Schlage FE575 Keypad Lever and Elan Lever User Manual

Schlage FE575 Keypad Lever and Elan Lever User Manual

Warranty

Lifetime Limited Mechanical and Finish Warranty and 3-Year Limited Electronics Warranty Subject to the terms and conditions of the warranty, Schlage extends a lifetime limited mechanical and finish warranty and a three-year limited electronics warranty to the original consumer user (“Original User”) of our Schlage brand product (“Product”) against defects in material and workmanship, as long as the Original

The user occupies the residential premises upon which the Product was originally installed. See answers.schlage.com for specific warranty details and limitations, or contact Schlage Customer Service at (888) 805-9837 in the U.S., 800-997-4734 in Canada, or 018005067866 in Mexico for assistance.

Register your Product
PLEASE KEEP THIS GUIDE
This guide contains important information about your lock!

• Default User Codes and Programming Codes are located on the sticker on the back of this guide! You will need these if you ever need to reset your lock back to factory default settings!
• The sticker also contains your serial number, which may be needed for warranty and customer service support.
• Instructions for adding and deleting User Codes, changing the lock behavior, troubleshooting, customer service, and more are explained in this guide!

WHY DO I NEED KEYS IF THIS IS A KEYLESS LOCK?
Good question! If the battery is dead, or no User Code is known, you can use the key to gain access by employing the emergency key override.

Lock parts Model BE365

Keypad

• Used to enter codes for programming and unlocking. See Programming Guide on page 9 and Locking and Unlocking on page 7 for more information.

Outside Thumbturn

• Used to unlock the lock after a valid User Code has been entered, or to lock the lock after the Schlage button has been pressed.

Inside thumb turn

• Used to lock or unlock the lock.

Keypad Lever

Models FE575 (Auto Lock) and FE595 (Flex Lock)

Keypad

• Located on the outside of the lock.
• Used to enter codes for programming and unlocking. See Programming Guide on page 9 and Locking and Unlocking on page 7 for more information.

Lever

• The inside lever can be rotated at any time to retract the latch.
• The outside lever can be rotated at any time, but will only retract the latch when the lock is unlocked.

Cylinder

• Located on the outside of the lock.
• Used only in emergencies to unlock the lock. See Key Override on page <?>.

Thumbturn

• FE595 ONLY: Used to put the lock in a locked or unlocked state.

LITHIUM BATTERIES?
Lithium batteries may have a longer life, but when they begin to fail, they fail quickly. We don’t recommend them because they don’t give you a lot of time to change your batteries before the lock is completely dead.

Locking and unlocking

From the outside:
To Lock

1. Press the Schlage button.
2. Rotate the thumb-turn away from the hinges.

To Unlock
If lighting is low, press the Schlage button to illuminate the keypad before beginning

1. Enter a User Code into the keypad.
2. Rotate the thumb-turn toward the hinges.

If the Turn Lock feature is disabled, a valid User Code must be entered to lock the door.

Changing the battery 
Replace the batteries in your lock at the same time each year that you test and replace the batteries in your smoke alarms. This will ensure continued reliable operation. Use a high-quality alkaline 9-volt battery for replacement.

1. Remove the inside cover.
2. Replace the battery.
3. Re-tuck wires so they will not be crimped. Replace the cover.

Key Override

Key Override can be used to gain access when the battery is completely dead and no valid User Code is known.

1. Insert the key into the cylinder.
2. Rotate the key 90° toward the hinges.
3. Push the key and cylinder into the thumb turn.
4. Rotate the thumb and turn 90° toward the hinges.†

Reverse steps to relock. Hold the thumb turn still while removing the key.

Models FE575— Auto Lock and FE595— Flex Lock

Key Override
Key Override can be used when the battery is completely dead, or when no valid User Code is known.

1. Insert key.
2. Rotate the key 270° to unlock.
3. Rotate the knob/lever to open the door.

Rotate the key back to the starting position to relock. The key cannot be removed from the cylinder while the lock is unlocked.

Changing the Battery 
Replace the batteries in your lock at the same time each year that you test and replace the batteries in your smoke alarms. This will ensure continued reliable operation. Use a high-quality alkaline 9-volt battery for replacement.

FE595

1. Remove the inside cover.
2. Replace the battery.
3. Replace the cover

Keypad Locks

LITHIUM BATTERIES?
Lithium batteries may have a longer life, but when they begin to fail, they fail quickly. We don’t recommend them because they don’t give you a lot of time to change your batteries before the lock is completely dead.

FE575

1. Remove the lock from the door.
2. Open the battery compartment and replace the battery.
3. Reinstall the lock on the door.

Programming Guide

Schlage Button Signals
The color of the Schlage button indicates the status of the lock.

Orange

• the lock is in programming mode

Green

• a correct user code was entered
• the programming process is complete

Red

• an incorrect user code was entered
• there was an error in the programming
• low batteries
• red blinking indicates a critically low battery

Codes
Control of the lock is simply managed via a six-digit Programming Code and four-digit User Codes.

PROGRAMMING CODE (Six Numbers)

• The lock comes preset with one unique default Programming Code. It can be found on the stickers, one on the back of the keypad assembly and one on the front of this User Guide.
• Used to put the lock in programming mode.
• DOES NOT unlock the lock.
• The first four numbers must be different from all of the User Codes currently in the lock.
• If you forget the Programming Code, you can reset the lock to factory settings, which restores the default Programming Code.

USER CODES (Four Numbers)

• The lock comes preset with two unique default User Codes. They may be found on the stickers, one on the back of the keypad assembly, and one on the front of this User Guide.
• Used to unlock the lock.
• These four numbers must be different from the first four numbers of the Programming Code.
• Up to 19 possible User Codes can be stored in the lock at one time.

