Kwikset HALO WI-FI Touchscreen Smart Lock Installation and User Guide
Parts List
Prepare the door and check dimensions
If drilling a new door, use the supplied template and the complete door drilling instructions available at kwikset.com/doorprep
- Make sure your door is compatible. If you have a standard deadbolt mounted separately from the handle below it, your door is compatible
- Remove your existing deadbolt from your door.
- Measure to confirm that the hole in the door is either 2-1/8* (54 mm) or 1-1/2* (38 mm).
- Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70 mm).
- Measure to confirm that the hole in the door edge is 1″ (25 mm).
- Measure to confirm that the door is between 1.3/8″ and 2″ (35 mm and 51 mm) thick
Install the latch and strike
- Is the door edge chiseled?
- Hold the latch in front of the door hole, with the latch face flush against the door edge.
- Which latch are you installing?
- Is the D-shaped hole centered in the door hole?
- Install the strike on the door frame.
Make sure the hole in the door frame is drilled a minimum of 1° (25 mm) deep.
Install the exterior keypad
- What is the diameter of the hole in the door?
- Locate the screws for step 3D and keep them within reach.
- Remove the mounting plate from the interior assembly.
- Install the exterior keypad and mounting plate.
Install the interior assembly
- Ensure the turn piece shaft is pointing up, and remove the interior cover and battery pack from the interior assembly.
- Install the interior assembly onto the mounting plate.
Install the batteries and perform the door handing process
This step will teach your lock the orientation of your door and is crucial to lock operation.
- Install 4 AA batteries in the battery pack.
- with the door open, install the battery pack to initiate auto-handing.
- After a few seconds, the latch bolt will retract and extend on its own to learn the orientation of the door. This is called the door handing process, and it is crucial to lock operation.
Test the lock and check door alignment
- With the door open, insert the key to extend the latch. Ensure that the latch extends smoothly.
- Turn the key 180° to retract the latch. Ensure that the latch retracts smoothly
- Close the door. Insert and rotate the key to lock the door. Ensure that the door locks smoothly.
- Turn the key 180° to retract the latch. Ensure that the door unlocks smoothly.
If your door does not lock and unlock smoothly, make sure you replaced your previous latch and strike with those supplied in the box. If you still experience locking errors, call Kwikset Support to order a Warped Door Service Kit. Kwikset Support: 1-800-327-5625
install the interior cover
Important Information about the interior cover
Cover Installation
Battery Pack Access
Download the app and create an account
The Kwikset app is needed to use this lock. If this lock was professionally installed (or installed by someone other than the homeowner), make sure this step is performed by the homeowner.
- Download the Kwikset app by scanning the QR code or visiting www.kwikset.com/app on your smartphone.
- Create your account and follow the setup instructions in the Kwikset app.
Halo Touchscreen at a Glance
System Alerts
Status LED colors
These features can be adjusted in some smart home apps.
Manual Door Handing
If needed, the door handling process can be initiated manually. This is useful if the lock is being moved tea different door
Network Reset
Network Reset will delete all Wi-Fi settings, Bluetooth pairings, user associations and remove the lock from the account
System Reset
System Reset will delete all access codes and lock settings including lock handing. The lock will run the handing process at the end of the System Reset
Factory Reset
Factory Reset will delete all Wi-Fi settings, Bluetooth pairings, user associations, remove the lock from the account, and reset all lock settings include handing.
Troubleshooting
A complete Halo Touchscreen Programming and Troubleshooting Guide is available at www.kwikset.com/halo/support
SmartKey Re-Keying
Re-key the lock to work with your existing key. See the supplied SmartKey Re-key instructions for more information.
Note: If Auto-Lock is enabled, remove the battery pack before re-keying your lock.
Important Safeguards
- Read all instructions in their entirety.
- Familiarize yourself with all warning and caution statements.
- Remind all family members of safety precautions.
- Protect your user codes.
- Dispose of used batteries according to local laws and regulations.
WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.
DOWNLOAD PDF LINK
https://www.kwikset.com/products/detail/halo-touchscreen-wi-fi-enabled-smart-lock
