MEES M1 TWS Wireless Earbuds User Manual
ACCESSORIES
Select one earbud as the main earbud
Remark: Make sure the other earbud is in the charging case
Quick press 2 times MFB
Red/Blue LED blinking and you will hear “Pairing”
Search the Bluetooth list from the device, and choose “M1(R) or (L)”
You will hear “connected” Pairing is done and succeeded.If require, Please input “0000” as the Bluetooth password
Pick up the other earbud from the charging case
You will hear “Power on” and “TWS connected”
M1 remember devices it’s not necessary to Repair, Enable Bluetooth on your device, it’ll reconnect automatically.
Note: All calls will be heard in the Main earbud only.
Best fit & best sound
Try all the ear tips to find the best fit and the best sound. The fit is right when you get a complete seal, the ear tips feel comfortable, a nd you get the best quality and loudest sound.
Insert the earbuds with the ear tip directed towards your ear canal. Twist gently until fit comfortably and feel secure in your ear.
Tip: More than one ear tips size may fit you. Choose the one that completely seals your ear canal for the best sound.You may need different size ear tips for the left and right.
M1 basics
Power On/Power off
Pick up earbuds from the charging case, and earbuds will be powered on automatically, and you will hear “Power on”Put the earbuds into the charging case, earbuds will be powered off and start to charge, and you will hear “Power Off”
Charge the earbuds
Put the earbuds into the case.
Push back the case until it is completely closed.
The earbud’s green light turns on when it is charging and light turns off when it is completely charged.
Charge the case
Charging the case by plugging in the charging cable. The case light turns on when it is charging.
Charge level
Your earbuds let you know when your battery level is low. Every 20 seconds you will hear“Battery low” when there is 2 minutes of battery level.
Earbud status lights
- Status Color
- Charging Red
- Fully charged Off
Case status lights
When your case is plugged into a charging cable for charging, you will see charging lights.
- Charging Slow blinking blue
- Full charge Steady blue light
Note: Your battery is designed to last life of the product. It should only be removed by a recycling facility. And attempt to remove or replace your battery will damage the product and void your warranty.
Basic Specifications of Earphone
- Size: 23.6×16.5×26.7mm
- Weight: 4.5g
- Earbuds Charging Current:55mA
- Earbuds Charging time: 1 hour
- Working Voltage: 3.3V~4.2V
- Standby time: about 40 hours Music Time:2~2.5 hours Talking Time:2 hours
- Bluetooth version: Bluetooth 4.2
- Support Profile: HSP, HFP, A2DP, AVRCP
- RF transmit: Class-2
- Transmission Range (Hz): 2.40GHz ~ 2.48GHz Transmission distance: 10m
- Audio sampling accuracy: 16bits
- Audio sampling rate: 44.1~48kHz
- Audio encoding format: CVSD、MSBC、SBC、AAC SNR: >95dB
- Working temperature: -15℃～+60℃
- Working humidity: 10%~85%( in a non-frozen state)
Earbud Speaker Specifications
- Speaker specifications / mode: Φ6mm
- Impedance: 16Ω/ TYP.
- Frequency(Hz): 20Hz～20KHz
- Sensitivity: 93±3dB
- Input Power: 2.0mW (Normal), 5mW (Maximum)
Earbud MIC Specifications
- MIC type: Silicon MIC
- MIC sensitivity: -42±3dB
- SPL：130dB
Basic Specifications of Charging Case
- Size: 59*34*24mm Weight:27g
- Charging Port: Micro
- Charging base(Full) provides power to earphone: 2 times Charging time: 2hrs
Safety instructions for use
To avoid hearing damage, keep the volume at a moderate level. Avoid listening to music at loud volume levels for prolonged periods of time as this may cause permanent hearing damage or hearing loss.
Do not use M1 when it is unsafe to do so. For example, while operating a vehicle, cycling, crossing a road, or any activity which requires your attention and ability to hear.
Note: If you are watching video while using your earbuds, your audio may be slightly out of sync with your device.
Safety Warning
Please disconnect the USB cable after charging. The product should not de charged in a long time.
Please use the charger or adaptor with output voltage and current(max) 5V/1A or 5V/1.5A and product original charging cable for the product charging. lf the output voltage and current of the charger exceeds the requirement,it will cause severe damage to the product, and the product warranty will be invalid.
REFERENCES
https://mees.co.jp/manual/manual_m1_e.pdf
