Table of contents
show
Acebeam M1 Dual Head LED Flashlight User Manual
FEATURES
- Dual light source: 1x LEP, 3x LEDS
- Internal zoom design of LEP source, rotating the LEP head to adjust the focus without changing size. Beam angle 3~16°
- Max Output: 3500 lumens (LED): 700 lumens(LEP)
- Max Distance: LEP: 1600 meters(640000cd); LED: 231meters(13340cd)
- Impact resistance: 1m
- Waterproof: IP68, underwater 2m
- Battery: 1x USB 21700 Acebeam Li-ion
- Power Switch: ON/OFF and output modes cycle
- Function Switch: LEP/LED switching
INCLUDED
- 1× ACEBEAM M1;
- 1× ACEBEAM 21700 Type-C Rechargeable battery;
- 1x Type-C charging cable;
- 2xO-rings;
- 1xWarranty card;
- 1x User manual
SPECIFICATIONS
- Size: 104.0mm(Length)x 63.4mm(Head)x 60.3mm(Body)
- Weight: 304.6 g /10.7 oz (Including battery)
TECHNICAL PARAMETER
Notice: The above-mentioned parameters (tested with 1 XACEBEAM 21700 battery) are approximate and may vary from flashlights, batteries, and environments.
OPERATING INSTRUCTION
Dower Saitch Operatin
- ON: Click the Power Switch.
- OFF: Click the Power Switch when ON.
- Output Selection: When the LED light source option is ON, press and hold the Power Switch, and the LED light source will cycle from Low-Med 1-Med2-High, release the Power Switch to select the output, and can be memorized next ON;
- When the LEP light source option is ON, press and hold the Power Switch, and the LEP light source will cycle from Low-High, release the Power Switch to select the output, and can be memorized next ON;
- Turbo: In the Unlocked state and under the LED light source option, double-click the Power Switch quickly to enter the Turbo output, and double-click again to switch between Turbo and memory output;
- In the Unlocked state and under the LEP light source option, double-click the Power Switch quickly to enter the Turbo output, and double-click again to switch between Turbo and memory output;
- Strobe: In the Unlocked state and under the LED light source option, quickly press the Power Switch three times to enter the Strobe output;
- In the Unlocked state and under the LEP light source option, quickly press the Power Switch three times to enter the Strobe output;
- Ultra-low: When the flashlight is OFF and under the LED light source option, press and hold the Power Switch to enter the Ultra-low output;
- Ultra-low, Strobe, and Turbo modes of the LED light source option will be not memorized. Strobe and Turbo modes of the LEP light source option will be not memorized.
Lock/Unlock
- Lock: When the light is OFF, press and hold the Power Switch for 3 seconds, the current light source will flash 3 times, and the flashlight will be Locked. At this time, any switch operation will be invalid.
- Unlock: When the light is Locked, press and hold the Power Switch for 3 seconds, the current light source will flash 3 times, and then Unlock the light. If the current light source option is LED, the LED will be Ultra-low ON when unlocked, and if the current light source option is LEP, the LEP will be Low ON when unlocked.
- Function Switch Operation When the light is ON, click the Function Switch, the light output will switch between LEP light source or LED light source options.
LEP Zoom Operation
- When the LEP light source is ON, rotate the LEP head left or right, and the LEP beam angle will increase or decrease uniformly between 16° and 3°.
BATTERY VOLTAGE WARNING
- Green light: >20%
- Red light: among 20%~ 10%, low battery warning
- Red flash light: < 10%
The light would be turned off when the voltage is below 2.7V
LOW-VOLTAGE WARNING
With the lamp switched on, and the voltage drop below 10%, the lamp is programmed to Ultra-Low, to remind you to charge/replace the battery. When the 21700 battery voltage drops below 2.7V, the lamp will turn off automatically.
FAQ & SOLUTIONS
Problems
Causes
Solutions
Check if the switch is turned on correctly
Double Click to Turn on the Light
Check if it is assembled in place
Tighten the assembly parts
Abnormal
flash or
failure to turn on
Check if the battery is no power
Check if the battery is reversed
Check if the conductive position is dirty
Check if foreign matter falls in the tube
Part damage
Try the battery on other products
Remove the battery and reassemble it correctly
Clean the surface with alcohol
Pour out possible foreign matter
Contact your seller
Abnormal noise
WARNING
- CAUTION! Possible dangerous radiation! Don’t look into the light! May be dangerous for your eyes.
- By using this device, you certify you have read the included User Manual and Warning Card and release the manufacturer and retailers from all liabilities.
- Please use in accordance with applicable laws and regulations.
- Quality batteries with circuit protection will reduce the potential risk.
- Do not aim this light directly at eyes or exposed skin to prevent injuries. Keep this flashlight out of the reach of children.
USAGE AND MAINTENANCE
- Unauthorized disassembly may damage the light and void the warranty.
- This is normal case the light will accumulate a lot of heat when used on Turbo output levels for extended periods.
- Lubricate the threads with professional grade lubricant regularly.
- Please swap out the O-rings regularly to maintain the water resistance level.
- Maintain and keep clean any contact surfaces of the flashlight with alcohol swab. This may prevent irregular flashes during use.
- Remove batteries during storage. Keep lithium-ion batteries charges approximately every 4 months.
- This flashlight may not be used as diving light.
PRODUCT WARRANTY
- If the customer experiences any problems with an Acebeam product dwithin 15 ays of purchase, the dealer will replace that product.
- If an Acebeam flashlight fails during normal use within a period of five years (60months) of purchase, the dealer will repair or replace the flashlight with the same or similar model.
- ACEBEAM Batteries, accessories and lanterns with built-in batteries are warranted for a period of one year (12 months) from date of purchase.
- The warranty does not cover damage or failure caused by:
- Rough usage or operation which does not comply with the user manual or product specifications.
- Unauthorized disassembly, repair or modification. Defects or damaged caused by factors out of Acebeam’s control.
- Battery leakage damaged products.
- If there are any questions about ACEBEAM products, please consider the warranty and contact Acebeam or your original Acebeam dealer for warranty return instructions. Email: info@acebeam. com
REFRENCE LINK
