Insignia NS-HW36A2P USB Charger User Manual
PACKAGE CONTENTS
- 3.6A USB Charger Wall Outlet
- White decora-style wall plate
- Wall plate screws (2)
- Outlet mounting screws (2)
- Quick Setup Guide
FEATURES
- Replaces a standard duplex outlet
- Quickly charges USB devices
- Tamper-resistant outlets for added safety
- Provides two USB ports with 3.6A total output
- Provides two standard 110V power outlets
- Works in nearly all installations
- Compatible with your existing Decora wall plate.
We recommend that you use a professional electrician to install the USB charger wall outlet.
SAFETY
Warnings:
- RISK OF ELECTRIC SHOCK — Use only in dry locations and only indoors.
- All cables should be routed away from the charger outlet openings.
- DO NOT use any aquarium equipment.
- DO NOT install in an outlet that is not grounded.
Notes to the installer:
- This device must be installed in accordance with National and Local electrical codes.
- To prevent severe shock or electrocution, always turn the power OFF at the service panel before working with the wiring.
- This device should be used with copper or copper-clad wire. DO NOT use aluminum wire.
- DO NOT install this device into a shallow wall box. The wall box must be deep enough to house the charger outlet. If the box is too shallow, the charger outlet will not fit securely into the wall.
- Professional installation is not a requirement but is highly recommended.
- Installer should use the screws that were used to install the existing outlet.
INSTALLING THE OUTLET
Warning: DISCONNECT POWER. Failure to do so can result in severe injury or death.
- Make sure that you disconnect power to the circuit by removing the fuse from the circuit or turning OFF the circuit breaker.
- Remove the wall plate and mounting screws that cover the old outlet.
- Carefully remove the existing outlet from the wall box.
- Disconnect the wiring from the old outlet. Note the wire positions.
- Connect the wires to the outlet:
- Black lead attaches to the hot wire(s)
- White lead attaches to the neutral wire(s)
- Green lead attaches to the ground wire(s)
Note: Installers should use previous wire positions as a guide.
Insert the straightened wire into either of the two holes of the hot and neutral locations on the side of the outlet. Power passes between the two corresponding holes for pass-thru wiring. Attach the ground wire to the bottom of the outlet.
- Tighten every screw and make sure that no bare copper wire is exposed.
- Carefully insert the outlet into the wall box.
- Secure the outlet to the wall box with the two long screws (provided).
- Secure the wall plate to the outlet with the two short screws (provided).
- Restore power by replacing the fuse or turning on the circuit breaker. The outlet is ready to use.
USING THE OUTLET
- To charge USB devices (like mobile phones or tablets), plug USB cables into the USB ports on the outlet and into the USB ports on the devices.
- To power electrical devices (like lamps or laptops), plug them into the electrical outlets.
SPECIFICATIONS
Dimensions (H × W × D)
- With plate: 4.7 × 3 × 1.9 in. (120 × 76 × 47.5 mm)
- Without plate: 4.2 × 1.7 × 1.9 in. (106 × 43 × 47.5 mm)
Electrical
- Receptacle rating: 15Amp, 125VA
- USB rating: Two USB ports with a total of 3.6A, 5V DC
- Line voltage: 125V AC @ 60Hz
- Wire terminals: #14-#12 AWG
LEGAL NOTICES
FCC Statement
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, maybe cause harmful interference to radio communications.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Industry Canada Compliance
This device complies with Industry Canada’s licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produice de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
ONE-YEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its affiliated companies Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2016 Best Buy. All rights reserved. Made in China
REFERENCE LINK
https://www.insigniaproducts.com/pdp/NS-CH1IPC8/5971603
