Monster All-In-One Public Address Speaker User Manual

Monster All-In-One Public Address Speaker User Manual

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure.

CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different form that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, Human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

UNPACKING

Check that you have all of the following items. If any item is missing, please contact the customer service hotline for assistance. The hotline number is printed on the cover page of this user manual.

• Monster Rockin’ Roller Party
• AC Power Cable
• Wired Microphone
• Telescoping Tripod Speaker Stand
• User Manual (with Warranty Statement)
• Quick Start Guide

IMPORTANT SAFETY INSTRUCTIONS

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADE SCAN BE FULLY INSERTED TO PREV- ENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOIST.

• READ INSTRUCTIONS – All the safety and operating instructions should be read before the product is operated.
• RETAIN INSTRUCTIONS -The safety and operating instructions should be retained for future reference.
• HEED WARNINGS – All warnings on the product and in the operating instructions should be adhered to.
• FOLLOW INSTRUCTIONS – All operating and use instructions should be followed.
• CLEANING – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners Clean only with a dry cloth.
• ATTACHMENTS – Do not use attachments not recommended by the product manufacturer as they may cause hazards.
• ACCESSORIES – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only. with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer instructions, and should use a mounting accessory recommended by the manufacturer. A product and cart combination should be moved care-quick stops, excessive force and uneven surfaces may cause the product and cart combination to overturn.
• VENTILATION- Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation, such as a bookcase or rack, unless proper ventilation is provided or the manufacturer*instructions have been adhered to.
• POWER SOURCES – This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
• GROUNDING OR POLARIZATION – This product may be equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature: If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
• POWER-CORD PROTECTION – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point of exit from the product.
• NON-USE PERIODS – The power cord of the product should be unplugged from the outlet when left unused for long periods of time.
• Do not use this apparatus near water.
• Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power – supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
• Mains plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely.
• Battery shall not be exposed to excessive heat such as sunshine, fire or the like.

CONTROLS AND CONNECTIONS

Power ON/OFF Switch:

Toggle switch to ON position:

• Green power LED Indicator light and LED Display will power on.
• The unit voice promp will say, “Power on.”
• Automatically enters into Bluetooth® pairing status
  Toggle switch to OFF position:
• All LED Indicators and LED Display will turn off.
• The unit voice promp will say, “Power off,” before powering down.

BT (Bluetooth®) Button:

Switch to Bluetooth® Audio Source:

• While in another audio source, press the BT Button to switch to Bluetooth® mode or cycle though audio sources using the source button.
• The unit will automaticelly disconnect from the current device.
  Bluetooth® pair audio device:
• Set unit source to Bluetooth®.
• Long press BT Button for 2 seconds to enter into pairing status.
• Select “MNX6” from your Bluetooth® enabled audio device.
• The unit voice promp will say, “Connected,” when successfully paired.
• The blue Bluetooth® indicator light will remain on.
• If the signal moves out of range the blue Bluetooth® indicator light will blink and disconnect if the connection is not restablished after 5 minutes.
  Disconnnect Bluetooth® audio device connection:
• Set unit source to Bluetooth®.
• Long press BT Button for 2 seconds to enter into pairing status.
• The unit voice promp will say, “Disconnected.”
• The blue Bluetooth® LED Indicator light will begin to flash.
• Unit will enter pairing status.
• The unit voice promp will say, “Pairing.”
  Clear Bluetooth® pairing history:
• Set unit source to Bluetooth®.
• Long press BT Button for 8 seconds to clear information.
• Unit will enter pairing status.
• The unit voice promp will say, “Pairing.”
• The blue Bluetooth® LED Indicator light will begin to flash.

Play (/Pause) Button:

Play/Pause Button only works with Bluetooth® source:

• While audio is playing, press the Play Button to pause playback.
• While audio is paused, press the Play Button to resume playback.

Master Volume Knob:

Incress overall volume in playback mode :

• Defualt volme level is 10.
• Rotate master volume knob clockwise. The power LED Indicator blinks when the max level of 32 is reached.
• Decrese overall volume in playback mode:
• Rotate master volume knob counter-clockwise. The power LED Indicator blinks when the minimum volume level of 0 (mute) is reached.