Default Code Locations

The Default User Codes and Programming Codes are located in two places:

Back of the Keypad

• You must remove the Keypad from the door to see this sticker.

Basic Controls

• Write your programming code here for easy access.
• If you make a mistake during programming, press the Schlage button repeatedly until the keypad lights blue. Then start over.

ADDING USER CODES*

These four numbers must be different from the first four numbers of the Programming Code.

DELETING USER CODES

CHANGING THE PROGRAMMING CODE* 

The first four numbers must be different from all of the User Codes currently in the lock.

Enhanced Controls

Schlage’s keypad locks were designed with added features that allow you to adapt the lock to your needs. Additional features that you can choose to use include:

ENABLE VACATION MODE

When enabled, no User Codes will unlock the door, preventing any unauthorized attempts of entry when no one is home for a prolonged period.

DISABLE VACATION MODE

ENABLE OR DISABLE BEEPER

The beeper can be turned off if desired. Beeps will still sound during programming.

• The beeper may not be audible to everyone.

DELETE ALL USER CODES

Removes ALL User Codes from the lock.

ENABLE OR DISABLE LOCK & LEAVE
KEYPAD DEADBOLT (BE365) ONLY

Enabled by default. When enabled, the deadbolt can be locked from the outside by pressing the Schlage button and rotating the thumb turn. When disabled, a User Code must be entered before rotating the thumb turn. Disabling this feature keeps an unauthorized person from locking the door from the outside

Record Your Codes

KEYPAD WEAR
Consider changing your codes periodically so buttons wear evenly.

Troubleshooting

Browse to answers.schlage.com and click on Electronic Keypad Locks in the menu on the right side for videos, troubleshooting, FAQ, and more.

Lock Issue		Beeps*	Lights	Solution
KEYPAD DEADBOLT ONLY	I can unlock my deadbolt by simply pushing the Schlage button. I don’t need a code.	1 High	Green Blinking	Your lock has been installed incorrectly and is not secure. Repeat the installation process. Ensure the cam and bolt positions are correct, as referenced in the installation instructions. Browse to answers.schlage.com and search on “Installing BE365” for a video.
	After pushing  and rotating thumbturn, the deadbolt does not extend.	None	None	The lock and Leave feature is disabled. See Enable or Disable Lock & Leave on page 11.
	After entering my User Code, the lock flashes green, but I cannot unlock the lock.	1 High	Green Blinking	The lock is malfunctioning. Call Customer Service.
	Outside thumbturn does not freely spin after deadbolt is thrown.	None	None	The lock is malfunctioning. Call Customer Service.
I forgot my Programming Code.		None	None	Check the front of this guide or the back of the keypad assembly for the default Programming Code.
				If needed, restore lock to factory settings. See  WARNING  on page 13.
I need to delete a User Code that I don’t remember.		None	None	Delete all User Codes. Then add all needed User Codes back into the lock. See Programming Guide on page 9.
User Code does not unlock lock.		2	Red	User Code entered is not a valid User Code.
		1 High, 1 Low	Green then Red	Vacation Mode is enabled. See Disable Vacation Mode on page 11.
does not light when numbers are pressed.		None	None	Too many incorrect User Codes have been entered. Wait 30 seconds and try again.
				If the keypad does not respond after 30 seconds, then replace battery. See Changing the Battery on page 7 for the Keypad Deadbolt or Changing the Battery on page 7 for Keypad Lock.
There is a delay before unlocking after a valid User Code is entered.		High/ Low, then 1	Red then Green	The battery is low and should be replaced. See Changing the Battery on page 7 for Keypad Deadbolt or Changing the Battery on page 7 for Keypad Lock.
blinking red but no codes have been entered.		None	Quick Red Blinking	The battery is dead and MUST be replaced. See Changing the Battery on page 7 for Keypad Deadbolt or Changing the Battery on page 7 for Keypad Lock.
Cannot add a new User Code.		High/ Low	Red	19 User Codes already exist. Delete a User Code before adding a new one. See Deleting User Codes on page 10.
		2	Red	The second User Code entered did not match first User Code entered. See Adding User Codes* on page 10.
				The User Code matches the first four digits of the existing Programming Code.
Cannot delete a User Code.		2	Red	The second User Code entered did not match first User Code entered.
Cannot change Programming Code.		2	Red	The second Programming Code entered did not match first Programming Code entered. See Changing the Programming Code* on page 10.
				The first four digits of the new Programming Code match an existing User Code.
Cannot delete all User Codes.		2	Red	The programming Code entered the second time is incorrect.
The lock will not stay in programming mode.		2	Red	Any key other than that was pressed immediately after programming mode was entered.
				An incorrect entry was made during the programming process.

Several beeps if the beeper is turned on.

Restore Factory Settings

If you lose or forget your Programming Code, you can restore the factory settings, which will restore the default Programming code.

1. Disconnect the battery.
2. Press and release the Schlage button.
3. The following steps must occur within 10 seconds:
   • a Reconnect the battery. The Schlage button will light green for one second.
   • b Then, press and hold the Schlage button until it lights green and the lock beeps.
4. Try entering one of the default User Codes.

WARNING
Locate the default Programming and User Codes on the front of this guide or the back of the Keypad Assembly before beginning! Default Programming and User Codes will be restored. All existing User Codes and current Programming Codes will be erased. CUSTOMER SERVICE CANNOT RETRIEVE LOST DEFAULT CODES! DO NOT RESTORE FACTORY SETTINGS UNLESS YOU CAN LOCATE THE DEFAULT CODES.

REFERENCE LINK

https://www.schlage.com

https://www.schlage.com/en/home/products/FE575PLYFFFELA.html