Danby-DDW1805W-Portable-Dishwasher-Feature

Danby DDW1805W Portable Dishwasher User Manual

Danby-logo

Danby DDW1805W Portable Dishwasher User Manual

Danby-DDW1805W-Portable-Dishwasher-IMG

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING

WARNING! HYDROGEN GAS IS EXPLOSIVE

Under certain conditions, hydrogen gas may be produced in a hot-water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot-water system has not been used for such a period, before using the dishwasher turn on all hot-water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment -grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed in an accordance with all local codes and ordinances.

WARNING!

Improper connection of the equipment-grounding conductor can result in a risk of electric shock . Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded. Do not modify the plug provided with the appliance? If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

WARNING! PROPER USE

  • Do not abuse, sit or stand on the door or dishrack of the dishwasher.
  • Do not touch the heating element during or immediately after use.
  • Do not wash plastic items unless they are marked dishwasher safe. For unmarked plastic items, check the manufacturer’s recommendations.
  • Use only detergent and rinse additives designed for an automatic dishwasher. Never use soap, laundry detergent, or hand washing detergent in your dishwasher. Keep these products out of the reach of children.
  • Keep children away from the detergent and rinse aid, and from the open door of the dishwasher, as there could still be some detergent left inside.
  • The door should not be left in the open position as this could present a tripping hazard.
  • During installation, the power supply must not be excessively or dangerously bent or flattened.
  • To reduce the risk of injury, do not allow children to play in or on a dishwasher.
  • Do not operate your dishwasher unless all enclosure panels are properly in place. Open the door very carefully if the dishwasher is operating, there is a risk of water spraying out.
  • Do not place any heavy objects on the door when it is open. The appliance could tip forward.
  • When loading items to be washed:
  • Load sharp items so that they are not likely to damage the door seal
  • Load sharp knives with the handles up to reduce the risk of cuts.
  • When using your dishwasher, you should prevent plastic items from coming in contact with the heating element.
  • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a qualified technician to avoid a hazard.
  • Please dispose of packing materials properly.
  • Use the dishwasher only for its intended function.
  • Remove the door to the washing compartment when removing an old dishwasher from service or discarding it.
  • Do not tamper with the controls.

CONTROL PANEL

Danby-DDW1802W-Built-In-Dishwasher-Fig1

  1. Power ON Light: Illuminates when the ON/OFF Button is pressed down.
  2. Rinse Aid Warning Light: Illuminates when the dispenser 6 needs to be refilled.
  3. Salt Warning Light: Illuminates when the water softener needs to be refilled. 8 4 ON/OFF Button: Turns on/off the power supply.
  4. Rapid Button: Only used with cycle “.
  5. Plus Button: Only used with cycle
  6. Door Handle: Pull to open the door.
  7. Washing Program Selector: Turn the dial clockwise to select the desired wash cycle.

DISHWASHER FEATURES

Danby-DDW1805W-Portable-Dishwasher-Fig1

  1. Upper Basket
  2. Spray Arms
  3. Lower Basket
  4. Water Softener
  5. Detergent Dispenser
  6. Main Filter
  7. Cup Shelf
  8. Silverware Basket
  9. Coarse Filter
  10. Rinse Aid Dispenser
  11. Portable Faucet Adapter Assembly
  12. Power Cord
  13. Castors

WASH CYCLE TABLE

Danby-DDW1802W-Built-In-Dishwasher-Fig1

WASH CYCLE ADJUSTMENT BUTTONS

  • Plus Button
    This button (see ” Control panel ” ) is used with the normal cycle where pots and pans have dry, caked-on food. This is not recommended for delicate items as the high temperature could make their surfaces opaque or their decorative colors lighten after repeated washings.
  • Rapid Button
    This button (see ” Control panel ” ) when used with wash cycle 4 (glassware) makes it possible to run the wash cycle at a lower temperature (50 C) and eliminates the drying phase.

WATER SOFTENER

  • There are two ways to reduce the hardness: one way is by using water softener, the other is by using detergent.
  • The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils.
  • The appliance is equipped with a special softener that uses salt specifically designed to eliminate lime and minerals from the water.

