Nutribullet NBJ50300 Slow Juicer User Manual
Important safeguards.
Warning! To avoid the risk of serious injury, carefully read all instructions before operating your nutribullet®. When using any electrical appliance, basic safety precautions should always be observed, including the following important information.
Save these instructions!
FOR HOUSEHOLD USE ONLY
- GENERAL SAFETY INFORMATION
- This juicer system has moving parts, and is not intended for use by children or persons with reduced physical, sensory, or mental capabilities, or who lack experience and knowledge of its safe operation. Such persons require close supervision and thorough instruction on its proper use and safe operation.
- Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance. Keep cord out of reach of children. This appliance is not a toy.
- To protect against fire, electrical shock and injury to persons, do not immerse the appliance, motor base, cord, or plug in water or any other liquid.
- Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning or attempting to move the appliance.
- To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.
Avoid contact with moving parts.
- Regularly inspect the power cord, plug, and entire appliance for any damage.
- Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner.
- Contact NutriBullet® customer service for assistance at 1 (800) 523-5993.
- The use of attachments not recommended or sold by NutriBullet® may cause fire, electric shock, or injury.
What’s included
Assembly guide
Before first use
Before using your juicer for the first time, please take a moment to perform the steps below.
UNPACK
Open the box and remove the appliance with its various components, placing all parts on a flat, level surface.
SEPARATE
A few parts will be packed together. Separate them using the following 3 steps (see image):
- a. Lifting up, remove Grinding Assembly and Rotating Bowl Brush together from the Juice Bowl.
- b. Detach Rotating Bowl Brush by moving it down.
- c. Lifting up, remove the Auger from Juicing Screen.
CLEAN
Immerse all detachable parts and accessories (not the base) in warm, soapy water. Rinse and dry.
Clean the outside of the base with a clean, damp cloth.
WARNING: Never submerge the Motor Base in water or any other liquid.
Usage instructions
- Prepare foods for juicing, and make sure nonjuiceable foods are not used.
- Remove any hard seeds, pits, and skin – for example, peel and pits should be removed from oranges, lemons, grapefruits, and melons.
- Cut foods into smaller pieces if needed to fit into the feed chute.
- Do not attempt to process thick or hard foods that don’t contain any juice to extract (for example, it is not recommended to process bananas, avocados, coconuts, or similar hard foods, since these may damage the motor).
- Before plugging the power cord into an outlet, make sure the power switch is in the “OFF” position.
- The power switch has three settings. Pressing the power switch to the “ON” position activates the motor and starts making juice; pressing the power switch to “OFF” turns off the machine; and “REV” means reverse rotation, only used when something is stuck and you need to unclog the unit.
- Make sure the juice and Pulp Containers are in their proper positions.
Juicing tips
PROPER PRODUCE PREP
- Prepare fruit and veggies before inserting them into the juicer:
- Clean produce properly. Rinse with lukewarm water, produce wash, or water and apple cider vinegar.
- eel or remove skin as needed. Foods with thick or hard skin must be peeled before being put into the juicer.
- Remove rind from all citrus fruits before juicing.
- Remove large pits and seeds from stone fruit before juicing. Stone fruit may be used only if the seeds or pits have been removed. Fruit with hard cores must be pitted. The cores of peach, plum, mango, and apricot should not be put into the feed chute, to avoid any potential malfunction.
- Chop food items down to the right size – small enough to fit easily into the feed chute, without having to force pieces down with the Food Pusher.
- Foods with less moisture and hard fiber: Cut into slices.
- Leafy vegetables and foods with long, hard fiber (such as celery and kale): Cut the stems into 4 inch pieces and then roll up the leaves well.
- For efficient juicing, alternate feeding soft foods and hard foods into the feed chute. For example, follow leafy greens with an apple slice, or an orange with a carrot. The harder produce will help with processing the softer produce and extract more juice.
- Frozen food items can be put in the juicer after being defrosted.
Troubleshooting
PROBLEM: PARTS ARE DIFFICULT TO DISASSEMBLE
Solution: After finishing juicing, in order to detach and clean parts more easily, continue to run the juicer for about 30 seconds without adding any additional food in order to process any food that might be stuck in the Auger and Juicing Screen. Another tip: after you are done extracting juice, pouring some water in the feed chute to clean it can help make it easier to disassemble.
