You are currently viewing LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide

LTC-logo

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide prdict img

Basic Information

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 1

BT MODE

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 2

Long Press FN+1/2/3 Three Seconds For Pairing Mode.

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 3

Short Press FN+1/2/3 Alone To Switch BT Devices.

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 4

2.4GHZ MODE

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 5

  • Short Press EN+4 To Switch To 2 4GHz Mode.
    LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 6
  • Long Press FN+4 Three Seconds If You Need To Repair The Dongle.
    LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 7
    Place the keyboard as close as possible to the USB receiver.

WIRED CONNECT

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 8

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 9

System Requirements

  • Computer with available USB ports
  • Compatible with Windows 2000 or above and Mac operating system

BASIC CONTROL

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 10

MULTIMEDIA KEY FOR WINDOWS
Windows System: Press Fn+A

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 11

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 12

MULTIMEDIA KEY FOR MAC
Mac System: Press Fn+S

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 13

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 14

KEYBOARD STATE

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 15

Check the Battery

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 16

LTC NB831 Wireless Hot Swappable Mechanical Keyboard Guide fig 17

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable
exposure condition without restriction.

REFERENCE LINK

https://ltcofficial.com/products/ltc-nb831-wireless-75-triple-mode-hot-swappable-mechanical-keyboard

Leave a Reply