Iluv Selfy Case Wireless Bluetooth Remote Camera Guide
OVERVIEW
Re-Linking:
If the shutter is inactive for 5 minutes, it will go into “Power off” mode. To use the shutter again, press and hold the button for 4 seconds to power it on and it will automatically re-link to your iPhone. Selfy™ can only be paired to one device at a time. If you want to pair to another device you need to cancel the initial pairing by going to the Bluetooth menu, pressing the
next to “iLuv Selfy” and clicking “Forget this Device”. You can now pair selfy™ to a new device using the standard pairing procedure. To re-link selfy™ to the original device you need to pair selfy™ again. Turn selfy™ on, make sure Bluetooth is activated on the original device, and then select “iLuv Selfy” when it appears on the device list.
FAQ
Q: How do I know if selfy™ is on or off?
A: The LED on selfy™ will blink every 4 seconds when it is on.
Q: When will selfy™ go into standby mode?
A: Selfy™ will go into standby mode if there is no activity for one minute. To wake it up and resume use, press the button once. The link between selfy™ and your device will be re-established within three seconds. If selfy™ has not been used for five minutes it will power down. To turn it back on, hold the button for four seconds.
Q: How do I turn off selfy™?
A: Selfy™ will automatically turn off if there is no activity for five minutes. The LED will blink three times and then stop blinking when it powers off.
Q: Why does pressing the shutter button on selfy™ raise my phone’s volume setting when I am not in camera mode?
A: Selfy™ is designed specifically to work with iOS by using the iPhone’s volume button to take pictures/videos. Since selfy™ is linked to the volume button, it will take pictures/videos in camera mode, but turn the volume up when outside of camera mode. To take pictures/videos with selfy™, just activate your phone’s camera app and press the selfy™ button.
Q: I just turned on/unlocked my phone, but how come I can’t take any pictures/videos when I use selfy™?
A: Selfy™ can only be used to take pictures/videos if your phone is in camera mode. After you turn on/unlock your phone, make sure selfy™ is paired to your phone, and then go into camera mode to use it.
Selfy™ is designed specifically to work with iOS by using the iPhone’s volume button to take pictures/videos. Since certain social media apps do not utilize the volume button’s shutter function, selfy™ will not work with those apps. However, most social media apps allow you to upload pictures/videos from your camera roll so any pictures/videos you take with selfy™ via your phone’s camera app can still be uploaded.
Q: How can I tell if the battery in selfy™ dies and what do I do when that happens?
A: The battery in selfy™ may be weak or dying if you experience issues such as a non-functioning LED and difficulty taking pictures/videos from a distance. To replace the battery, unscrew the circular battery cover on the back of selfy™ and install a new CR2032 lithium battery.
The CR2032 is a common type of battery that is shaped like a coin and can be found in most electronics stores. You may use any brand of battery as long as it is a CR2032. When you install a new battery, make sure you press it in fully so that it lies flat in the chamber. There should be an audible click when this is done correctly.
Battery Removal Installation
Troubleshooting:
If you are experiencing issues with the shutter operating properly, use a paper clip or pen tip to press and hold the RESET button located on the side of the unit for 2 seconds. If it still malfunctions, it may be due to a weak battery. Install a new CR2032 battery into the remote and try again.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement:
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without RF restriction.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help