Loading the Salt into the Softener

  • Always use salt intended for use with dishwashers.
  • The salt container is located beneath the lower rack and should be filled as follows:

Danby-DDW1802W-Built-In-Dishwasher-Fig1

  • Remove the lower basket and unscrew and remove the cap from the salt container.
  • If you are filling the container for the first time , fill 2/3 of its volume with water.
  • Place the end of the salt filter(supplied) into the hole and introduce about 2kg of salt . It is normal for a small amount of water to come out of the salt container.
  • Carefully screw on the cap.

NOTE:

  • The salt container must be refilled when the salt warning light comes on. Though the salt container is filled, the indicator light may not black out before the salt fully dissolves.
  • If there are spills of salt, a soak program could be run to clean the spills.

Adjusting Salt Consumption

The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used. This is intended to optimize and customize the level of salt consumption.

Danby-DDW1802W-Built-In-Dishwasher-Fig1

Unscrew the cap from the salt container. There is a ring on the container with an arrow on it (see Figure to the side). If necessary, rotate the ring in the counterclockwise direction from the “-” setting toward the “+” sign, based on the hardness of the water being used.It is recommended that adjustments should be made in accordance with the following chart:

WATER HARDNESS

Clarke Degrees dH mmol/l
Selector Position Salt consumption
(gram/cycle)
Auto nomy
(cycles/2kgs)
0~14 0~10 0~1.7 / 0 / 14~36 18~44 1.8~4.4 – 20 60
36~71 45~89 4.5~8.9 MED 40 40
71 89 8.9 + 60 25

DETERGENT DISPENSER

The dispenser must be refilled before the start of each wash cycle according to the instructions provided in the” Wash Cycle Table”. Our dishwashers than conventional dishwashers. Generally, only one tablespoon of detergent is needed for a normal wash load. More heavily soiled items need more detergent. Always add the detergent just before starting dishwasher, otherwise it could get damp and will not dissolve properly.

Amount of Detergent to Use

IF THE WATER ISN’T TOO HARD, YOU MAY ALSO PREVENT THE FORMATION OF DEPOSITS BY ADDING DETERGENT. The amount of detergent needed can vary due to differences in water hardness. To determine the water hardness in your area, contact your local water utility or area water softening company. The harder the water, the more detergent you may need. Remember, you should adjust the amount of detergent you use little by little until you find the correct amount.

Danby-DDW1802W-Built-In-Dishwasher-Fig1

  1. Main Wash Detergent
  2. Dispenser Lid lever
  3. Rinse Aid Level Indicator
  4. Prewash Detergent Compartment
  5. Rinse Aid Compartment
  6. Detergent Compartment Lid

Removing Hard Water Spots From Dishes

  • To remove hard water spots, try the following:
  • Run dishes through a normal wash program.
  • Remove all metal dishware, such as cutlery, pans, etc., from the dishwasher.
  • Do not add detergent.
  • Pour two cups of vinegar into a bowl and set the bowl face up on the lower rack of the dishwasher.
  • Run the dishes through a normal wash program.
  • If this doesn’t work, try the same process with 1 / 4 cup of citric acid crystals instead of vinegar.

Proper Use of Detergent

Use only detergent specifically made for use in dishwashers. Keep your detergent fresh and dry. Don’t put powder detergent into the dispenser until you are ready to wash dishes.

WARNING!

Dishwasher detergent is corrosive! Take care to keep it out of the reach of children

RINSE AID DISPENSER

Danby-DDW1802W-Built-In-Dishwasher-Fig7

  • To open the dispenser, turn the cap to the “open” (left) arrow and lift it out.
  • Pour the rinse aid into the dispenser, being careful not to overfill.
  • Replace the cap by inserting it aligned with “open” arrow and turning it to the “close” (right) arrow.
  • The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes that can leave spots and streaks. It also improves drying by allowing water to “sheet” off the dishes.
  • Our dishwashers are designed to use liquid rinse aids. The rinse aid dispenser is located inside the door next to the detergent dispenser.
  • To fill the dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns completely black. The dispenser holds about 100 ml of liquid rinse aid.
  • Be careful not to overfill the dispenser, because this could cause over sudsing. Wipe away any spills with a damp cloth.
  • Don’t forget to replace the cap before you close the dishwasher door.
  • If you have soft water, you may not need rinse aid as it may cause a white film to develop on your dishes.

