BOBOT A10 Computer Speakers User Manual

BOBOT A10 Computer Speakers User Manual

SPECIFICATIONS

1. Model: Bobtot A10
2. Impedance: 3 Ω
3. Output Power: 5W*2
4. Speaker Type: Dual Speaker
5. Connection: 3.5mm AUX-in & BT
6. Frequency Response: 60Hz-20KHz
7. RGB Lights: 3 models and turn off the light
8. Input Power： USB direct plug (DC 5V, no built-in battery)

Function of the Knob & Button

• –Volume Down Turn left to reduce the volume
• +Volume Up Turn right to increase the volume
• Button (Turn on/off, RGB Lights Mode & BT Mode) Long press to turn on/off Short press to switch from RGB slow breathing– Rhythm Jump-Light off. Double-click to switch from AUX to BT mode.
• Headphone output jack Plug in your headphones and listen to music, movies, and games where and when you want to

Connecting to PC and MAC

1. Your PC will automatically detect the Bobtot A10 when you plug in the USB cable and 3.5mm AUX-in cable. RGB light will be working. You can enjoy the music now.
2. BT connection, double click the button to switch to BT mode. you will hear “dududu”, and search for the BT device named “Bobtot A10” and tap to connect. A prompt will play once the pairing is successful.

Note: If you do not hear any audio playing from the speaker, please check the output device list from the “Sound” setting and set the “Bobtot A10 ” as the output speaker.

Connecting to MP3 / Mobile Phones/ other Audio Devices

You can also connect the speaker to your device via a 3.5mm AUX-in cable or BT mode (double click the

button to BT mode and search for “Bobtot A10”).

Note: 

1. The Bobtot A10 speaker is USB powered.
2. Plug the USB into your power bank (not supply) and 3.5mm AUX into your audio device, and the A10 speaker is ready to enjoy the music, no need to turn it on separately.

Wireless Connection via BT

1. Power the speaker: Plug the USB power cable into the power source (USB port of Computer/Laptop/Power Bank/USB Power Adapter ), the RGB light’s on.
2. Double-click the button to switch from AUX to BT mode, the sound prompt is “du du du”
3. Search for the BT device named “Bobtot A10”, and tap to connect, you will hear a sound prompt “connected”. You can enjoy the music now.

Note: 
If disconnect this device, please click button three times

Troubleshooting

About Sound
If there is no sound response after plugging it into USB port, please make sure:

1. The USB interface of your computer work normally or not?
2. Does the audio driver of your computer sound up to date?
3. Click the “Speaker” icon in the taskbar, and make sure that “Headset (Realtek(R)Audio)” is selected as your computer playback device.

About BT Connection

1. Make sure the BT of the speaker is not connected by other devices.
2. Unplug the 3.5mm AUX-in cable from your device.
3. Delete” Bobtot A10″ memorized on your device, then search for”Bobtot A10″ and connect again.

FCC Requirement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against tharmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used under the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

REFERENCE LINK

https://bobtot.net/Downloads