Klim Ai-1 Rally Airbag Vest User Manual
INTENDED USE
The IMP Moto back and the IMP back 1 protector was designed to be used uniquely on motorbikes. Do not use for any other application (skiing, skating, horseback riding, cycling, etc.) The back protector protects against impacts with the ground or an obstacle during an accident. It may reduce injury severity (contusions or fractures). No product or protection system can offer total protection against injuries or damages to an individual or an asset in the event of fall, collision, impact, loss of control, or other. Likewise, this back protector may not totally prevent injuries to the spinal column. The back protector does not offer protection against the risks of perforation, cut or penetration of an object. Use of this product must not encourage exceeding any limits or taking additional risks.
FITTING THE VEST
The vest must be worn and fitted correctly so that the protection areas are placed on the thorax, abdomen and back. To obtain optimum protection and comfort, please select the right size and ensure that the vest is fitted correctly to your body. Close all the closures and other straps for maximum comfort. If necessary, refer to the following table to select the appropriate size for your body shape:
SIZING SELECTION
Refer to the table below to choose your size:
- Selecting a protector that is too large may lead to a risk of interference with the helmet, causing dangerous driving conditions.
| Back protector | Size 1 | Size 2 | Size 3 |
| Waist-shoulder length | |||
| 37-42 cm | 40-45 cm | 42-47 cm |
Fit Instructions
The IMP moto back 1 and the IMP moto back protector must be correctly fitted and worn, in order to effectively protect the protection areas. To obtain optimum protection and comfort, please select the right size and ensure that the airbag product is fitted correctly to your body. Close all of the closures (zip closures), and other straps for maximum comfort. The IMP back 1 protector is compatible with pocket of size 25*46 for size 1, 26*48 cm for size 2 and 28*50 cm for size 3.
4 MINIMUM DIMENSIONS IN THE PROTECTION AREAS
Figure 1 – Full back protector Dimensions of the minimum protection area on the back protector
| Dimensions of Figure 1 | |||||
| A | B | C | D | E | F |
| 72% | 29% | 44% | 29% | 32% | 25% |
| NOTE: All dimensions are related to the waist-shoulder length (100%) of the largest user. | |||||
USE AND STORAGE INSTRUCTIONS
The back protector must be used and store exclusively at temperatures between -10°C and 45°C (14°F and 113°F). Prolonged exposure of the system to temperatures exceeding this range may compromise its functionality. Keep the
back protector in a clean area and away from humidity. Transport the back protector in clean packaging protecting it from humidity. After an impact, the back protector may be partially damaged by having absorbed the energy from the impact to reduce its force. Systematically check your protection equipment before use to confirm that it is in good use able condition and not damaged. If you suspect any deterioration, contact your local reseller. Do not, under any circumstances, modify your back protector nor its components. Any modification of any kind may compromise its
functions and, consequently, its protection performances in case of a fall or accident. Do not repair or replace with any other parts or accessories which is not an original In&motion item. To clean the back protector, use a soft wet cotton cloth on the foam or plastic part.
- Do not bleach
- Do not iron – Do not machine wash
- Do not dry clean – Do not tumble dry
- Do not use a hair dryer – Do not use detergent
PRODUCT RECYCLING
At the end of this product’s life, please dispose of this product separately in accordance with your local laws and regulation. For more information on the separate collection systems for waste electrical and electronic equipment that are available for consumers, near your home, free of charge, please contact your local municipality authority. Do not discard a full inflator (that has never been triggered). To dispose of a full inflator in case of it is out-of-date, please refer to www.inemotion.com.
STORAGE AND TRANSPORTATION
Keep the vest and the In&box in a clean and ventilated area, away from humidity and light, and away from impacts and pressure. Do not store the vest and the In&box near combustible surfaces or objects. Do not leave the vest exposed to direct sunlight, under a windscreen, store in a car, or in a top case.Do not fold, crease, bend, twist, or ball up the vest. Hang it on a hanger or in a completely flat position to avoid any rupture or breakage. Transport the vest in clean packaging protecting it from humidity and direct sunlight. Make sure to turn your In&box off when using any other transportation (car, bus, airplane, train or using a motorcycle but not wearing the airbag system) and keep this user manual for as long as you have the vest and transfer the user manual to any subsequent owner of the vest. Furthermore, keep this user manual with the product when travelling, notably by airplane.
PRODUCT INSPECTION
After an impact, the back protector, the airbag system and in particular the airbag cushion, may be partially damaged by having absorbed the energy from the impact to reduce its force. Time can also partially damage your product. Systematically before every use check visually your protection equipment to confirm that it is in good useable condition and not damaged:
- No fabric deterioration (excessive bubbling, snags, fraying seams, broken seams, over-stitching)
- No deterioration of the plastic parts (fissures, cracking, whitening).
“This product should only be serviced/repaired by KLIM to guarantee the full functionality of this product. Under no
circumstances should the vest be modified or disassembled.” “Follow local regulations for recycling/discarding the vest and back protector.” The vest life cycle is variable. It depends on the frequency and conditions of use. Used and maintained correctly, the vest is guaranteed 2 years starting from the date of purchase. After that, if you have any suspicion, you can have your airbag vest controlled by KLIM.
USING THE IN&BOX
To start:
For the first use of your product, please read the detailed In&box user instructions in the In&motion user manual, provided with the In&box.
Insert your In&Box into position.
The arrows indicated on the In&box lock open (up and down) must be aligned with the INSERT arrows indicated on the shell. Using the lock, push the In&box to the left side to clip it into place. The arrows indicated on the In&box lock closed must be aligned with the INSERT arrows indicated on the shell.
CLEANING INSTRUCTIONS
Do not wet the back protector or the back of your item. The inflator connector, the inflator, the In&box must not encounter water. Clean the exterior and interior of your item with soapy water using a small soft brush and by gently scrubbing in a circular motion. Then rinse with a soft wet sponge to remove the excess soap and any dirt that you may have loosened in the previous step. Dry your item first by using a soft cotton cloth; then leave to completely air
dry in a dry and ventilated area for a minimum of 12 hours.
- Do not bleach
- Do not iron
- Do not machine wash
- Do not dry clean
- Do not tumble dry
- Do not use a hair dryer
- Do not use detergent
- Dry away from sources of heat and away from sunlight
JACKET COMPATIBILITY
The In&motion airbag system is compatible with a backpack. For that, it is important to respect the following conditions:
- The total weight of the bag must not exceed 8kg,
- The use of support straps in the abdomen and chest is prohibited,
- The shoulder straps must not hinder the deployment of the airbag. When pulling the straps forward, there should be a distance of 10 cm between them and the front of the shoulder.
- The backpack must be worn on the back of the user’s body, compatible with a compatible motorcycle jacket.
The airbag product is not compatible child harness. The airbag product is not compatible with jackets or coats having
a support in the crotch. Never wear a neck brace while wearing the airbag system. The airbag system is not compatible with a neck brace. The vest is not compatible with full one-piece suit (for instance textile/leather suit, rain suit) except “In&motion Airbag system compatible” suits which have been tested and are compatible
with a proper inflation of the airbag, provided that the size of the garment is appropriate to your body dimensions.
TROUBLESHOOTING
If you have a problem concerning the vest, the airbag system or you do not know where the problem is coming from, contact your local reseller. If you have a problem concerning the In&box, contact In&motion customer service via the contact form in the contact section of the www.inemotion.com website.
