back and repeat step 2, same as above.
- Once self-check is complete, install battery cover I and secure with screw on top (do not over tighten).
INSTALLING STRIKE PLATE
Step 5
Use the supplied door strike plate L which has the built-in door sensor magnet.
Because doors and frames vary in design it may be necessary to make slight adjustments to your strike plate and/or dust box in order to ensure smooth deadbolt operation. This is very important. If the deadbolt is binding or catching in any way, the lock will beep rapidly, indicating it cannot close due to misalignment and/or excessive rubbing or binding.
PAIRING VISION CONNECT WITH LOCK
Step 6
To enable video doorbell, live monitoring and voice control with Amazon Alexa or Google Assistant-enabled devices. you will need to setup the included Vision Connect WI-Fi hub and pair it with the Lockly VisionTM deadbolt smart lock + video doorbell.
Vision Connect stores recorded video on the included TF card. Although the TF card is discrete, it is recommended to locate it in a discrete or secure area to protect your privacy and video recordings. TF Card is already inserted on the hub when shipped.
LOCKLY APP & UNIQUE ACTIVATION CODE
Before connecting Vision Connect Hub download the Lockly app on your smartphone. It’s required to finish setup and to set (pair) the connection between hub and lock.
- Additionally, you’ll need the Activation Card with unique pre-paired QR code to your lock.
- The card is located in the packaging that your lock came in. This QR code can also be found at the bottom of Vision Connect Hub.
- Please keep it in a safe place—this QR code is required to complete the setup and will be required if you lose your smartphone or access code.
APP SET UP
Set up an account by registering your Lockly VisionTM in the Lockly app. Registration is also mandatory to activate your locks warranty.
After successful registration, select “add a new device” (you can also get to this from the menu in the top left), select Vision, and follow the step-by-step on screen instructions. You can also reference these steps on following pages.
LOCATION GUIDELINES
The Vision Connect Hub connects directly to your Wi-Fi router using the provided LAN cable. Choose an appropriate location for the hub for optimum performance (see below). For optimum connectivity, it is recommended that the hub be no further away from the lock than 100 feet, placed 3 feet (1 meter) off the ground.
During the setup process position yourself between the lock and the Vision Connect hub—ideally no more than 100 feet (30 meters) apart. Ensure your iOS or AndroidTM device has both Bluetooth® and Wi-Fi enabled,
- Sometimes distances between hub and lock can vary due to circumstances.
- If you are having difficulty setting up optimal range of 100/ft or less, we’re here to help. Call our customer care team: (669) 500 8835, or visit Lockly.com/help for suggestions and troubleshooting tips.
VISION CONNECT HUB SETUP
Step 7
- Ensure the TF card that comes with Vision Connect is properly inserted.
- Connect LAN cable to closest Wi-Fi router to the Lockly VisionTM lock (<100ft).
- Connect power cable and plug USB power adapter into outlet.
- Wait 2 minutes for hub to self calibrate.
- Once LEDs turn RED and blink yellow.
Vision Connect is now ready to connect to your iOS or AndroidTM device.
PAIR VISION LOCK TO APP
Step 7
Launch the Lockly App and select “add a new device”, then select Vision. You will be prompted to scan the QR code from the Activation Card or Vision Connect Hub (located at the bottom).
- Make sure your Lockly VisionTM Elite has the latest firmware. Allow updates and follow instructions if prompted. For more info, visit: http: //www.support.Lockly.com/faq/firmware-update/
- Power interruption during firmware update may damage the Vision Connect hub. Do not interrupt or turn the power off while firmware update is in progress.
TIPS
- Remember to register for warranty.
- Allow your mobile phone to receive push notifications.
- Send in-app feedback if you encounter any issues while using the App.
- If you are having difficulty scanning the QR code, we’re here to help. Call our customer care team: (669) 500 8835, or visit Lockly.com/help for suggestions and troubleshooting tips.
VISION CONNECT STATUS & TROUBLESHOOTING
VOICE CONTROL
Hands-free voice control
Control and check your status using only your voice with Amazon Alexa or Google Assistant-enabled devices.
In Google Home or Amazon Alexa app, add Lockly skill for Alexa or Lockly Action on Google, then follow on screen instructions. See full list of commands, help videos, or troubleshooting your Lockly at https://Lockly.com/help
FCC Warning：
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
REFRENCE LINK
