Dreo Inverter Window Air Conditioner User Manual

Dreo Inverter Window Air Conditioner

IMPORTANT SAFETY INSTRUCTIONS

Read All Instructions and Cautionary Markings Before Operation and Installation to prevent death or injury to the user or other people and property damage, the following instructions must be followed. Incorrect operation due to ignoring of instructions may cause death, harm, or damage.

WARNING

• Installation must be performed according to the installation instructions. Improper installation can cause water leakage, electrical shock, or fire.
• Use only the included accessories and parts, and specified tools for the installation. Using nonstandard parts can cause water leakage, electrical shock, fire, and injury or property damage.
• Install the appliance on a flat, sturdy surface. Failure to do so could result in damage or excessive noise and vibration.
• The appliance must be kept free from obstruction to ensure proper function and mitigate safety hazards.
• Do not modify the length of the power cord or use an extension cord to power the appliance.
• Do not share a single outlet with other electrical appliances. The improper power supply can cause fire or electrical shock.
• Do not install your air conditioner in a wet room such as a bathroom or laundry room. Too much exposure to water can cause electrical components to short circuit.
• Do not install the appliance in a location that may be exposed to combustible gas, as this could cause a fire.
• The appliance has wheels to facilitate moving. Make sure not to use the wheels on thick carpets or to roll over objects, as these could cause tipping.
• Do not operate the appliance if it has been dropped or damaged.

CAUTION

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
• Prior to cleaning or other maintenance, the appliance must be disconnected from the supply mains.
• Never use this appliance if it is not working properly, or if it has been dropped or damaged.
• Do not run the cord under the carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not route the cord under furniture or appliances. Arrange the cord away from the traffic area and where it will not be tripped over.
• Do not operate with a damaged cord, plug, power fuse, or circuit breaker. Discard the appliance or return it to an authorized service facility for examination and/or repair.
• To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
• The appliance shall be installed in accordance with national wiring regulations.
• Contact the authorized service technician for repair or maintenance of this appliance.
• Contact the authorized installer for the installation of this appliance.
• Do not cover or obstruct the inlet or outlet grilles
• Do not use this product for functions other than those described in this instruction manual.
• Before cleaning, turn off the power and unplug the appliance.
• Disconnect the power if strange sounds, smell, or smoke comes from it.
• Hold the plug by the head of the power plug when taking it out.
• Turn off the product when not in use.

Operation of Current Device

The power supply cord contains a current measuring device that detects damage to the power cord. Test your power supply cord as follows:

1. Plug in the air conditioner.
2. The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will notice a click as the RESET button pops out.
3. Press the RESET Button. You will notice a click as the button engages. 4. The power supply cord is now supplying electricity to the unit. (On some products this is also indicated by a light on the plug head.)
   

NOTE

•  The power supply cord with this air conditioner contains a current detection device designed to reduce the risk of fire.
• In the event that the power supply cord is damaged, it can not be repaired. It must be replaced with a cord from the manufacturer.
• Do not use this device to turn the unit on or off.
• Always make sure the RESET button is pushed in for a correct operation.
• The power supply cord must be replaced if it fails to reset when either the TEST button is pushed, or it can not be reset. Please contact Customer Service.

Window Requirements

1. This air conditioner is designed to be installed in a standard single-hung or double-hung window with a window width between 25″ and 36″ (645mm – 915mm).
2. The air conditioner can be installed without the side panels to fit in a narrow window opening. See the window dimensions. If the air conditioner is installed on a window with a width of 645-720mm, the air conditioner must be installed to the right and the right bracket must be about the air conditioner, otherwise, the air conditioner will not operate normally.
3. The lower sash (the lower part of the window that moves up and down) must allow for 14.5″ of vertical clearance when open.
4. All supporting parts must be secured to firm wood, masonry, or metal. 5. The electrical outlet must be within reach of the power cord.

NOTE

• Save the product packaging and installation instructions for future reference.
• Store the air conditioner in the product box during winter or when not in use.

If AC Is Blocked By Storm Window

• Add wood as shown, or remove the storm window before the air conditioner is installed.
• If Storm Window Frame must remain, be sure the drain holes or slots are not caulked or painted shut. Accumulated Rain Water or Condensate must be allowed to drain out.

Please note that:

1. The installation site should be in a well-ventilated condition.
2. The sites for installing and maintaining an air conditioner using Refrigerant R32 should be free from open fire or welding, smoking, drying oven, or any other heat source higher than 548℃ which easily produces open fire.
3. When installing an air conditioner, it is necessary to take appropriate anti-static measures such as wearing anti-static clothing and/or gloves.
4. It is necessary to choose a site convenient for installation or maintenance wherein the air inlets and outlets of the indoor and outdoor units should be not surrounded by obstacles or close to any heat source or combustible and/or explosive environment.
5. If the indoor unit suffers a refrigerant leak during the installation, all the personnel should go out till the refrigerant leaks completely for 15 minutes. If the product is damaged, it is a must to carry such damaged product back to the maintenance station and it is prohibited to weld the refrigerant pipe or conduct other operations on the user’s site.
6. It is necessary to choose the place where the inlet and outlet air of the indoor unit is even.
7. It is necessary to avoid places where there are other electrical products, power switch plugs, sockets, kitchen cabinets, beds, sofas, and other valuables right under the lines on two sides of the indoor unit, and also prevent mechanical damage from occurring.

Reference Link

https://www.dreo.com/collections/air-conditioners

PDF Link

https://www.dreo.com/support/product/dreo-arctic-one-inverter-window-air-conditioner

Buy Related Product on Amazon

Buy on Amazon