Yealink DD10K DECT USB Dongle for Bluetooth Headsets Guide
Introduction
DECT USB dongle DD10K allows you to turn the SIP-T41S/ T42S/T54W IP phone to the DECT desk phone (hereinafter referred to as DD phone). After that, you can use the IP phone as a handset with a base station. DECT USB dongle DD10K also allows you to turn the SIP-T58V/ T58A/T58W/T56A/T53/T53W/T54W/T57W/VP59 IP phone to the corded-cordless phone. After that, you can use the IP phone as a base station and its handset 1. The features introduced in this guide apply to the following Yealink IP phones:
- SIP-T41S/T42S IP phones running firmware V82 or later.
- SIP-T58V/T58A/T58W/T56A IP phones running firmware V83 or later.
- SIP-T53/T53W/T54W/T57W/VP59 IP phones running firmware V85 or later.
Frequency bands: 1880-1900 MHz (Europe), 1920-1930 MHz (US)
DD10K Package Content
Assembling the DD10K
To assemble the DD10K: Insert the DD10K into the USB port on the back of the phone. If the firmware versions of the DD10K and IP phone do not match, the IP phone will upgrade/downgrade the DD10K.
Getting Started (for T58V/T58A/T58W/T56A/T53/ T53W/T54W/T57W/VP59)
Handset Registration Mode
Before registering the handset, make sure the IP phone is in registration mode.
To set the IP phone to the handset registration mode:
- Insert the DD10K.
- Swipe left or right to go to the second idle screen.
- Navigate to DECT Settings->Handsets.
- Tap Register (press Start Reg for T53/T53W/T54W).
Handset Registration
You can register up to other four handsets on one phone. The supported handsets include W52H, W53H, W56H, W57R, W59R, W73H, W78H and DD phone.
- Assemble the DD10K.
- Press the Menu soft key when the phone is idle, and then select Status->Phone Mode.
- Select the desired mode and click OK. The phone will reboot to make the change take effect.
Registration
You can register the DD phones to W70B/W80 Multi-Cell System/W90 Multi-Cell System. Each DD phone can be registered to only one base station. Before registering the DD phone, make sure the base station is in registration mode (long press on the base station till the registration LED flashes).
Basic Call Features (for T41S/T42S/T54W)
Call Mute and Un-mute
- Press to mute the microphone during a call.
- Press again to unmute the call.
To resume the call, do one of the following:
- If there is only one call on hold, press the Resume soft key.
- If there is more than one call on hold, press
select the desired call, and then press the Resume soft key.
Blind Transfer
- Press the Transfer soft key during an active call. The call is placed on hold.
- Enter the number you want to transfer to.
- Press the Transfer soft key.
Semi-Attended Transfer
- Press the Transfer soft key during an active call. The call is placed on hold.
- Enter the number you want to transfer to, and then press
.
- Press the Transfer soft key when you hear the ring-back tone.
Attended Transfer
- Press the Transfer soft key during an active call. The call is placed on hold.
- Enter the number you want to transfer to, and then press
.
- Press the Transfer soft key when you hear the ring-back tone.
Call Forward
To enable call forward:
- Press the Menu soft key when the phone is idle, and then select Features->Call Forward.
- Select a desired account.
- Select the desired forward type: Always Forward—-Incoming calls are forwarded unconditionally. Busy Forward—-Incoming calls are forwarded when the phone is busy. No Answer Forward—-Incoming calls are forwarded if not answered after a period of time.
- Enter the number you want to forward to. For No Answer Forward, press
select the desired ring time to wait before forwarding from the After Ring Time field.
- Press the Save soft key to accept the change.
Conference
- Press the Conf soft key during an active call. The call is placed on hold.
- Enter the number of the second party, and then press the Send soft key.
- Press the Conf soft key again when the second party answers. All parties are now joined in the conference.
- Press the End Call soft key to disconnect all parties.
Speed Dial
To configure a speed dial key:
- Press the Menu soft key when the phone is idle, and then select Features->DSS Keys.
- Select the desired DSS key, and then press the Enter soft key.
- Select SpeedDial from the Type field, select the desired line from the Account ID field, enter a label in the Label field, and then enter the number in the Value field.
- Press the Save soft key to accept the change. To use the speed dial key: Press the speed dial key to dial out the preset number.
Customizing Your Phone (for T41S/T42S/T54W)
Handset Name
To rename the handset:
- Press the Menu soft key when the phone is idle, and then select Settings->Basic Settings->Phone Name.
- Edit the value in the Phone Name field.
- Press the Save soft key to accept the change.
Call History
- Press the History soft key when the phone is idle, press
to scroll through the list.
- Select an entry from the list, you can do the following:
- Press the Send soft key to call the entry.
- Press the Delete soft key to delete the entry from the list.
- Press the Option soft key, and do the following:
- Select Detail to view detailed information about the entry.
- Select Add to Contact to add the entry to the local directory.
- Select Add to Blacklist to add the entry to the blacklist.
- Select Delete All to delete all entries from the list.
Contact Directory
To add a contact:
- Press the Directory soft key when the phone is idle.
- Press the Add soft key to add a contact.
- Enter a unique contact name and contact numbers in the
- corresponding fields.
- Press the Add soft key to accept the change.
To edit a contact:
- Press the Directory soft key when the phone is idle.
- Press
select the desired contact, press the Option soft key, and then select Detail from the prompt list.
- Edit the contact information.
- Press the Save soft key to accept the change.
To delete a contact:
- Press the Directory soft key when the phone is idle, and then select All Contacts.
- Press
select the desired contact, press the Option soft key, and then select Delete from the prompt list.
- Edit the contact information.
- Press the OK soft key when the phone prompts “Delete selected item?
