Insignia NS-RMT2D18 2-Device Universal Remote User Guide
PACKAGE CONTENTS
- 2-Device Universal Remote
- Quick Setup Guide
FEATURES
- Works with a TV and a set-top box
- Programming by popular brand names for quick and easy setup
- Extensive code library for less common brands and devices
- Premium design, materials, and construction for rugged use
INSTALLING BATTERIES
- Insert two AAA batteries (not included) into the remote. Make sure that the and symbols match the and symbols in the battery compartment.
Note: To set up your remote, follow the setup steps below, in order, and STOP as soon as your remote works correctly.
PROGRAMMING YOUR REMOTE
There are three ways to set up your remote:
- Use “Setup method A: Popular brands” for pre-set popular brands.
- Use “Setup method B: Direct code entry” if your device’s direct code is located on the back page.
- Use “Setup method C: Code search” to perform a code search for your device.
Note: This remote comes pre-set for Insignia TVs and DIRECTV set-top boxes.
Setup method A: Popular brands
- Turn on your target device.
- Press and hold SETUP until your remote’s LED blinks twice.
- Press TELEVISION or CABLE / SATELLITE / STREAMING to select the mode you want to set up. The LED stays lit.
- Press either 0 (for streaming/ cable/satellite) or 1 (for TVs) to select the device type you want to set up.
- Find your device type and brand in the table below, then press and hold its number until your device turns off . Release the key when your device turns off . Setup for that device is complete.
Note: If your brand does not appear in the table below, use “Setup method B: Direct code entry” or “Setup method C: Code search.”
Setup method B: Direct code entry
- Turn on your target device.
- Press TELEVISION or CABLE / SATELLITE / STREAMING to select the mode you want to set up.
- Press and hold SETUP until your remote’s LED blinks twice.
- Enter the fi rst 5-digit code for your brand from the code list (see TV CODE LIST on page 11).
- Press the (power) button to test your device. If the device turns off , setup is complete.
- If the device does not turn off , repeat steps 2-5 using the next code for your brand or use “Setup method C: Code search.”
Setup method C: Code search
- Turn on your target device.
- Press and hold SETUP until your remote’s LED blinks twice.
- Press TELEVISION or CABLE / SATELLITE / STREAMING to select the mode you want to set up.
- Press either 0 (for cable/satellite streaming) or 1 (for TVs) to select the device type you want to set up.
- Press and hold OK until your device turns off . Release the key when your device turns off . Setup for that device is complete.
USING YOUR REMOTE
- Press TELEVISION or CABLE / SATELLITE / STREAMING for the device you want to control.
- Press the buttons applicable to that type of device.
Watch TV mode
Note: To control a soundbar or other audio device with your remote, see Adding an audio device. While watching TV in CABLE / SATELLITE / STREAMING mode, you can:
- Use your remote’s volume and input buttons to control the TV. The rest of the buttons will control the device you’ve added to CABLE / SATELLITE / STREAMING mode.
- Press (power) once to turn your set-top box on or off . OR
- Press and hold (power) for two seconds to turn both your set-top box and your TV on or off . To turn off watch TV mode:
- Press and hold SETUP until your remote’s LED blinks twice.
- Press CABLE / SATELLITE / STREAMING twice. The LED blinks four times. Watch TV mode is turned off and your remote will not control your TV.
To turn on watch TV mode after turning it off :
- Press and hold SETUP until your remote’s LED blinks twice.
- Press CABLE / SATELLITE / STREAMING twice. The LED blinks twice. Watch TV mode is turned back on and your remote will control your TV again.
ADDING AN AUDIO DEVICE
If you listen to sound through a connected audio device (for example, a soundbar or audio/ video receiver), you can program your remote to control it when in CABLE / SATELLITE / STREAMING mode:
- Use “Method A: Popular audio devices” if your audio device is listed as a popular brand, or
- Use “Method B: Audio device code entry” to perform a code search for your device.
Method A: Popular audio devices
If Watch TV mode has been turned off , it is possible to lock volume controls to one device such as a TV.
To do this:
- Turn on your audio device and play something through its speakers.
- Press and hold SETUP until your remote’s LED blinks twice.
- Press MUTE.
- Find your audio device’s brand and corresponding number in the table on the next page.
- While aiming the remote at your audio device, press and hold your audio device’s number (from step 4) until the device turns off . Setup is complete and your remote controls your audio device’s volume while using a streaming, cable, or satellite device.
Method B: Audio device code entry
- Turn on your audio device and play something through its speakers.
- Press and hold SETUP until your remote’s LED blinks twice.
- Press MUTE.
- Find your audio device’s brand in the code list (see AUDIO CODE LIST on page 54), then use your remote to enter the fi rst 4-digit code for your brand from the code list.
- Press MUTE to test your audio device. If the sound mutes, setup is complete and your remote controls your audio device’s volume while using a streaming, cable, or satellite device.
- If the sound doesn’t mute, repeat steps 2-5 using the next code for your brand.
Unlocking volume controls
- Press and hold SETUP until your remote’s LED blinks twice.
- Press 9, 9, 3, then press VOL .
LOCKING AND UNLOCKING CHANNEL CONTROLS
The channel control lock lets you lock channel controls (Channel Up and Down, Digits, Enter, and Last) to either a TV or a cable/satellite/ streaming device.
Locking channel controls to one device
- Press and hold SETUP until your remote’s LED blinks twice.
- Press 9, 7, 3, then press CH .
- Press TELEVISION or CABLE / SATELLITE / STREAMING to lock channel controls to that device. The LED blinks twice.
Unlocking channel controls
- Press and hold SETUP until your remote’s LED blinks twice.
- Press 9, 7, 3, then press CH -. RESETTING REMOTE TO FACTORY DEFAULTS
- Press and hold SETUP until your remote’s LED blinks twice. 2 Press 9, 7, 7.
REMOTE OVERVIEW
TROUBLESHOOTING
ONE-YEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico) www.insigniaproducts.com
DOWNLOAD PDF LINK