Monstrum PC120 Cyborg Prism Scope User Guide

Monstrum PC120 Cyborg Prism Scope User Guide

Your Package Includes:

For more accessories for your product, visit us online:

• PC120 CYBORG 1x Prism Scope
• CR2032 Battery
• Torx Wrench
• Lens Cloth

Parts Description

• A – Eyepiece
• B – Windage Adjustment
• C – Elevation Adjustment
• D – Battery Door
• E – On/Off, Illumination Dial
• F – Objective Lens
• G – Diopeter Adjustment

Installing Battery

The CYBORG Prism Scope comes with a CR2032 3V Battery. The battery can be replaced by removing the battery cap located at the end of the illumination dial. Insert it with the negative (-) face down. Be sure to tighten the battery door fully to prevent connection issues.

Operating Instructions

Illumination Controls

• Turn On: Press either the [+] or [-] buttons on top of the unit.
• Turn Off: Hold the [-] button down for 3 seconds.
• Reticle Color: Hold the [+] button down for 3 seconds to switch between Red and Green.
• Increase Brightness: Press the [+] button.
• Decrease Brightness: Press the [-] button. This sight has 11 illumination levels in both Red and Green. Brightness settings are saved to memory each time it is turned on and off.

Shake Awake

The red dot will automatically enter sleep mode when idle for 10 minutes.

Mounting the Sight

The scope features a built-in mount. The mount attaches to a 1913 Picatinny style rail. First loosen the mounting bolts with the included T15 Torx wrench, install into position on your weapon’s rail system, and then hand tighten plus 1/4 turn (approximately 30 in-lbs). The height of the optic center point is exactly 1.55 inches from the rail top.

Adjusting the sight

• This optic features 1/2 MOA windage and elevation adjustments located on the top and side. To adjust your aim, simply remove the caps and use the projected tab on the backside of the cap to rotate the dial.
• Elevation Adjustments: Top Dial. Adjust this setting if the point of impact is too high or too low from the target. Rotating this dial counter-clockwise will lower the aim point and raise your impact point. Rotating it clockwise will raise the aim point and lower your impact point.
• Windage Adjustments: Side Dial. Adjust this setting if the point of impact is left or right from the target. Rotating this dial counter-clockwise will move the aim point left and move your impact point right. Rotating it clockwise will move the aim point right and move your impact point left.

Maintenance & Cleaning

• This device is fully sealed and IPX7 waterproof. Make sure to fully tighten the caps to prevent moisture and dirt entering the internals.
• Always clean the lenses and surfaces with a clean microfiber cloth. Other materials may scratch the glass or surfaces.

Features

• Electronic Controls with 11 Levels of red and green illumination.
• Ultra LUX Multi-layer Lens Coating for a sharper image.
• Made of durable and lightweight 6061 Aircraft-grade Aluminum.
• Power saving Sleep-mode with Shake Awake.
• 1.55” High Aim point® Micro* compatable mount with Torx lockdown bolts.
• IPX7 Waterproof & Fog-proof rated for trouble-free performance.
• This product is provided with a Lifetime Warranty.

Specifications

• Magnification: 1x
• Objective: 20mm
• Length: 3.6in (92mm)
• Weight: 10.2oz (289g)
• Elevation Range: ±40 MOA
• Windage Range: ±40 MOA
• Adjustment Scale: 1/2 MOA/click

Troubleshooting

• Illumination is not turning on: Check to see if the Battery cap is fully tightened.
• Illumination is not bright enough: Try replacing the battery.
• Impact point is changing between groups: Check that the mounting bolts underneath the sight are tight. Make sure the rail mount is tightened sufficiently and that the sight does not move while installed on your weapon.
• Check Diopeter Settings: Look throught the optic at the reticle. It should appear sharp. Some prescriptions may make the reticle appear blurry. If so just adjust the Diopeter on the eyepiece to bring it into focus.

FAQS