Adjusting Rinse Aid Dispenser

Danby-DDW1802W-Built-In-Dishwasher-Fig8

A measured amount of rinse aid is released during the final rinse. As with detergent, the amount of rinse aid needed for your dishes depends on the hardness of the water in your area. Too much rinse aid can result in lather or foaming and can cause cloudiness or streaks on your dishes. If the water in The rinse aid dispenser has six settings. Always start with the dispenser set on ” 1 “. If spots and poor drying are problems, increase the amount of rinse aid dispensed by removing the dispenser lid and rotating the dial to “2”. If the dishes still are not drying properly or are spotted, adjust the dial to the next higher number until your dishes are spot-free. We suggest the setting of “4”.

When to Refill the Rinse Aid Dispenser

When the rinse aid dispenser is empty, the rinse aid warning light (on control panel) will illuminate, indicating the dispenser needs to be refilled. The black dot on the rinse aid dispenser indicated the amount of rinse aid in the dispenser. As the rinse aid diminishes, the size of the black dot decreases. You should never let the rinse aid get below 1/4 full.

Danby-DDW1802W-Built-In-Dishwasher-Fig8

As the rinse aid diminishes, the size of the black dot on the rinse aid level indicator changes, as illustrated below.
Full
3 / 4 full
1 / 2 full
1 / 4 full – Should refill to eliminate spotting
Empty

Loading the Dishwasher Racks

For best performance, follow these loading guidelines. Features and appearance of racks and silverware baskets may vary from your model.

How to use the Upper Rack

The upper rack is designed to hold more delicate and lighter dishware such as glasses, coffee and tea cup and saucers, as well as plates, small bowls and lightly soiled shallow pans. Position the dishes and cookware so that they do not get moved by the spray of water. The upper rack can be adjusted for height by putting wheels of different height into the rails.

Danby-DDW1802W-Built-In-Dishwasher-Fig8

  1. Cups
  2. Small serving bowl
  3. Large serving bowl
  4. Glasses
  5. Saucers
  6. Dish
  7. Plates

How to use the Lower Rack

We recommend that you place large items in the lower rack: pots, pans, lids, serving dishes and bowls, as shown below. It is preferable to place serving dishes and lids on the side of the racks in order to avoid blocking the rotation of the top spray arm. Pots, serving bowls, etc, must always be placed top down. Deep pots should be slanted to allow water flow. The bottom rack features fold down tine rows so that larger or more pots and pans can be loaded.

Danby-DDW1802W-Built-In-Dishwasher-Fig8

  1. Oval platter
  2. Soup plates
  3. Dessert dishes
  4. Dinner plates
  5. Silverware basket

SILVERWARE BASKET

Silverware should be placed in the silverware basket with handles at the bottom: If the rack has side baskets, the spoon should be loaded individually in the appropriate slots. Long utensils should be placed in the horizontal position at the front of the upper rack.

Danby-DDW1802W-Built-In-Dishwasher-Fig8

  1. Forks
  2. Soup spoons
  3. Dessert spoons
  4. Teaspoons
  5. Knife
  6. Serving spoon
  7. Gravy ladle
  8. Serving fork

WARNING! 

Do not let any item extend through the bottom of the basket.

TURNING ON THE APPLIANCE

Starting a wash cycle. . .

  • Make sure that the plug for the appliance is inserted into the wall socket.
  • Make sure that the water supply is turned on to full pressure.
  • Load the dishwasher(see the section entitled, ” Loading the Dishwasher ” ).
  • Pour in the detergent(see the section entitled, ” Salt, Detergent and Rinse Aid ” ).
  • Turn the dial located on the right of the control panel in the clockwise direction until the number or the symbol for the cycle setting is aligned with the reference mark (see the section entitled, ” Wash Cycle Table ” ).
  • Press the ON/ OFF button, and the ON/OFF light will turn on. At this point, the wash cycle will begin.

Cancelling or modifying a wash cycle setting. . .

A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been released, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled ” Loading the Detergent ” ). Press the ON/OFF button, and the ON light will turn off. Rotate the dial in the clockwise direction to the desired cycle setting (see the section entitled ” Starting a wash cycle. . . ” ). Then, turn the dishwasher back on using the ON/OFF button.

At the End of the Wash Cycle

Danby-DDW1802W-Built-In-Dishwasher-Fig13

  • When the dial stops turning and is aligned with the STOP mark(see figure), the cycle has finished .
  • Turn off the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher. Wait a few minutes before unloading the dish washer to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage.