Volume Adjustment
- Press
during a call to adjust the receiver volume of the handset/speakerphone/headset.
- Press
when the phone is idle or ringing to adjust the ringer volume.
Ring Tones
- Press the Menu soft key when the phone is idle, and then select Settings->Basic Settings->Sound->Ring Tones.
- Press
select Common or the desired account, and then press the Enter soft key.
- Press
select the desired ringtone.
- Press the Save soft key to accept the change.
Warranty
Our product warranty is limited only to the unit itself, when used normally in accordance with the operating instructions and the system environment. We are not liable for damage or loss resulting from the use of this product, or for any claim from a third party. We are not liable for problems with the Yealink device arising from the use of this product; we are not liable for financial damages, lost profits, claims from third parties, etc., arising from the use of this product.
Regulatory Notices
Operating Ambient Temperatures
- Operating temperature: +32 to 104°F (0 to 40°C)
- Relative humidity: 5% to 90%, non-condensing
- Storage temperature: -22 to +158°F (-30 to +70°C)
Safety Instructions
Save these instructions. Read these safety instructions before use! The following basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and other personal injury.
General Requirements
- Before you install and use the device, read the safety instructions carefully and observe the situation during the operation.
- During the process of storage, transportation, and operation, please always keep the device dry and clean.
- During the process of storage, transportation, and operation, please avoid collision and crash of the device.
- Please attempt not to dismantle the device by yourself. In case of any discrepancy, please contact the appointed maintenance center for repair.
- Without prior written consent, no organization or individual is permitted to make any change to the structure or the safety design of the device. Yealink is under no circumstance liable to consequences or legal issues caused by such changes.
- Please refer to the relevant laws and statutes while using the device. The legal rights of others should be respected as well.
Environmental Requirements
- Place the device in a well-ventilated place. Do not expose the device to direct sunlight.
- Keep the device dry and free of specks of dust.
- Place the device on a stable and level platform.
- Please place no heavy objects on the device in case of damage deformation caused by the heavy load.
- Keep at least 10 cm between the device and the closest object for heat dissipation.
- Do not place the device on or near any inflammable or fire-vulnerable object, such as rubber-made materials.
- Keep the device away from any heat source or bare fire, such as a candle or an electric heater.
Operating Requirements
- Do not let a child operate the device without guidance.
- Do not let a child play with the device or any accessory in case of accidental swallowing.
- Please use the accessories provided or authorized by the manufacturer only.
- The power supply of the device shall meet the requirements of the input voltage of the device. Please use the provided surge protection power socket only.
- Before plugging or unplugging any cable, make sure that your hands are completely dry.
- Do not spill liquid of any kind on the product or use the equipment near water, for example, near a bathtub, washbowl, kitchen sink, wet basement, or swimming pool.
- Do not tread on, pull, or over-bend any cable in case of malfunction of the device.
- During a thunderstorm, stop using the device and disconnect it from the power supply. Unplug the power plug and the Asymmetric Digital Subscriber Line (ADSL) twisted pair (the radio frequency cable) to avoid a lightning strike.
- If the device is left unused for a rather long time, disconnect it from the power supply and unplug the power plug.
- When there is smoke emitted from the device, or some abnormal noise or smell, disconnect the device from the power supply, and unplug the power plug immediately. Contact the specified maintenance center for repair.
- Do not insert any object into equipment slots that is not part of the product or auxiliary product.
- Before connecting a cable, connect the grounding cable of the device first. Do not disconnect the grounding cable until you disconnect all other cables.
Cleaning Requirements
- Before cleaning the device, stop using it and disconnect it from the power supply.
- Use a piece of soft, dry, and anti-static cloth to clean the device.
- Keep the power plug clean and dry. Using a dirty or wet power plug may lead to electric shock or other perils.
Always adhere to prevailing regulations
Those who fail to do so may be fined or prosecuted in accordance with the law. The crossed-out garbage can that appears on the device means that when it has reached the end of its useful life, it should be taken to a special waste disposal center and treated separately from general urban waste.
Troubleshooting
The unit cannot supply power to the Yealink device. There is a bad connection with the plug. 1. Clean the plug with a dry cloth. 2. Connect it to another wall outlet. The usage environment is out of the operating temperature range. 1. Use in the operating temperature range. The cable between the unit and the Yealink device is connected incorrectly. 1. Connect the cable correctly. You cannot connect the cable properly. 1. You may have connected a wrong Yealink device. 2. Use the correct power supply. Some dust, etc., may be in the port. 1. Clean the port. Contact your dealer or authorized service facility for any further questions.
Contact Information
YEALINK NETWORK TECHNOLOGY CO., LTD. 309, 3rd Floor, No.16, Yun Ding North Road, Huli District, Xiamen City, Fujian, P.R.C YEALINK (EUROPE) NETWORK TECHNOLOGY B.V. Strawinskylaan 3127, Atrium Building, 8th floor, 1077ZX Amsterdam, The Netherlands YEALINK (USA) NETWORK TECHNOLOGY CO., LTD. 999 Peachtree Street Suite 2300, Fulton, Atlanta, GA, 30309, USA Made in China.
Technical Support
Visit Yealink WIKI (http://support.yealink.com/) for firmware downloads, product documents, FAQs, and more. For better service, we sincerely recommend you use the Yealink Ticketing system (https://ticket.yealink. com) to submit all your technical issues.
About Yealink
Yealink (Stock Code: 300628) is a global brand that specializes in video conferencing, voice communications, and collaboration solutions with best-in-class quality, innovative technology, and user-friendly experience. As one of the best providers in more than 140 countries and regions, Yealink ranks No.1 in the global market share of SIP phone shipments (Global IP Desktop Phone Growth Excellence Leadership Award Report, Frost & Sullivan, 2019)
REFERENCE LINK