Honey Well Double Blade Stand Fan Manual

Honey Well Double Blade Stand Fan Manual

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS FAN
When using electrical appliances,basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

FOR US MODELS ONLY – This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement
fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.

1.  Use this fan only as described in this manual. Other use not recommended as it may cause fire, electric shock or injury to persons.
2.  This product is intended for household use ONLY and not for commercial,industrial or outdoor use.
3. To protect against electric shock, do not place fan in window, immerse unit, plug or cord in water or spray with liquids.
4.  This appliance has a polarized plug (one blade is wider than the other).To reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature.
5. Close supervision is necessary when any appliance is used by or near children.

FUSED SAFETY PLUG

This fan features a fused safety plug which is designed to cut off electric current to the fan if an electrical fault
occurs. Please see below for more information on how to properly use your fan and replace the safety plug fuse,
if needed

USER SERVICING INSTRUCTIONS

• If your fan loses power and you suspect that the fuse on your fan has blown, grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
•  Slide fuse cover, located on the top of the plug towards the prongs of the plug.
• Carefully remove the blown fuse and snap a new fuse into place. To Reduce the Risk of Fire, replace fuse only with 2.5 Amp, 125 volt fuse. Fully close the fuse door by sliding back into place. (Fig. 2) Discard the blown fuse. The plug should now be ready for normal use.
• To Reduce the Risk of Fire, do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.
•  If you need further information on how or when to replace the fuse in the safety plug, please contact Kaz Consumer Relations Department by visiting our website at www.honeywellpluggedin.com/fans or calling 1-800-477-0457.

BASE ASSEMBLY

1. Align the pole in the base using tabs as a guide.
2. Gently place base on its side. (Fig. 3)
3. Insert and tighten the L shaped bolt and washer on the bottom of the fan base. (Fig. 4)
4.  Tighten by turning clockwise.

PART GUIDE

1. Front Grille
2. Locking Clips
3.  Blade Nut
4.  Small Blade
5.  Large Blade
6.  Plastic Nut
7. Rear Grille
8.  Fan Head Assembly
9.  Control Panel
10.  Washer
11.  “L” Screw
12.  Motor Shaft
13.  Alignment Prongs
14.  Locking Screw
15. Extension Pole
16.  Pole Locking Nut
17. Lower Pole
18.  Base
19.  Remote Control

BLADE AND GRILLES ASSEMBLY

The small blade is packaged separately in between cardboard apart from the large blade DO NOT THROW OUT!

1.  Unscrew the blade nut clockwise and the plastic nut counterclockwise and set aside. (Fig. 5)
2.  Position the rear grille onto the fan head assembly making sure the two alignment holes are aligned with the two prongs.
3. Screw on plastic nut tightly clockwise to attach rear grille. (Fig. 6)
4.  Install the blade onto the shaft until the retaining pin fits into the notch on the blade. Now place the small blade on to the shaft making sure the alignment pin is inserted into one of the three holes on the large blade.
5.  Screw blade nut to the motor shaft counterclockwise (tighten by turning to the left).(Fig. 7)
6.  Mount the front grille and secure using the locking clips.

OPERATION

Tilt Control
The airflow can be adjusted upward or downward by tilting the fan head as desired. To change the tilting angle
of the fan head assembly, simply move the fan head to the desired angle. (Fig. 8)
Height Adjustment
Turn the pole locking nut counterclockwise to loosen the pole. Adjust the pole to the desired height and firmly
tighten the locking nut in a clockwise direction. (Fig. 9)

CONTROL PANEL OPERATION

On/Off
To turn fan on, press the Power button located at the top of the control panel. (Fig. 10)
Speed Control
To adjust the speed up or down, press the Fan Speed button repeatedly to increase level of air speed.1 (Low) 2 (Med.) 3 (High) and Off

Timer

Choose from 1, 2, 4, or 8 hour settings by performing the following function (Fig. 10):

• 1 hour: Press the Timer button once.
• 2 hours: Press the Timer button twice.
• 4 hours: Press the Timer button a third time.
•  8 hours: Press the Timer button a fourth time.

REMOTE CONTROL OPERATION

Remote Control Battery Installation Replacement Instructions

• A. Remove battery door by sliding downward in direction of arrow.
• B. Insert 2 AAA batteries into the remote following the directional guides in the recessed slots.
  Batteries are not included.
• C. Replace battery door by sliding upward opposite of arrow direction until door snaps in place.

NOTE: DO NOT MIX OLD AND NEW BATTERIES.DO NOT MIX ALKALINE, STANDARD (CARBON-ZINC)
OR RECHARGEABLE (NICKEL-CADMIUM) BATTERIES. SEE RECYCLERS IN YOUR AREA FOR PROPER
DISPOSAL OF BATTERIES.

USER SERVICING INSTRUCTIONS

Cleaning and Storage

•  Be sure your fan is in the OFF position.
•  Unplug the fan before cleaning.
•  Use only a soft, damp cloth to gently wipe the fan clean.
•  DO NOT immerse the fan in water and never allow water to enter the Motor Housing.
•  DO NOT use gasoline, paint thinner or other chemicals to clean the fan.

Removal of the Front Grille for Cleaning

• Remove the Front Grille by releasing the Grille clips.
• Unscrew the Blade Knob by turning it CLOCKWISE (REVERSE THREAD).
•  Pull the Fan Blade away from the Motor Housing.
•  Gently wipe the Fan Blade and Grilles with a soft, damp cloth.
• Assemble the fan by following the last three steps in the ASSEMBLY INSTRUCTIONS.

Storage

• For storage disassemble and clean the fan carefully as instructed. Store the fan in its original box. You may
  also leave the fan fully assembled and covered with plastic to protect it from dust. Store your fan in clean,
  dry place.

CONSUMER RELATIONS

Questions or Comments Call us toll-free at: 1-800-477-0457 E-mail: consumerrelations@kaz.com Or visit our website at: www.HoneywellPluggedIn.com/fans Please be sure to specify model number.

DOWNLOAD LINK

Honey Well Double Blade Stand Fan Manual

https://www.walmart.com/ip/Honeywell-Double-Blade-Pedestal-Electric-Stand-Fan-HSF1640B