Black decker BV3600 Electric Blower Manual
SAVE THESE INSTRUCTIONS
Safety Rules and Instructions: Extension Cords
Double-insulated tools have 2-wire cords and can be used with 2-wire or 3-wire extension cords. Only round-jacketed extension cords should be used, and we recommend that they be listed by Underwriters Laboratories (U.L.) (C.S.A. in Canada). If the extension will be used outside, the cord must be suitable for outdoor use. Any cord marked as outdoor can also be used for indoor work. An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and to prevent loss of power and overheating.
The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. Before using an extension cord, inspect it for loose or exposed wires, damaged insulation, and defective fittings. Make any needed repairs or replace the cord if necessary. To determine the minimum wire size required, refer to the chart:
Functional Description
- Powerhead
- Upper blow tube
- Lower blow tube
- Concentrator
- Upper vac tube
- Lower vac tube
- Shoulder bag
ASSEMBLY FOR BLOW MODE
WARNING: Before attempting any of the assembly steps below, ensure the product is switched off and disconnected from the power supply.
BLOW TUBE ASSEMBLY
- Ensure the grill cover is attached to the power head. If not, attach the cover as shown in the inset of figure 1. NOTE: The unit will not operate in blow mode without the grill cover in place. Align the upper and lower tubes as shown in figure 1.
- Push the lower tube firmly into the upper tube, until the tubes click into place.
- Blow tubes must be assembled to the power head before use.
- Never operate without both lower and upper tubes assembled.
- In the interest of safety, it is not intended for the tubes to be separated once assembled.
- Push the tube assembly onto the power head until it is in the fully locked position.
- Use the air concentrator attachment to target airflow to a tighter area. Add the attachment to the assembly as shown in figure 3. Push on until the hole in the tab engages raised post on the tube.
MAINTENANCE
CLEANING AND STORAGE TURN OFF AND UNPLUG THE TOOL!
(Unplug the extension cord at the power source.) Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool in a liquid. Clean out any clippings which may have accumulated in the Blower/Vac. When used properly with dry leaves the fan chamber of your Blower/Vac should remain clean.
If damp earth and debris are ingested some of the particles may build up on the inside of the fan chamber. If this happens the performance of the unit will decrease. This area can be cleaned out using a wooden stick as shown in figure 13 after disconnecting from the power source. Your Blower/Vac should be stored in a dry place.
BLOW MODE
- Hold the blow tube approximately 7 inches (180mm) above the ground, turn the blower/vac on, and using a sweeping motion from side to side, advance slowly keeping the accumulated debris/leaves in front of you.
- Once you have blown the debris/leaves into a pile, you can convert to vacuum mode to collect the debris.
- Using the air concentrator will help remove matted debris and leaves.
- To use the cord retainer as shown in figure 10B, loop the extension cord over the power head cord and plug the two ends into each other. Then hook the extension cord under the retainer
- To use the cord retainer as shown in figure 10A, hook the extension cord under the retainer. Then plug the cord from the power head into the extension cord.
WARNING:
SHOCK HAZARD. DO NOT POUR OR SPRAY WATER ON THE TOOL IN AN ATTEMPT TO CLEAN IT. Do not store the tool on or adjacent to fertilizers or chemicals. Such storage can cause rapid corrosion of the metal parts.
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under “Tools— Electric” or call: 1-800-544-6986 or visit www.blackanddecker.com
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways. The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailerʼs policy for exchanges (usually 30 to 90 days after the sale).
Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. The second option is to take or send the product (prepaid) to a Black & Decker-owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker-owned and authorized Service Centers are listed under “Tools-Electric” in the yellow pages of the phone directory. This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province.
Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use. FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement. LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, check country-specific warranty information contained in the packaging, call the local company, or see the website for warranty information.