Forget to Add a Dish?

  • A forgotten dish can be added any time before the detergent cup opens.
  • Pull the door handle.
  • Do not open the door until the water spray action stops. Steam may rise out of the dishwasher.
  • Add forgotten dishes.
  • Push the door to close . When the door is properly closed, a click will sound.

FILTERING SYSTEM

For your convenience, we have placed the drain pump and filtering system within easy reach inside the tub. There are three components of the filtering system: the main filter, the coarse filter, and the fine filter.

Danby-DDW1802W-Built-In-Dishwasher-Fig14

  • Main filter
    Food and soil particles trapped by this filter are pulverized by a special jet on the lower spray arm and washed down the drain.
  • Coarse filter
    Larger items, such as pieces of bone or glass, that could clog the drain are trapped in the coarse filter. To remove an item caught in this filter, gently squeeze the tabs on top of this filter and lift it out.
  • Fine filter
    This filter holds soil and food residue in the sump area and prevents it from being redeposited on the dishes during a cycle.

CARING FOR THE DISHWASHER

  • To clean the control panel use a lightly dampened cloth then dry thoroughly. To clean the exterior use a good appliance polish wax.
  • Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.

Protect Against Freezing

Danby-DDW1802W-Built-In-Dishwasher-Fig14

If your dishwasher is left in an unheated place during the winter, ask a service technician to:

  • Cut off electrical power to the dishwasher and remove fuses or trip circuit breaker.
  • Turn off the water supply and disconnect the water inlet pipe from the water valve.
  • Drain the water from the inlet and water valve. pipe (Use a pan to catch the water.)
  • Reconnect the water inlet to the water valve. pipe
  • Remove the plastic sump cover in the tub the bottom and use a sponge to soak up the water in rubber boot.

Cleaning the Spray Arms

It is necessary to clean the spray arms regularly as hard water chemicals will clog the spray arm jets and bearings. To remove the spray arm, screw off the nut to take out the washer on top of the spray arm and remove the arm. Wash the arms in soapy, warm water and use a soft brush to clean the jets. Replace after rinsing them thoroughly.

Cleaning the Filters

Danby-DDW1802W-Built-In-Dishwasher-Fig14

Filter assembly

  • For best performance and results, the filter assembly must be cleaned.
  • The filter efficiently removes food particles from the wash water, allowing it to be recirculated during the cycle. For this reason, it is a good idea to remove the larger food particles trapped in the filter after each wash cycle by rinsing the semicircular filter and cup under running water.
  • To remove the filter assembly, pull on the cup handle in the upward direction. The entire filter assembly should be cleaned at least once a month.
  • To clean the coarse filter and the fine filter, use a cleaning brush. Then, reassemble the filter parts as shown in the figure at left and reinsert the entire assembly in the dishwasher, positioning in its seat and pressing downward.
  • The dishwasher must never be used without the filters. Improper replacement of the filter may reduce the performance level of the appliance and may damage dishes and utensils.

WARNING!

Never run the dishwasher without the filters in place.

Cleaning the Door

  • To clean the edge around the door, you should use only a soft warm, damp rag. To prevent penetration of water into the door lock and electrical components, do not use a spray cleaner of any kind.
  • Also, never use abrasive cleaners or scouring pads on the outer surfaces because they will scratch the finish. Some papers towels can also scratch or leave marks on the surface.

Cleaning the Drain Pump

Danby-DDW1802W-Built-In-Dishwasher-Fig14

Something will occasionally move into the filters and the drain pump. If this occurs, the drain pumps employed in our dishwashers are designed to automatically reverse, ejecting the item back into the sump area or down the drain. If you have to remove an obstacle from the drain pump, before you remove the filters, you should turn off the power; Then remove the small black insert from the sump area. (You might want to remove any standing water first). Scoop out the item that is probably in the sump area and causing the obstruction. Remember to replace the black insert before replacing the filters.

How to Keep Your Dishwasher Running Properly

  • After Every Wash
    After every wash, turn off the water supply to the appliance and leave the door slightly ajar so that moisture and odors are not trapped inside.
  • No Solvents or Abrasive Cleaning Products
    To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products. Use only a
  • When You Go on Holiday
    When you go on holiday, it is recommended that you run a wash cycle with the dishwasher empty and then remove the plug from the socket, turn off the water supply and leave the door of the appliance slightly ajar. This will help the seals last longer and prevent odors from forming in the appliance.
  • Seals
    One of the factors that cause odors to form in the dishwasher is food that remains trapped in the seals. Periodic cleaning with a damp sponge will prevent this from occurring. cloth and warm, soapy water. To remove spots or stains from the surface of the interior, use a cloth dampened with warm water and a little white vinegar, or a cleaning product made specifically for dishwashers.

