Baby Brezza FRP0046 Formula Pro Advanced User Manual
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should be followed, including the following:
- Read all instructions before using.
- Do not touch hot surfaces.
- To protect against electric shock and injury to persons, do not immerse cord, plug, or appliance in water or other liquid.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they are closely supervised and instructed concerning use of the appliance by a person responsible for their safety. Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance.
- Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or disassembling parts and before cleaning. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.
- Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Contact the manufacturer at their customer service telephone number for information on examination, repair, or adjustment.
- The use of accessory attachments not recommended by the appliance manufacturer may cause fire, electric shock or injury.
- Use on level surface and be sure there is no debris under the unit and the rubber wheels are touching the surface.
- Household use only. Do not use outdoors.
- Do not let cord hang over edge of table or counter, or touch hot surfaces.
- Do not place on or near hot gas or electric burner, or in a heated oven.
- Do not use appliance for other than intended use.
- Do not attempt to use the machine without water in the water tank.
- This appliance has a polarized plug (one blade wider than the other). To reduce risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not t fully into the outlet, reverse the plug. If it still does not t, contact a qualified electrician. Do not attempt to modify the plug in any way.
- A short power-supply cord is provided to reduce risks of becoming entangled in or tripping over a longer cord. Longer detachable power-supply cords or extension cords are available and may be used if care is exercised in their use. If using the machine with an extension cord, make sure the cord is the proper electrical rating for the machine. The extension cord should be arranged so that it does not drape over a counter top or tabletop, where it can be pulled on by children or tripped over unintentionally.
- Before serving make sure formula mixture is at safe temperature for baby.
- Avoid contact with moving parts. Never remove powder container, powder container lid, funnel or water tank while machine is in operation.
- Do not disassemble or open base of machine.
WARNING:
- Set-up & cleaning is critical to the function of your Formula Pro® Advanced. Please follow all instructions properly.
- For infants less than 6 months old, always use distilled or boiled water cooled to room temperature.
- Never pour boiling/hot water in water tank. Use distilled, purified, or boiled water cooled to room temperature for infant formula preparation.
- Un boiled tap water and/or unsterilized baby bottles can potentially lead to adverse effects for the health of your baby.
- Only prepare one bottle at a time, feed immediately & follow all instructions carefully. Do not keep leftover formula mix.
- If your child was born premature, with low birth-weight or is immune defficient, please consult your pediatrician before using this machine.
Attention: Don’t take anything apart yet. Follow these steps before doing anything else.
- Place the Formula Pro® Advanced on the counter or other level surface and turn it around so the back is facing you.
- Remove the water tank from the back of the machine, wash it with warm soapy water and rinse thoroughly, then dry.
- Fill water tank with distilled or purified water suitable for infant formula preparation, or boiled water, cooled to room temperature.
- Place water tank back on base, turn the machine around so the front is facing you and then plug it in.
- The machine will beep once to tell you it’s powered on. You’ll also see the LCD display turn on.
Now let’s rinse the inside of the machine
- Get a cup or bottle larger than 300ml (10oz) and place it under the funnel.
- Press the “ml/oz” button on the control panel repeatedly until the LCD screen says “300ml (10oz)”
- Now press the “water only” button on the control panel. The Formula Pro® Advanced will dispense 300ml (10oz) of water.
- Dispose of the water dispensed, or use it to water your plants.
Now you can unplug the machine, remove all the parts shown on the next page and set-up your new Formula Pro® Advanced.
- Get familiar with the part names on the next page, then proceed with the set-up on the following pages.
Formula Pro® Advanced – parts
Disassemble and wash all parts (except the base) and dry thoroughly. Assemble as shown on pages 5 & 6
Set-up instructions
Set-up and cleaning videos available at elfe.com.
- Place the measuring wheel into the powder container, fitting it over the axle with the at side facing down.
- Make sure the holes in the measuring wheel are in the same position as shown above.
- Place the front edge of locking cover in the recess in the inside/front of the powder container, UNDER THE TAB.
- Fit hole in locking cover over top of axle. It will not lay completely flat.
- Make sure the locking cover & measuring wheel look like this when assembled.
