MPOW MPBH129CB DWR20 Bluetooth Music Receiver Manual

MPOW MPBH129CB DWR20 Bluetooth Music Receiver Manual

Any issues during usage, please contact support@ibeeitzie.com to get professional services.

PACKING LIST

DIAGRAM

Power ON /OFF

On

1. Toggle to “ON”
2. Red light stays on for 1s
3. Red and blue lights flash alternately

Off

1. Toggle to “OFF”
2. DWR20 automatically turns off after the red light is on for 1s.

Bluetooth Connection

Connect with one mobile phone
Pairing mode. the indicator light flashes red and blue alternately. Successfully connected: the indicator light flashes blue intermittently. Enter the code “0000” if needed.

Connect with two mobile phones

• Step 1. After the first device is successfully connected, turn it off.
• Step 2. Operate the second device to connect with DWR20, then turn on the first connected

Clear the Bluetooth Pairing List: (on the power-on state) Press and hold on the button for about 8s and do not release it until the red and blue light stays on for 1s at the same time.

Play Music

Pause/Plav /Next Sona/Volume Up/Previous Sona / Volume Down

Answer / Hang up / Redial / Reject

Voice Assistant

Switch Audio Source

During a call: select a mobile phone or DWR20 to answer a call.

New Call During A Call

• Hang up one and answer another
• Hold on one and answer another

Low Battery Alarm

1. When the battery runs low, it will automatically alarm. The light flashes red 15 times quickly and then slowly
2. When the battery power is less than 3V, it will automatically shut down.

Charge

When the battery runs low or is unable to turn on, charge it.

Dormancy

1. If there is no operation or connection after the receiver is turned on, it will automatically enter sleep mode after 10 minutes. Click” ” button for 1 second or re-toggle the switch to wake it up. The power consumption of the dormancy state is about 10 A, the same as that in the state of shut-down.
2. When the connection between the receiver and the mobile phone is out of distance, it will automatically enter sleep mode after 20 minutes. Click ” ” button for 1 second or re-toggle the switch to wake it up.

Note:

1. The normal charging voltage range of the product is between 4.5V and 6.5V. Do not use any charging devices out of the range to avoid damage.
2. Please charge the receiver timely when the battery runs low or not be used for a long time to avoid that the product does not work properly or the battery is damaged.
3. Because the Bluetooth wireless signal is easily interfered with by the surrounding environment. blocked or absorbed by the objects, please place the Bluetooth receiver and the device in a barrier-free position for better Bluetooth wireless music transmission.

FCC Statement

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator& your body.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the /23 following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
•  Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

REFERENCE LINK