Nexvoo N120W Dual-Cam Android Video Conference Bar Guide
Packing List
- DoubleView Pro N120W
- Remote Control
- 12/2A Power Adapter
- 5m USB-C to USB-A Cable
- 1.5m USB-
- to USB-A Cable
- 1.8m HDMI Cable
- 1.5m Ethernet Cable
- Mounting Bracket and Accessories
- Warranty Card
- User Manual
Note:
We recommend that you use the accessories provided or approved by Nexvoo, using uncertified accessories may cause uncertain problems.
Product Introduction
- Mic Arrays
- Telephoto Camera
- 4K Ultra-Wide Camera
- Speaker
- Camera LED
- Power Connector(12V/2A)
- 3.5mm Audio Output
- HDMI Output 2
- HDMI Output 1
- USB-A Input 2
- USB-A Input 1
- RJ45 Ethernet Port
- USB-C Output
- Reset Port
Camera Indicator
Remote Control
- The remote control shall be equipped with two AAA batteries.
- You can press and hold “VOL-” and “ZOOM-” for 3 seconds at the same time, while the indicator light flashes. Double View Pro N120W will be connected to the remote control automatically. Once connected, the indicator light of the remote control will be off and the display interface will prompt “Remote Control Connected”.
Installation Instructions
Put on a flat surface
Mount on a wall
Placing DoubleView Pro N120W
Mount the DoubleView Pro N120W below the TV when the mounting height of the lower side of the TV is higher than 3.937ft(120cm).
Mount the DoubleView Pro N120W above the TV when the mounting height of the upper side of the TV is lower than 3.937ft(120cm).
Wall Mounting
Use the bracket to mount your endpoint on a wall. The mounting height affects your camera view. The recommended height is 1.1m above the ground.
Step1: Assemble the mounting bracket
Step2: Mount the DoubleView Pro N120W on the wall
Adjusting The Camera Tilt
Adjust the device angle after switching to the telephoto camera.
Powering On and Off
Double View Pro N120W doesn’t have a power button. When you plug in the power cord, the device turns on.
Connection and Usage
Connecting to the displayer
- Connecting DoubleView Pro and displayer through HDMI 1 Output port.
- Connecting DoubleView Pro to the power adapter, the device turns on.
- The network can be connected through an Ethernet cable or WIFI.
- Open video conference platform (for example Microsoft Teams, Zoom, …), successfully to the meeting, and turn on the camera when the green light remains on.
- Short press the Sleep button on the remote control to turn off the screen display when the meeting is over.
- Disconnect the power and turn off DoubleView Pro, if necessary.
Notes:
The default display connected to HDMI1 or HDMI2 output port is the same, whether different displays can be output depends on the video conferencing platform used.
Join the meeting quickly through DoubleView Pro’s Web Server:
- Connect DoubleView Pro and your computer to the same LAN network.
- Start the browser on your computer, enter the IP address of DoubleView Pro, and open the Web Server (such as http://192.168.1.100).
- Enter the meeting link on the Web Server page and click “Send” (for example, enter the Zoom meeting link).
- After DoubleView Pro receives the Zoom meeting link, it automatically opens the meeting link through the browser, selects and clicks “Launch App” via the remote control on the browser page, DoubleView Pro launches the Zoom App and automatically joins the Zoom meeting.
Connecting to computer
- Connecting DoubleView Pro to the power adapter, the device turns on.
- Connecting DoubleView Pro to the computer through a USB-C Output port
- Open the video conference platform on your computer (for example Microsoft Teams, Zoom, …), successfully connect to the meeting, and turn on the camera when the green light remains on.
- Disconnect the Doubleview Pro from the computer after the meeting.
Notes: During usage by connecting to the computer, there is no output from HDMI.
System Update
- Connecting DoubleView Pro and displayer through HDMI port to ensure network connected. The system will pop up an update notification, click the “Update” button to update.
Operating Ambient Temperatures
- Operating temperature: +32 to 104°F (0 to 40°C)
- Storage temperature: -13 to +160°F (-25 to +70°C)
- Relative humidity: 5% to 90%, non-condensing
Warranty
Our product warranty is limited only to the unit itself when used normally by the operating instructions and the system environment. We are not liable for damage or loss resulting from the use of this product or for any claim from a third party. We are not liable for problems with Nexvoo device arising from the use of this product; we are not liable for financial damages, lost profits, claims from third parties, etc., arising from the use of this product.
Explanation Of The Symbols DC
To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
Safety Instructions
Save these instructions. Read these safety instructions before use!
General Requirements
Before you install and use the device, read the safety instructions carefully and observe the situation during operation. During the process of storage, transportation, and operation, please always keep the device dry and clean, to avoid collision and crash. Please attempt not to dismantle the device by yourself. In case of any discrepancy, please contact the appointed maintenance center for repair. Please refer to the relevant laws and statutes while using the device. The legal rights of others should be respected as well.
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Third-Party Components
“Third Party Components” means certain software programs or portions thereof included in the Software or Hosted Service may contain software (including open source software) distributed under third party agreements (“Third Party Components”), which contain terms regarding the rights to use certain portions of the Software (“Third Party Terms”).
As required, information regarding distributed Android source code (for those products that have distributed Android source code) and identifying the copyright holders of the Third Party Components and the Third Party Terms that apply are available in the products, Documentation, or such successor site as designated by Nexvoo.
The open-source software license terms provided as Third Party Terms are consistent with the license rights granted in these Software License Terms and may contain additional rights benefiting you, such as modification and distribution of the open-source software. The Third Party Terms shall take precedence over these Software License Terms, solely concerning the applicable Third Party Components to the extent that these Software License Terms impose greater restrictions on you than the applicable Third Party Terms.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Product Information
Package Includes
- DoubleView Pro N120W
- Cable package
- Remote Control
- Wall mount
- User manual
Video Standards and Protocols
- H.264, H.265, VP8
Dual Camera System
- Ultra wide-angle camera
- 8M pixels
- f/1.8 aperture
- 5x digital zoom / EPTZ
- 120° FOV
- – Ultra HD 2160p (4K) capture resolution
- Telephoto camera
- 2M pixels
- f/2.0 aperture
- 3x digital zoom
- 58° FOV
- AI smart framing
- Auto Framing
- Speaker Tracking
- Face Recognition
- Camera indicator
Audio
- Audio processing technology
- Background noise elimination technology
- Beamforming directional pickup technology
- Multi-channel echo cancellation processing technology
- Multi-channel de-reverberation technology
- Long-distance full-duplex pickup technology
- Automatic gain control
- Mute/unmute control
- Audio codec: G.711, G.729AB, G.729A, G.722.2 (AMR-WB)
Operating System
- Video Mode
- Android 9.0
- Multimedia desktop design
- Support video conferencing systems, including Zoom, Microsoft Teams, etc.
- USB Mode
- Provide USB camera for PC, up to 4K@30fps
- Provide USB Audio for PC
