LocklyVision PGD7S 7S Smart Deadbolt Lock User Manual

LocklyVision PGD7S 7S Smart Deadbolt Lock User Manual

OVERVIEW AND PARTS LIST

• A. Keys
• B. Exterior Assembly
• C. Exterior
• D. Mounting Plate
• E. PM5 Screw
• F. Interior Assembly
• G. PM5×60mm Screw
• H. Battery Cover
• I. PM4*12MM Screw
• J. Deadbolt
• K. KA4*20MM Screw
• L. Strike Plate
• N. Dust Box
• U. Activation Card

Preparation

To complete the installation you will need:

ADJUST DEADBOLT

1. Deadbolt slot must align to the center of the door hole. Adjust as shown if needed.
2. The deadbolt comes set to 2-3/4″ (70mm). Adjust length to 2-3/8” (60mm) if necessary. (wear gloves to protect from possible pinching).
3. Extend the deadbolt by inserting a flat-head screwdriver into the slot and turning clockwise.
4. Insert the deadbolt into mortise flush with door edge, make sure that the right side is up and the slot is in the vertical position. Secure with 2k screws.

INSTALLING THE EXTERIOR ASSEMBLY

Step 1

1. Check the exterior assembly (B) alignment to door hole and deadbolt before peeling off film on adhesive strips.

1. Peel film from adhesive strips and make sure torque blade is in the vertical position with the deadbolt extended. Place assembly and torque blade through the deadbolt slot and guide connection cables through the cross-bore hole under the deadbolt as shown.

Step 2

1. Check interior mounting plate (K) alignment to your door hole before securing with adhesive strips.
2. Align and secure mounting plate with adhesive strips. Guide connection cables through the hole and secure to the lower left notched hole.
3. Insert and tighten by hand 2 screws located on the left and right of the blade. Check alignment and tighten with screwdriver until mounting plate is securely placed on door.
4. Plug the cable coming through mounting plate into the interior assembly as shown. Tuck cable under eyelet hooks and route to the right on interior assembly .

INSTALLING BATTERIES

1. With door open and deadbolt fully extended, place ribbon inside compartment and insert 4
   batteries (note correct -/+ polarity).
2. After all batteries are installed, PRESS and HOLD the program button for 10 S. The lock will automatically start self-check (release program button once check starts). The self-check process determines right or left swinging door and is very important to ensure correct installation.
3. Once self-check completes ensure the lock operates smoothly by manually locking and unlocking the door using the thumb turn on the interior assembly. The deadbolt should operate smoothly without any interference or binding. If necessary, repeat step 2 and ensure that (a) the deadbolt was extended and (b) the torque blade was inserted vertically while the deadbolt was extended.
4.  Swipe your hand across the touch screen keypad, the lock should close (lock). If deadbolt bounces back or unlocks automatically it means something is not installed correctly. Go back and repeat step 2, same as above.
5. Once self-check is complete, install battery cover (H), secure with screw on top (do not over tighten).

DOOR STRIKE

Use the supplied door strike or use your existing as long as deadbolt operates smoothly without binding or catching۔

IMPORTANT: because doors and frames vary in design it may be necessary to make slight adjustments to your strike plate and/or dust box in order to ensure smooth deadbolt operation.

DOWNLOAD LOCKLY APP

Congratulations! You have completed the Lockly Model 7S physical lock installation. To complete your setup, download the Lockly app from the App Store or on Google Play and follow below on-screen instructions.

FCC STATEMENT

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•  Consult the dealer or an experienced radio/TV technician for help.

REFERENCE LINK

https://lockly.co.nz/