Package Contents 2 Before You Start
MAS200 User Manual
www.brinno.com
Take motion sensor unit out of door knocker casing.
1. Remove knocker ring.
Open front cover.
2. Open the front cover.
3. Take out motion sensor unit.
Complles with
IMDA Standards
N4232-17
4 Activate Motion Sensor
3 Device Parts
5 Display Icons 6 Sensor Installation
1. Door Knocker Casing
2. Motion Sensor Unit
(inside knocker casing)
3. Receiver Unit
4. Magnetic Wall Mount
5. Screwdriver
6. Battery Lock*
(inside motion sensor unit)
7. 1 CR2450 Battery
(inside motion sensor unit)
Receiver Unit:
For Camera:
For Motion Sensor Unit:
Motion
Sensor
Motion
Sensor
1
2
3 4 5 6
CR2450
7
2
3
1
1
2
4
5
1. Connected sensors:
The icon turns white to indicate the device is
successfully connected to the sensor.
Door Knocker Mode:
Insert motion sensor unit into door knocker casing
included in the package.
Portable Mode:
Hide motion sensor unit anywhere separately near
your front door.
1 2 3
4 5 6
Motion sensor unit
1
1 2
3 4
5
3
Motion Sensor Unit:
1. Motion Sensor Lens
2. Battery Compartment
3. Motion Sensor Pairing Channel Switch
4. Pairing Button
5. LED Indicator
* Keep battery out of reach of children. Install battery
lock to prevent children from swallowing battery.
2
1. Connector
2. LED Indicator
1 2 3
4 5 6
1 2 3
4 5 6
2. Sensor in low battery:
The icon turns red to alert battery dropping low.
Wait 30 secs for the sensor to be
auto paired. Motion sensor icon
will appear on the camera LCD
once activated.
Insert receiver unit. Turn on power.
If you choose to set up a multiple motion sensors
environment and purchase additional motion sensor
units, please refer to Multiple Sensors Part below for
full details.
Remove tab and engage
battery to activate motion
sensor.
2
3 4
8 9
10
Specications
Delete Sensor
7 Transmission/Detection Pairing Channels
Multiple Sensors
MAS200
90° (horizontal)
Centerline: 13 ft (4 m)
Side: 5 ft (1.5 m)
32 ft (10 m)
1 CR2450 battery (included)
Approx. 28,000 triggers
SHC1000, SHC1000W
Door knocker casing:
2.3″ x 3.8” x 1.1” ( 59 x 97 x 28 mm)
Motion sensor unit:
1.7″ x 2” x 0.5” ( 44 x 52 x 14 mm)
Receiver unit:
1.5″ x 1.1” x 0.2” ( 37 x 29 x 6 mm)
Door knocker casing:
1.3 oz ( 36 g)
Motion sensor unit:
0.7 oz ( 21 g) (without batteries)
Receiver unit:
0.2 oz ( 5.5 g)
Door knocker casing; Motion sensor unit
(inside knocker casing); Receiver unit;
Magnetic wall mount; Battery lock;
Screwdriver; 1 CR2450 battery.
Model
Detection Angle
Splash-proof IPX4
Detection Distance
Transmission Distance
to Receiver
Power Source
Battery Life
32 ˚F ~ 113 ˚F (0˚C ~ 45˚C) Operating
Temperature
Compatible Model
Size (WxHxD)
Weight
Package Contents
Transmission Distance:
32 ft (10m) between motion sensor unit and receiver
unit inside the camera. When you choose Portable
Mode, make sure the two units are within the transmission distance.
Sensor Detection Area:
Detection angle: 90 degrees (horizontal).
Detection distance: 13 ft (4 m) (centerline).
(approx. 5 ft (1.5 m) on both sides of the centerline).
One camera supports up to 6 motion sensors. You
make dierent channel combinations to identify each
unique motion sensor.
Motion Sensor Pairing Channel Switch:
Pairing Channel Combination:
ON
1 2 3
Channel 1:
ON
1 2 3
Channel 4:
ON
1 2 3
Channel 5:
ON
1 2 3
Channel 6:
ON
1 2 3
Channel 2:
ON
1 2 3
Channel 3:
3. Pair sensors.
Pin the pairing button
for 4~6 secs. (place the
motion sensor within
12 in (30cm)).
On motion sensor, LED
light ashes blue.
On receiver unit, LED light
ashes red.
On camera screen,
motion sensor icon
appears.
1 2 3
4 5 6
1
4~6 secs
32 ft
(10 m)
1. Motion Sensor takes around 30 secs to warm
up after sensor pairing is done.
2. Run motion sensor test and make sure the
camera is working properly.
www.brinno.com/support/registration
For manuals in other languages, visit
www.brinno.com/support
The product features, specications sheets and instructions may
dier from actual products. Please refer to Brinno ocial site for
the latest version of user manual.
ON
1 2 3
Channel 1 (default):
Time
2013/05/01
17:30
Set
Exit Press to Exit
Delete Sensor
Sensor 1
Delet all
Exit
Time
2013/05/01
17:30
Set
Exit Press to Confirm
CONFIRM: Delete
Sensor 1?
Yes
No
Press to Setup
Paired Motion Sensor
Sensor 1
1. The screen displays all paired sensors.
2. Select one sensor or all sensors to be deleted from
the list.
3. Press SHUTTER BUTTON again to delete.
Press SHUTTER
BUTTON to go to
the DELETE SENSOR
option.
Press SHUTTER
BUTTON to conrm
deletion.
4. Restart the camera. The selected sensor will be
permanently deleted.
1. Insert receiver unit into camera.
2. Turn the camera power on.
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
RF Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator
& your body. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
.
15.19 Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference and
2) this device must accept any
DOWNLOAD PDF
Brinno MAC 200DN Outdoor Security Camera User Manual
