Euhomy-IM-12AR-Portable-Automatic-Ice-Maker-User-Manual-Feature-Image

Euhomy IM-12AR Portable Automatic Ice Maker User Manual

Euhomy logo

Euhomy IM-12AR Portable Automatic Ice Maker User Manual

Euhomy IM-12AR Portable Automatic Ice Maker User Manual

 PREPARING YOUR/ICE MAKER FOR USE

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property. Read all instructions before using any appliance.

  • Do not operate this, or any other appliance with a damaged cord.
  •  Do not run the power cord over carpeting or other heat insulators. Do not cover the cord. Keep cord away from traffic areas, and do not submerge in water.
  •  We do not recommend the use of an extension cord, as it may overheat and become a risk of fire.

GETTING TO KNOW YOUR UNIT

General instruction

Euhomy-IM-12AR-Portable-Automatic-Ice-Maker-User-Manual-Image-1

  1.  Cover
  2.  Control panel
  3.  Ice basket
  4.  Water Reservoir(below ice basket)
  5. Ice Shovel and Evaporator finger(behind Ice Shovel).
  6. Air outlet
  7. Water drain cap: at front btm side of the unit.
  8.  Ice Scoop

 OPERATING PROCEDURES & MAINTENANCE

Position of control panel & function

Euhomy-IM-12AR-Portable-Automatic-Ice-Maker-User-Manual-Image-3

a.Water shortage indicator
b. Ice-Full indicator
c. Power indicator
d. Button to turn on/off the unit.
e,f. Selected ice size displaying: Small and Large.
g. Button to select ice cube size

UNPACKING YOUR ICE MAKER

  1.  Remove the exterior and interior packaging. Check if ice basket and ice scoop inside. If any parts are missing, please contact our customer service.
  2.  Remove the tapes for fixing ice shovel, ice basket & ice scoop. Clean the tank & ice basket.
  3. Put the ice maker on a level & flat counter top without direct sunlight and other sources of heat.
  4. Allow one hour for the refrigerant fluid to settle before plugging the ice maker in.

CONNECTING YOUR ICE MAKER

  1. This unit should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the possibility of electric shock.
  2. Plug your appliance into an exclusive, properly installed, grounded wall outlet. Do not under any circumstances, cut or remove the third (ground) prong from the power cord.
  3. This appliance requires a standard 110-120 volt, 60Hz electrical outlet with three-prong ground.

CLEANING AND MAINTAINING YOUR ICE MAKER

  1.  Take out the ice basket.
  2. Clean the interior with diluted detergent, warm water and a soft cloth.
  3.  Then use the water to rinse the inside parts, and drain out the water by unplugging the drain cap on front bottom side.
  4. Dry the interior and exterior with a clean soft cloth.

USING YOUR/ICE MAKER

  1.  Open the cover, remove the ice basket and pour water into tank. Keep water level below the water level mark.
  2.  Press “Power” button on the control panel to begin the ice making cycle.
  3.  Select the ice cube size by pressing the “Select” button.
  4.  The ice making cycle lasts approx. 6 to 13 minutes, depending on selection of ice cube size and the room temperature. The recommended room temperature is 50° F to 100 ° F
  5.  If water pump can’t inject water, the ice maker will stop automatically, and the “Add Water” indicator will be on.Press “Power” button, fill water up to the max. water level mark and press “Power” button again to turn on the unit again.Allow the refrigerant liquid inside the compressor at least 3 minutes to settle before restarting.
  6. The ice maker stops when the ice basket is full and the “Ice” indicator will be on.
  7.  Change water in the water reservoir every 24 hours to ensure a reasonable hygiene level.

Leave a Reply