JALL CH-07 RGB Color Changing Clock User Manual
Objects the package contains
This product is packed in a color box, which contains:
- 1x RGB color changing clock
- 1x 5V 2A adapter
- 1x Type-C data line
- 1x instruction manual
- Alarm 1 switch/setting
- Alarm 2 switch / setting
- Screen brightness adjustment / time setting
- Time display font color switch
- Volume down / next channel on the radio
- Radio switch / automatic channel search
- Volume up / previous channel on the radio
- Snooze / Sleeping companion countdown / Increase or decrease of the setting value / radio FM
Product appearance introduction
- Alarm 1 mode switch
- Alarm 2 mode switch
- Type-C 5V power input
- USB output
- Type-C output
Pre-use setting
Power on for the first time
- Remove the protective film from the mirror surface. Connect the TYPE-C power plug to the input port of the alarm clock. Then connect the USB plug to the adapter. At last plug the adapter into the 100V-240V home socket. As shown in the following figure:
Install the battery
- The alarm clock comes with a pre-installed CR2032 battery, and just pull down the insulation sticker. As shown in the following figure:
Time setting
| 1. Long press the TIME SET button for 2s to enter the time setting • In time setting mode, the number will blink, rotate the SNOOZE button to set “hour”. Then click the TIME SET button to confirm, and enter the “minute” setting, rotate the SNOOZE button to set the current minute. |
| 2. Press TIME SET button to enter 12/24-hour setting • Rotate SNOOZE button to set 12/24 hours. |
| 3. Press TIME SET button to enter week setting • Rotate SNOOZE button to set “week”. When the setting is completed, click TIME SET button to confirm and exit. |
| 4. Press TIME SET button to confirm and exit time setting. |
Alarm setting (take alarm 1 as an example)
Long Press ALARM 1 BUTTON for 2s to enter alarm 1 setting
In alarm setting mode, the number will blink. Rotate the SNOOZE BUTTON to adjust the hour of alarm. Then press ALARM 1 BUTTON to confirm and enter the minute setting. Rotate the SNOOZE BUTTON to adjust “minute”.
Press the ALARM 1 BUTTON to confirm and enter the alarm sound selection
Press the ALARM 1 BUTTON to confirm and enter the alarm sound selection. Rotate the SNOOZE BUTTON to select the alarm sound, which will display S01-S08 (01-08 is the sound level, corresponding to different wake-up sounds).
Press the ALARM 1 BUTTON to confirm and enter the volume adjustment
Press the ALARM 1 BUTTON to confirm and enter volume adjustment. Rotate the SNOOZE BUTTON to adjust the volume, which will display V01-V16 (a total of 16 levels)
Press the ALARM 1 BUTTON to confirm and exit the alarm setting.
Note: the setting of alarm clock 2 is the same as that of alarm clock 1.
Alarm switch
Alarm switch
In the time display state, press ALARM 1 BUTTON / ALARM 2 BUTTON, it will switch on/off the alarm.
User Prompt
Alarm 1 and Alarm 2 operate in the same way.
Alarm mode selection
How to SNOOZE or TURN OFF alarm
After the alarm clock is turned on, the alarm clock will ring at the preset time: when it comes to the setting time of the alarm, it will start to ring and wake you up. When the alarm goes off, you can do the following:
Snooze
- Press SNOOZE BUTTON when the alarm goes off, which will enter “Snooze Mode”. And the screen will show a flickering sleepy icon. The alarm will go off again after 9 minutes. Note: it’s unlimited times that you can enter snooze mode
Stop today’s alarm.
When the alarm goes off / or is in snooze mode, click the button of the corresponding alarm to stop today’s alarm and it will go off on the next day.
When no action is taken
If the alarm goes off for 20 minutes without any operation, today’s alarm will be stopped automatically, and it will go off on the next day.
RGB color-changing mode
In the time display state, press COLORS BUTTON to change the display font color (white, red, green, blue, gradient, magic color, left and right graduality, up and down graduality)
FM radio adjustment
FM switch
- In the time display state, press the RADIO BUTTON to turn on/off the FM radio.
Automatically search the FM radio channel
- After the FM radio is turned on, long press RADIO BUTTON for 2s to enter the FM automatic search mode(search range from 76.0MHZ to 108.0MHZ).
FM radio channel adjustment
- After the FM radio is turned on, long press the VOLUME DOWN BUTTON / VOLUME UP BUTTON for 2s to turn to an up/down radio channel.
FM radio volume adjustment
- When the FM radio is on, click the VOLUME DOWN BUTTON / VOLUME-UP BUTTON to adjust the current radio volume.
Replace the battery
Unscrew the battery cover with a screwdriver, and remove the battery cover. Then put the battery into the battery box, install the battery cover, and tighten the screw.
Trouble Shooting
Can’t charge my cell phone.
Please check the port on the back of the alarm clock. Because power cord connected to the output port can also power the clock, but it may cause unknown errors.
The alarm clock no longer displays anything.
- Please click DIMMER BUTTON to confirm whether it has been adjusted to the lowest brightness before.
What is the line behind the alarm clock? Can I unplug it?
It’s a receiving antenna. It’s used to receive radio signals. Please do not damage the antenna, which will damage the radio function of the alarm clock.
How to turn off the radio function when using the sleep timer function or turning on the radio by mistake?
Please click RADIO BUTTON to turn off the radio.