PROBLEM: ARE DIFFICULT TO DISASSEMBLE Solution: After finishing juicing, in order to detach and clean parts more easily, continue to run the juicer for about 30 seconds without adding any additional food in order to process any food that might be stuck in the Auger and Juicing Screen. Another tip: after you are done extracting juice, pouring some water in the feed chute to clean it can help make it easier to disassemble.
Solution: If the juicer is stuck and not operable, press the power switch to the “OFF” position. Then press the RESET switch, which is located at the bottom of the base (see image). Next, press and hold the power switch in the “REV” position for few seconds, then try operating again.
If this reverse function does not work, turn off the machine, unplug, and reassemble it, using the instructions given earlier in this guide. After reassembly, try turning on the machine to see if normal function has been restored.
PROBLEM: THE JUICER TURNED OFF IN THE MIDDLE OF JUICING.
If the motor overheats, the juicer will turn off. Solution: If the juicer is overheated and stops working, unplug it and allow it to cool down for at least fifteen minutes before attempting to use again.
Care and maintenance
Cleaning the NutriBullet® Slow Juicer is quick and easy. All parts (except for the base) can be cleaned by simply rinsing with warm soapy water, or most parts are dishwasher safe. Here are some tips for cleaning and best practices.
- Always make sure the base is unplugged before you begin assembly, disassembly, cleaning, or storage of the unit.
- Detach and separate the parts of the juicer (see Disassembly section).
- Empty the Pulp and Juice Containers (store or throw away pulp, store or consume juice).
- Clean the Juice Bowl Cover, Food Pusher, Auger, Juicing Screen, Rotating Bowl Brush, Juice Bowl, and the juice and Pulp Containers under running water.
- Clean all juicer parts, except for the Motor Base, in warm, soapy water. Or, you can put all parts into the dishwasher except for the Auger.
To order additional parts and accessories, please visit our website at nutribullet.com/shop/accessories or feel free to contact Customer Service: 1 (800) 523-5993. thoroughly with the narrow end of the Cleaning Brush. The narrow end of the Cleaning Brush is sized so that it can fit inside of the pulp spout to help remove pulp that has been stuck. Run water through the bowl and pulp spout to help remove any remaining pulp.
NutriBullet® Select one-year limited warranty
LIMITED WARRANTY FOR NUTRIBULLET®
NutriBullet’s limited warranty obligations are confined to the terms set forth below:
NutriBullet, LLC (“NutriBullet”) warrants this NutriBullet® against defects in materials and workmanship for a period of one year from the date of original retail purchase. This limited warranty is valid only in the country in which the product is purchased and comes with the product at no extra charge, however shipping and processing fees will be incurred for returns, replacements and or refunds.
If a defect exists, and NutriBullet® is obligated under this limited warranty, at its option NutriBullet® will (1) repair the product at no charge, using new or refurbished replacement parts, (2) exchange the product with a product that is new or that has been manufactured from new or serviceable used parts and is at least functionally equivalent to the original product, or (3) refund the purchase price of the product. A replacement product assumes the remaining warranty of the original product. A repaired product has a one-year warranty from the date of repair. When a product or part is exchanged, any replacement item becomes your property and the replaced item becomes NutriBullet’s property. When a refund is given, your product becomes NutriBullet’s property.
OBTAINING WARRANTY SERVICE
For limited warranty service, simply call our customer service department at 1-800-523-5993 or contact us via email from our website at nutribullet.com, simply click the contact us link, fill out and submit the customer contact form and we will be glad to help you. When you contact our customer service department you will be asked for your name, address, telephone number and to provide proof of the original purchase (receipt) containing a description of the product(s), purchase date, and the appropriate NutriBullet® serial number(s).
Before you send your product for limited warranty service please make sure to keep a copy of all relevant documents for your files (receipt, etc.). It is always recommended to purchase product insurance and tracking services when sending your product for service. Remember, shipping and processing fees will be incurred and are not covered by the one-year limited warranty.
DOWNLOAD LINK
https://nbmedia.imgix.net/NBJ50300_NB_Slow-Juicer_User-Guide_LoRes-PROOF_F210216-2021-0412.pdf?dl