- Now place the stirring wheel on the axle and push down firmly until you hear a click. Make sure the stirring wheel is snapped in place and does not lift up easily.
Preparing your rst bottle
- Carefully pour formula powder into the powder container. Wipe up any spilled formula powder.
- Make sure that the powder is filled between the MIN & MAX lines on the powder container.
- Place the powder container lid on the powder container and turn clockwise until it stops. This will engage the safety switch & lock the powder container onto the base. To remove the powder container, turn the lid counter-clockwise.
- Fit the drip tray on the base to fit your bottle height. Adjust it so the mouth of the bottle is as close to the funnel as possible. Push the drip tray firmly against the base to set it in place.
Formula Pro® Advanced – controls & operation
Temperature indicator symbols
Powder & water settings
- Make sure your Formula Pro® Advanced is plugged in.
- Press the “powder setting” button repeatedly to select your setting 1 – 10. It is essential that you choose the correct setting for your formula brand and type. Go to elfe.com to find the correct setting for your formula powder.
- Press the “ml/oz” button repeatedly to select the milliliters/ounces of water you want to dispense. Milliliter/Ounce size indicates water volume only. It does not include the volume of powder added when mixing.
- Press the “temp” button to select temperature. The temperature indicator will ash when heating and will stay solid when the set temperature is reached.
= Slightly warmer than body temperature
= Body temperature
= Room temperature
- Press the “start” button to dispense formula. The formula pro will remember the setting & milliliter/ounce size even if it is unplugged. You do not need to select a powder setting every time you make a bottle. You can always change the milliliter/ounce size or powder setting by pressing the buttons again.
- The Formula Pro® Advanced will dispense powder & water together, then stop automatically when dispensing is complete. Some clumping may occur with some formula powders inherently difficult to mix with water.
- PLEASE NOTE: The level will appear higher than the milliliter/ounce size selected because of added powder volume and/or variance in bottle markings. Example: 120ml (4oz) of water plus powder volume is approximately 135ml (4.5oz) depending on your formula powder type.
- Check for clumps and shake or stir the bottle if necessary. Check temperature and feed your baby.
- Recall the powder when the arms of the stirring wheel become visible. This is very important for accurate formula measuring.
Daily Cleaning Instructions
It is EXTREMELY IMPORTANT to clean the funnel after every 4 bottles made. This will keep your Formula Pro® Advanced dispensing accurately. Always make sure Funnel & Funnel cover are COMPLETELY DRY before using re-assembling.
- Remove Funnel & Funnel Cover by pulling out and down.
- Wash Funnel & Funnel Cover with warm, soapy water & rinse well. Dry completely before re-installing.
- Wipe the powder-dispensing hole on the underside of the powder container using a dry paper towel or soft dry cloth.
- Wipe any spilled powder off the base.
PLEASE NOTE: You don’t need to remove the powder container or the powder container parts for daily cleaning.
Monthly Cleaning Instructions
Once a month, give your Formula Pro® Advanced a thorough cleaning.
Please watch set-up and cleaning videos at elfe.com.
- Hand-wash all parts shown above with warm soapy water, rinse well and dry thoroughly.
- Hand wash water tank with warm soapy water, rinse well and dry thoroughly.
Monthly Descaling Instructions
You can leave the formula powder in the powder tank during the descaling process. To prevent mineral scale on the water heater inside your Formula Pro® Advanced, follow these easy steps:
- Remove the water tank, empty it and recall it with 600ml (20oz) distilled vinegar & 600ml (20oz) of purified water.
- Place the water tank on the base of the machine & place a cup larger than 300ml (10oz) under the funnel.
- Select 300ml (10oz) with the “ml/oz” button, then press the “water only” button to dispense.
- Empty the cup, place back under the funnel, then press the “water only” button again to dispense another 300ml (10oz).
- Now unplug the machine, remove the water tank, and empty it. Let the machine sit for 4 hours.
- Wash, rinse and ll the water tank to the max line with purified water, then place it back on the base.
