Mee audio Bluetooth Wireless headphone system for tv User Guide
STEP 1
PACKAGE CONTENTS:
GETTING STARTED
- Plug the micro-USB power cable into the micro-USB POWER port of the Connect.
- Plug the USB end of the cable into an AC adapter, TV, or computer USB port.
CHARGE HEADPHONES
- Plug the micro-USB power cable into the micro-USB power port of the Matrix Cinema.
- Plug the USB end of the cable into an AC adapter, TV, or computer USB port.
- Charge for 2 hours
- Proceed to STEP 2
STEP 2
POWER ON AND CONNECT
The Connect transmitter and Matrix Cinema headphones are paired and ready to use and will connect automatically once powered on.
- Slide the ON/OFF switch of the Connect transmitter to the ON position.
- Slide the ON/OFF switch of the Matrix Cinema headphones to the ON position.
- A solid blue light will appear on the transmitter to indicate that a connection is established
A SOLID BLUE LIGHT ON TRANSMITTER INDICATES CONNECTION
- Proceed to STEP 3
STEP 3
CHOICE A: OPTICAL
- Remove protective caps from both ends of the digital optical S/PDIF audio cable
- Plug digital optical S/PDIF audio cable into the OPTICAL audio input of the Connect.
- Plug the other end into the TV’s DIGITAL AUDIO OUT (OPTICAL) port.
- Test for sound. Make sure the volume on both your TV and headphones is turned up.
- Proceed to STEP 4
- Change Sound Output to “Optical”**
- Change Digital Audio Output Format to “STEREO” or “PCM”**†
This may also need to done in the audio output settings menu(s) of your streaming app(s) and/or device(s) such as Apple TV®
**Exact menu and item names may vary between TVs. †On some TVs settings may be located in “Advanced settings” or “Expert settings” submenus.
- Proceed to STEP 4
CHOICE B: 3.5 MM
- Plug 3.5 mm audio cable into the 3.5 mm audio input of the Connect.
- Plug the other end into the TV’s headphone jack.
Headphone jack may be located on rear, side, front, or bottom of TV.
- Test for sound. Make sure the volume on both your TV and headphones is turned up.
- Proceed to STEP 4
CHOICE C: RCA
- Plug red/white ends of RCA audio cable into the TV’s red/white RCA AUDIO OUT port.
- Plug 3.5 mm end of RCA audio cable into the 3.5 mm audio input of the Connect.
- Test for sound. Make sure the volume on both your TV and headphones is turned up.
- Proceed to STEP 4
- Change audio output settings to “VARIABLE”.
- Set TV’s internal speakers to “OFF”.
**Exact menu and item names may vary between TVs.
- Proceed to STEP 4
STEP 4
ADJUSTING VOLUME
Tap the Volume Up or Volume Down buttons on the Matrix Cinema to adjust headphone volume
CHANGING AUDIO MODE
Tap the CinemaEAR button on the Matrix Cinema to enable CinemaEAR and to change the audio mode. There are four audio modes available:
Hold the CinemaEAR button for 3 seconds to disable the CinemaEAR audio enhancement feature
POWERING OFF
When finished listening, power off headphones until next use.
The Connect transmitter can be left powered on and plugged into USB power.
SUBSEQUENT USE
When ready to use again, simply power on the headphones and they will reconnect automatically
Do not put the Connect or your headphones into pairing mode.
A solid blue light on the Connect will indicate that a connection has been re-established.
NEED HELP? VIEW OUR VIDEO SETUP GUIDE
Scan QR code or enter the URL below into your web browser: MEEaudio.com/T1CMAVid
ADDITIONAL INFORMATION
OVERVIEW:
LED INDICATOR LIGHTS
The status of the Connect is shown by a green power / charging indicator light on the rear of the unit and two blue indicator lights on the top as follows:
PAIR NEW/ADDITIONAL BLUETOOTH HEADPHONES
This procedure is used to re-pair the Matrix Cinema headphones if they do not reconnect automatically, to pair a different headphone with the Connect transmitter, or to pair a second headphone when one is already connected. Note: Turn off all nearby Bluetooth devices, including TVs, phones, tablets, computers, etc. before beginning the pairing process.
