Escort SMART MIRROR User Manual
Introduction
The ESCORT SmartMirror is intended to assist you in safe driving by providing directions, hands-free phone connectivity, and a broader view during reversing. The driver is solely responsible for safe vehicle operation and passenger safety according to the laws of the country and local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of your vehicle. ESCORT cannot accept any responsibility for accidents resulting from failure to observe these precautions.
- Any unauthorized modifications or damage to the products may result in electrical shock. Handle all components with care. Inspect regularly for damage to components and cabling.
- Installer is responsible for ensuring that the installation of this product does not void or affect the vehicle manufacturer’s warranty. ESCORT is not liable in any part for improper installation resulting in loss or damage to your property, or for voiding all or part of the vehicle manufacturer’s warranty.
- Do not apply excessive force to any of the components contained within this kit. Excessive force used before, during, or after installation that results in a damaged or non-functional product shall void all warranties.
- Please follow all procedures contained within this installation manual. Improper installation or modification of this product shall void all warranties.
Parts Included:
- SmartMirror
- Wire harness
- Universal mount & screws
- Universal button
- Allen key
- External GPS antenna (not used with all installations)
Tools Recommended for Proper Installation:
- Safety Glasses
- DC voltmeter or test light
- Crimping pliers
- Wire strippers
Preparation
- Inspect the mirror for damage
- Check the parts list for accuracy.
NOTE: ESCORT does not recommend installing this mirror if your vehicle has airbag sensors in the headliner area or if your vehicle is equipped with OnStar.
If your car, truck, or SUV mirror is mounted within the windshield, not stuck on like the wedge mount or Camlock style, detachment is not recommended. If your windshield wipers have a sensor mounted to your rearview mirror, installation of this mirror will inactivate that function.
The ESCORT SmartMirror is packaged with a “universal” wedge-style mount for attaching to the windshield. Camlock and other mounting adapters are sold separately. For a complete list of available mounting hardware, visit www.EscortSmartMirror.com.
The two most common mirror mounting styles are:
Wedge Mount
Generally standard on vehicles manufactured in the United States, regardless of vehicle make. This style of mirror can be found with or without a screw. See page 5 for removal instructions.
Camlock Mount
Generally standard on vehicles manufactured outside of the United States. This style of mirror must be removed by turning the mirror 90 degrees so that it is perpendicular to the dash and pulling down on the mirror.
Factory Mirror Removal
Screw Wedge Mount
Using a screwdriver or torx bit, loosen the screw in the base of the mirror. After loosening the screw, gently lift upward to slide the mirror off of the mirror mount.
Screwless Wedge Mount
Using a small 1/8″ (4 mm) flat-blade screwdriver, insert the flat end into the opening at the bottom of the mirror mount at the windshield. Slide the screwdriver into the center of the mirror mount until resistance is felt. Gently apply a small amount of additional upward force to lift away the locking spring in the mount. While still applying upward pressure with the screwdriver, grasp the mirror bracket and wiggle side to side. Lift the mirror up toward the headliner and off the windshield mount button.
Camlock Mount
Grasp the base of the mirror. Rotate 90 degrees left or right. Slide the mirror downward toward the dash to remove it.
- Install universal windshield mount to SmartMirror using supplied screws. There are multiple holes to allow proper mirror placement. Do not over-tighten screws.
- Mount SmartMirror to the windshield by sliding the universal mount over the factory button on the windshield. Tighten the screw using supplied Allen key.
- Find a suitable mounting location for the microphone. For best results place the microphone within two (2) feet of the driver’s head. The top of the A-pillar or above the mirror in the center of the windshield are recommended locations. Route wire to mirror and plug into 1/8″ jack.
- Plug in the supplied power harness and route to a suitable location to make power connections. Connect wires to the car as follows:
- Yellow 12-Volt Constant
- Red 12-Volt Switched (Ignition)
- Black Chassis Ground
- Green Reverse Light
- Video 1 RCA Additional Camera
- Video 2 RCA Reverse Camera Input
Specifications
- CPU Samsung S3C2440A-400MHZ
- RAM 64MB
- Memory Card 2GB
- LCD 4-inch / 480×272 pixel
- Touch Screen Four-line resistive touch
- Speakers Internal 8Ω/1W
- GPS Switzerland-UBLOX-LEA4S
- Bluetooth Version 1.2
- Power Supply 12VDC
- Power Consumption <10W
- Current Draw <500 mA
- Video Format PAL/NTSC
- Video Input 1Vp-p@ 75 Impedance
- Operating Temperature 0° C – 60° C
- Storage Temperature -20° C – 60° C
Maintenance
The ESCORT SmartMirror requires little care, however, to maintain it in optimum condition, follow the procedures below:
- Keep SmartMirror away from excessive moisture, extreme heat, or cold and magnetic fields.
- Keep liquids away from the display.
- Do not place external devices or other objects on the top of SmartMirror.
- Occasionally clean mirror glass with a soft cloth moistened with water or window cleaner.
2009 ESCORT Inc. Escort is a registered trademark of Escort Inc. Features, specifications, and prices are subject to change without notice.