- Plug in the machine, place a cup to catch 300ml (10oz) water and use the “water only” button to run an 300ml (10oz) cycle. Dispose of the water dispensed in the cup and then repeat this step to run the entire tank of purified water through the machine. When the “Low Water” indicator turns on, you’re done rinsing.
- Recall the water tank with distilled, purified, or boiled water cooled to room temperature and return to normal use.
Long Term Storage Instructions
It is EXTREMELY IMPORTANT to clean the machine and remove all formula powder residue before storage. If you’re going to store your Formula Pro® Advanced for later use, or will not use it for a while, please follow the instructions below:
- Remove the powder container parts, funnel, funnel cover, drip tray and water tank from the base.
- Wipe the base with a clean damp cloth and make sure to remove any and all formula residue. Dry the base well.
- Empty the powder container, wash all powder container parts, dry throughly, reassemble, & reinstall on the base.
- Follow the Monthly Descaling Instructions on page 12, steps 1-7 only. Do not remove or recall the water tank after step 7.
- Now place a cup to catch 300ml (10oz) water under the funnel, then press & hold the “water only” button for 5 seconds. Water will dispense continuously until the machine is completely empty, then stop automatically.
- Unplug the machine, remove the funnel, funnel cover and water tank, dry them both thoroughly and reinstall them on the machine.
- Your machine is now ready for storage. Pack the machine in its box, or enclose it in a bag to keep it dust free.
Error Codes
In the unlikely event of electrical component error or interruption during operation, the following codes will be displayed on the LCD screen. Pressing and holding the “stop” button will clear the code and operation should return to normal. If the code returns or is unable to be cleared, please contact Baby Brezza Customer Service.
Troubleshooting
Condition Possible Cause Machine will not start. Unit is unplugged. Make sure the plug is securely inserted into the power outlet. Funnel is removed or not fully inserted. Insert funnel or push front of funnel until flush with machine. Water level is below “MIN” line. Add more water to water tank. Powder container is removed or not fully seated. Make sure powder container is placed on base properly Powder container lid is not completely closed. Turn Powder container lid clockwise to close completely. See page 7, step 3 for details. Powder container lid is on backwards. Make sure tab on edge of Powder Container Lid is facing the back of the machine and engaged with safety switch. See page 7, step 3 for details. Water in Water Tank is too cold. ( Temp Symbol on LCD Flashing) Wait for water to warm up. Water in Water Tank is too hot. ( Temp Symbol on LCD panel is flashing) Wait for water to cool down. Temperature of dispensed formula is too cold. Water has not yet been heated to correct temperature. Wait for heater to warm water. Make sure selected temperature symbol stays on solid instead of flashing Funnel will not at all the way in Funnel Compartment.
Funnel cover is not straight on funnel and/or not pushed down completely. Align tab on front of Funnel Cover with notch in Funnel and push down Funnel Cover completely. Clean Funnel symbol is on, Formula Pro beeps when start button is pressed. Funnel and hole on underside of Powder Container require cleaning. Follow Steps on Page 11 to clean and dry Funnel and hole on underside of Powder Container. Too much powder dispensed. Locking cover is not installed correctly. Check locking cover and make sure the front edge is locked under the tab in the powder container. See page 6, step 6 for details. Incorrect powder setting selected. Make sure to select the correct setting number for your powder type. For details, go to: elfe.com
Not enough powder dispensed. Powder level in powder container is too low. Recall Powder Container with more powder Machine has not been cleaned well. Disassemble, clean by hand-washing, completely dry all parts and reassemble Silicone scraper is not installed correctly. Make sure silicone scraper is installed correctly. Incorrect powder setting selected. Go to: elfe.com to concern setting for your powder brand and type, then choose correct setting using the “powder setting” button on the control panel. Not dispensing water. Water Tank not fully seated. Push Water Tank down all the way on Base. Powder build-up on funnel cover & underside of powder container. Clean funnel, funnel cover and underside of powder container every 4 bottles. Frequent use without cleaning underside of powder container. See page 11 for details.
If you can not remedy problems by using the troubleshooting chart above, do not return your Formula Pro® Advanced to the store. Please contact Baby Brezza Customer Service at 1-800-667-8184 or email at: service@elfe.ca.
REFRENCE LINK