Microphone Control:

• XLR & ¼” Ports (Mic 1 and Mic 2):
• Except XLR and ¼” microphones/instrument inputs
• LED display will show the mic icon when a microphone is plugged-in.
• Gain Knob (Mic 1 and Mic 2):
• Rotate the gain knob clockwise to increase or counter-clockwise to decrease the level on each channel.
• Echo Effect Knob:
• Rotate the echo knob clockwise to increase or counter-clockwise to decrease the level on each channel.

Previous & Next (arrow) Buttons:

FM radio source controls:

• LED display FM indicator icon will light up in FM mode.
• Short press the previous or next button to adjust the FM radio frequency shown on LED display.
• Long press the previous or next button to search for radio stations.
• Bluetooth® source controls:
• LED display BT indicator icon will light up in Bluetooth® mode.
• The previous/next buttons will change the audio track.

REPEAT Button:

This function is only available though the USB mode. Short press the REPEAT button to select one of three status settings:

• Repeat ALL (tracks). “ALL” will be showen on the LED display.
• Repeat ONE (track). “ONE” will be showen on the LED display.
• Repeat OFF. “OFF” will be showen on the LED display.

TWS Button (True Wireless Dual Pairing):

TWS pairing (make sure both unit A and B are in close proximity to each other):

• Long press the TWS button to enter into pairing status. The Bluetooth® indicator LED will alternate flashing blue and red.
• Press and hold the TWS button of unit A to enter TWS searching mode while unit B is set to Bluetooth® pairing mode.
• The unit A (TX) Bluetooth® indicator LED will light up purple when connected, while the indicator LED for unit B (RX) will be solid red. The unit voice promp will say, “Synchronized.”
• Disconnect TWS:
• Short press the TWS button.

1-6 Number Button:

Equilizer presets available in BT (Bluetooth®), AUX, USB audio sources.

• Short press a number (1-6) button to set the preset. The LED display will show the selected equilizer setting: “Eq-1, Eq-2, . . . Eq-6.”
• Save and select FM Radio station presets.
• Short press a number (1-6) button to set the preset station. The LED display will show the selected preset: “P1, P2, . . . P6.”
• Long press a number (1-6) button to save an FM radio station as a preset. The LED display will show the saved preset: “P1, P2, . . . P6.”

BASS/TREBLE Buttons:

Bass adjustment in working mode:

• Press the BASS/TREBLE button once to enter bass level status.
• The LED display will show the default setting of “b 00. ”
• Turn the VOLUME knob clockwise to increase or counter-clockwise to decrease levels between -06 to 06.
• Treble adjustment in working mode:
• Short press the BASS/TREBLE button twice to enter treble level status.
• The LED display will show the default setting of “t 00. ”
• Turn the VOLUME knob clockwise to increase or counter-clockwise to decrease levels between -06 to 06.

SOURCE Button:

• Short press the SOURCE button to cycle though the different audio sources: BT (Bluetooth®), USB, AUX, FM (radio).

LIGHTING Button:

• Short press the LIGHTING button to cycle through the 15 available light modes. The LED display will indicate mode number: “L01, L02, L03 . . . OFF.” Modes included: SWIRL–> DANCE–>FOLLOW–>DYNAMIC–>SPIN–>SPARK–>SUNSET–>MOOD–>PACE–>RED–> GREEN–>BLUE–>AMBER–>PURPLE–>TEAL–>OFF
• Long press the LIGHTING button to turn off the RGB LED lights.

BASS Button:

• Press the button to turn on/off the BASS (boost). The LED will display “b on” or “b off.”

XLR Out:

• While in audio sources: AUX-in, BT (Bluetooth®), FM radio, or USB, connect the unit to another active (powered) speaker via the XLR line out.

Technical Specs:

• 600 Watts RMS Audio Power
• Sub-woofer: 15” (inch)
• Passive Radiators
• Bluetooth® 5.0
• Audio File Supported: .mp3, .wma, .wav
• Frequency Response: 3.40Hz–20KHz
• Product Dimensions (L x W x H) Inches:
• Product Dimensions (L x W x H) mm:
• Tweeter: 1” (inch)
• AC Power 100-240 Volt
• THD + Noise: <4.10%
• S/N Ratio: >65dB
• Max SPL: >99dB
• RGB LED Lights

DOWNLOAD PDF LINK

https://manuals.plus/m/214478ba1b0c2c02852cd306fc09ecc080766227b7c51faba3ae476682d3f6ea_optim.pdf