BEFORE CALLING FOR SERVICE

Troubleshooting Tips

Review the chart on the following pages before calling for service.

Problem

Dishwasher doesn’t run
Drain pump doesn’t Overflow stop
Noise
Possible Causes What To Do
Fuse blown, or the
Replace fuse or reset circuit breaker. Remove any other circuit breaker acted appliances sharing the same circuit with the dishwasher
Power supply is not turned on
Make sure the dishwasher is turned on and the door is closed securely.
Make sure the power cord is properly plugged into the wall socket.
Water pressure is low
Check that the water supply is connected properly and the water is turned on.
The system is designed to detect an overflow. When it does, it shuts off the circulation pump and turns on the drain pump.
Some audible sounds are Sound from soft food shredding action and detergent cup normal opening.
Utensils are not secure in the baskets or something small has dropped into the basket
Ensure everything is secured in the dishwasher.
Motor hums
Suds in the tub
Improper detergent
Spilled rinse agent
Dishwasher has not been used regularly. If you do not use it often, remember to set it to fill and pump out every week, which will help keep the seal moist.
Use only the special dishwasher detergent to avoid suds.
If this occurs, open the dishwasher and let the suds evaporate.
Add I gallon of cold water to the tub. Close and latch the dishwasher, then drain out the water by slowly turning the dial until a drain period is reached. Repeat if necessary.
Always wipe rinse agent spills immediately.
Stained tub interior
Dishes are not dry
Detergent with coloring was used
Rinse agent dispenser is empty
Make sure that the detergent used is without coloring.
Make sure that the rinse agent dispenser is filled.

Spots and filming on glasses and flatware
Extremely hard water
Low inlet temperature
Overloading the dishwasher
Improper loading
Old or damp powder detergent
Empty rinse agent dispenser
Incorrect dosage of detergent
To remove spots from glassware:
Remove all metal utensils from the dishwasher.
Do not add detergent.
Choose the longest cycle.
Start the dishwasher and allow it to run for about
18 to 22 minutes, then it will be in the main wash.
Open the door to pour 2 cups of white vinegar into the bottom of the dishwasher.
Close the door and let the dishwasher complete the cycle. If the vinegar does not work: Repeat as above, except use 1/4 cup (60 ml)of citric acid crystals instead of vinegar.

Glassware is cloudy
Combination of soft Use less detergent if you have soft water and select a water and too much shortest cycle to wash the glassware and to get them clean. detergent
Yellow or brown film Tea or coffee stains on inside surfaces
Using a solution of 1/2 cup of bleach and 3 cups warm water to remove the stains by hand.
A WARNING
You have to wait for 20 minutes after a cycle to let the heating elements cool down before cleaning the interior; otherwise, burns will happen.
Iron deposits in water can cause an overall film
Call a water softener company for a special filter.
White film on inside Hard water minerals surface
To clean the interior, use a damp sponge with dishwasher detergent and wear rubber gloves. Never use any other cleaner than dishwasher detergent for the risk of foaming or suds.
Dishes block detergent Re-loading the dishes properly.
Detergent left in dispenser cups
Steam
cups
Normal phenomenon
Black or gray marks on dishes
There is some steam coming through the vent by the door latch during drying and water draining.
Aluminum utensils have Use a mild abrasive cleaner to eliminate marks. rubbed against dishes
Water standing in the bottom of the tub
This is normal
Water doesn’t pump
Drain is clogged out of the tub
Dishwasher leaks
A small amount of clean water around the outlet on the tub bottom at the back of the tub keeps the water seal lubricated.
Make sure the kitchen sink is draining well.
If the dishwasher drains into a disposer, run it clear.
Overfill dispenser or rinse Be careful not to overfill the rinse aid dispenser. aid spills
Spilled rinse aid could cause oversudsing and lead to overflowing. Wipe away any spills with a damp cloth.
Dishwasher isri t level Make sure the dishwasher is level.

REFRENCE LINK

Leave a Reply