Frida Mom 2-in-1 Lactation Massager User Manual
Milk on the move
When the flowing gets tough, give each boob a 10 minute massage with the 2-in-1 Lactation Massager. Use it before
breastfeeding to get to the let-down faster. Use it during a feeding or pumping sesh to get that milk flowing and reduce pumping time. When taking on stubborn ducts, the different sides + ends will give you options to break it all up. Read on for more tips + good vibes.
How to Use
- Use the Targeted Tip to work out stubborn clogged ducts and break up the buildup.
- Move the milk with the Loop End by placing over the clogged area and gently pulling.
- Stimulate the breast with the Side Scooping Edge to soften the breast for latching and get milk flowing.
TURN IT OFF
Press and hold the Power/Vibration button to shut off the unit. This can be done at any time. Heads up, the next time you turn on your 2-in-1 Lactation Massager, the unit will start with whatever setting you previously used. E.g., Mode 2 with Pulse Vibration at its lowest intensity and Heat at its highest. Adjust the levels following the previous instructions to make a change.
Charging
When the battery level is low, the Power/Vibration button will flash red twice after being switched on. Charge the unit by plugging the USB cable jack into the port. Once the battery is full, the Power/Vibration button LED will return to white.
Note: The unit cannot be charged and used at the same time. If it’s plugged in while you’re using it, it will automatically shut off the vibration and heat and start charging instead. Don’t get stuck at 2 am with a dead battery. Charge it up beforehand!
Technical Data
- Product Name: 2-in-1 Lactation Massager
- Model: 127
- Input Voltage: 3.7V
- Charging voltage: 5V
- Power Source: USB
- Battery life: 80 minutes
- Weight: 67g (with battery)
- Dimensions: 115mm x 46mm x 32mm
Care and Cleaning
Clean massager after use. Use soapy water and rinse lightly or 70% alcohol swab. Do not submerge. Do not use abrasive cleaning agents, thinners or benzene for cleaning. Naturally air dry and avoid direct sunlight. Store in a clean, dust-free place.
Warning:
- Not a toy. Keep out of reach of children.
- Not to be used while breastfeeding.
- If skin irritation occurs, stop use and contact a doctor immediately.
This product is not intended to diagnose or treat any health problem or disease and should not be used as a substitute for the consultation and advice of a physician or other medical professional.
Operating Instructions
- TURN IT ON: Press Power/Vibration button for 2 seconds to turn the unit on.
VIBRATION MODE:
When you first turn on your 2-in-1 Lactation Massager, the default is Mode 1 – Constant Vibration. Mode 2 delivers a Pulse Vibration. Mode 3 uses an Oscillating Vibration. To switch modes:
- Press the Power/Vibration mode button 1x to select Mode 2.
- Press the button 1x for Mode 3.
- Press the button 1x to return to Mode 1 .
HEAT MODE:
The heat mode will be off the first time you turn on your 2-in-1 Lactation Massager. There are three levels of warmth.
105°F (40°C), 110°F (43°C), 114°F (45°C). To turn heat on:
- Press the Heat button 1x for low heat. The first light will activate.
- Press the button 1x for medium heat. The second light will activate.
- Press the button 1x for high heat. The third light will activate.
- Press the button 1x to shut the heat off. The lights will turn off.
USING HEAT ONLY:
- Press the Power/Vibration button for 2 seconds.
- Push the “-“ button until the vibration switches off.
- Follow the Heat Mode instructions above to pick the desired heat.
Troubleshooting
- My unit flashes red twice when I switch it on: This means your battery is below 20% and the massager needs to be charged.
- My unit isn’t turning on: Make sure that the charging port is plugged into both the unit and the plug all the way and that the power LED is flashing white so you know it is charging.
- My unit isn’t switching on when it’s plugged in to charge: The unit is designed not to work when it’s charging for safety and to preserve the battery. The white flashing light will turn solid when it’s fully charged. Unplug the unit and press the power button to use.
- Press the (+) to turn the vibration on. Check that the unit is switched on by holding down the power button for 2 seconds.