- Put your Bluetooth headphones in pairing mode.
Matrix Cinema headphones: Slide the ON/OFF switch to the ON position, then hold the Multifunction button for about 5 seconds until the status indicator light begins to flash red and blue and the headphone says “Ready to Pair”. Other headphones: Consult the user manual of your Bluetooth headphones for the correct pairing procedure.
- Once the headphones are in pairing mode, click Pairing button “B” once to put the Connect in pairing mode.
Blinking blue light will change to solid blue light once successfully paired. If two headphones are paired, two solid blue lights will be shown.
FACTORY RESET/CLEAR MEMORY
To perform a factory reset of the Connect, power on the Connect and hold Pairing button “A” for approximately 5 seconds until the blue indicator light stops blinking. All previously paired devices will be cleared from memory and a new pairing will need to be created by following the pairing procedure above.
Left Earcup
- 3.5 mm audio jack
- Charging Indicator light
- Micro-USB charging port
Right Earcup
- Volume Up / Skip Track button
- Volume Down / Previous Track button
- Status Indicator light
- Multifunction button
- Power On/Off switch
- Microphone
- CinemaEAR button
CHARGING
The Matrix Cinema headphones should be charged roughly every 28 hours of use. Connect micro-USB cable to the charging port of the Matrix Cinema and a powered-on computer or USB charger. Charging time is 2 hours. The red charging indicator light will turn off once fully charged. Low battery is indicated by a flashing red status indicator light and “battery low” voice notification every five minutes.
PAIRING WITH OTHER DEVICES
The Matrix Cinema can be used as a headset when connected to phones and tablets. It will first need to be paired with each device. To pair the Matrix Cinema with a new device, power it on and put it in pairing mode by holding the Power / Multifunction button for about 5 seconds until the status indicator light begins to flash red and blue in an alternating pattern and the headphone says “Ready to Pair”. Open the Bluetooth menu on the device you wish to pair (usually located in Settings->Bluetooth). If needed, select “search for devices”, “add new device”, or “refresh.” Select “MEE audio Matrix Cinema” and allow pairing to complete. It is only necessary to pair your headphones once with each new device.
CONTROLS WITH PHONES AND TABLETS
The headphone controls on the Matrix Cinema are located on the right earcup.
*To start playing music, open a music app on your device and start playback. **Not all devices support this functionality. For more information, refer to the user manual for your device.
CHANGING AUDIO MODE
CinemaEAR is an advanced audio enhancement feature that allows for on-the-fly audio adjustment with four different hearing and sound enhancement modes:
Cinema EAR is disabled by default.
DISABLING AUDIO PROMPTS
The Matrix Cinema’s voice prompts can be disabled for uninterrupted listening.
*Standby mode: headphones are powered on but not connected to any Bluetooth device(s). While in standby mode, the blue status indicator light blinks every second
DISABLING STATUS INDICATOR LIGHT
The status indicator light on the right earcup of the Matrix Cinema can be disabled for uninterrupted use in low-light environments.
Note: the charging and low battery notification light on the left earcup cannot be disabled
FACTORY RESET
This can be used to restore all of the features of the Matrix Cinema to their factory settings. Before the headphones can be used again, a new pairing will need to be created.
VIEW OUR VIDEO SETUP GUIDE
Scan QR code or enter the URL below into your web browser: MEEaudio.com/T1CMAVid
QUESTIONS?
Get answers at MEEaudio.com/ConnectHelp View and download complete user manuals for Connect transmitter and Matrix Cinema headphones at MEEaudio.com/Support
WE’RE HERE TO HELP!
Phone Support: 626-965-1008
Monday ~ Friday 9:00 am to 5:00 pm PST
Email Support: support@MEEaudio.com
All emails are responded to within 2 business days
FCC RULES
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Relocate the receiving antenna.
- Increase the separation between equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
DISPOSAL AND RECYCLING
Dispose of this product in accordance with all local laws and regulations. Because this product contains electronic components and a battery, it must be disposed of separately from household waste. Contact local authorities to learn about disposal and recycling options.
DOWNLOAD PDF LINK
