Locky USA M210 Keyless Deadbolt Door Lock User Manual
INSTALLATION INSTRUCTIONS:
Step 1: Change User Code/Combination (OPTIONAL)
To change user code/combination, see instructions on reverse side.
Step 2: Prep Door for Installation with Template (If door is preprepped with 2 1/8” hole, use Bonus M210EZ Mount Kit and Instructions)
- Place template (supplied) on door and fold along door’s edge.
- Mark holes for 2 3/8” or 2 3/4” backset. Drill holes as instructed.
Step 3: Identify Door Handing (The M210 is pre-handed for right-hand doors)
- Right-Hand Doors – From exterior of door, hinges are on right-side (Fig. 1).
- Left-Hand Doors – From exterior of door, hinges are on left-side (Fig. 2).
- To change handing for left-hand doors, use a #1 phillips screwdriver to remove two blue screws and cover plate from Outside Body (Fig. 3).
- Move the handing pin from the right side of the outside body to the hole on the left side.
- Replace plate and screws.
Note: For M210DC – Inside Body must be handed opposite from Outside Body.
Step 4: Install Support Pin & Hex Bolts (Fig. 4)
- Install Brass Support Pin (#15) into either hole on Inside Body.
- Install/screw Hex Bolts (#14) into the top and bottom of the Outside Body.
Note: For M210DC — No support pin is used on double combination locks.
Step 5: Adjust Deadbolt (if necessary) & Install
- Adjustable Deadbolt (#12) is preset to 2 3/8” backset.
- To adjust, lift pin and slide to 2 3/4” (Fig. 5).
- With arrow pointed UP, insert Deadbolt and secure with two (2) Wood Screws (#9).
Step 6: Verify Correct Spindle Length (Fig. 6)
- With deadbolt (#12) installed, hold the Inside Body (#2) and Rubber Trim Plate (#3) to the door.
- Place Spindle (#5/6) through Deadbolt, into the Inside Body, as far as possible.
- Spindle should extend from exterior of door 3/8” min. to 5/8” max.
- If the 30-45mm spindle (#6) is too long, cut it to the correct length.
IMPORTANT:
- If spindle extends less than 3/8” it may not engage the lock.
- If spindle extends more than 5/8”, it will cause the lock to bind.
Step 7: Install the DIGITAL M210
- Place the Rubber Trim Plate (#3) on the backside of the Outside Body (#1).
- Place the Outside Body on the door. The hex bolts (#14) should extend into the top and bottom holes.
- The Support Pin (#15) on the Inside Body should extend through the hole in the Deadbolt (#12).
- Insert the Spindle (#5/6) into the Outside Body (#1) ensuring it’s in the proper angled position.
IMPORTANT: SPINDLE POSITION/ANGLE RIGHT-HAND DOORS: From inside, place spindle through Deadbolt, into the Outside Body (#1) in the 2:00/8:00 position. LEFT-HAND DOORS: From inside, place spindle through Deadbolt, into the Outside Body (#1) in the 10:00/4:00 position.
Using a screwdriver, secure the lock to the door with the Screws (#7 or #8). (Screw length is dependent on door thickness.) Test the operation of the Deadbolt by turning the inside thumbturn. Locate position where Deadbolt strikes door frame and install Mortised Strike (#4).
Test your M210 Digital Door Lock before closing the door:
- From Inside: Turn knob to lock, turn knob to unlock. For M210DC, use code to unlock.
- From Outside: Turn knob to lock, use combination to unlock.
NOTE: If combination is needed to lock, change handing (as described in Step #3). Your installation is now complete.
How to Change User Code/Combination
- Using a #2 screwdriver, remove the two (2) Red Screws.
- Carefully remove cover plate.
WARNING: Springs are attached to plate.
- TURN & HOLD thumb-turn to right or left 90° to release tumblers.
IMPORTANT: THUMB-TURN MUST be turned 90° and held when removing and inserting tumblers. Failure to do so will damage the lock and void the warranty.
WARNING: Do NOT force tumblers into position!
- With the thumb-turn held 90° to the right or left, remove/add CODE (Red) and NONCODE (Blue) tumblers to create the desired code. Ex: 3 Red = 3-Digit Code / 6 Red = 6-Digit Code
- After changing your code, release the thumb-turn to secure the tumblers in place.
- Replace the cover plate and secure with two (2) Red Screws, using a #2 screwdriver.
- TEST CODE before installing/re-installing lock.
REFRENCE LINK