Table of contents
show
Insignia NS-SDSKB553 55″ Black Standing Desk User Guide
Safety information
CAUTION:
- Unplug the power plug before cleaning. Wipe the dust from the surface with a slightly damp cloth. Be careful not to let the internal parts get wet. Do not loosen the adapter, switch, or motor connectors.
- The electric box contains electronic components, metals, plastics, wires etc., so dispose of it in accordance with each country’s environmental legislation, not with the general household waste.
- Check carefully to ensure correct and complete assembly before using.
- Be familiar with all functions and program settings of the product before first use.
- Children are forbidden to play on the product because of unforeseen action when playing, so any dangerous consequences caused by this improper action will not be on manufacturers.
- Slight noise caused by the V-ribbed belt or brake system due to structure will not have any effect on the use of the equipment.
- Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure that the cleaner used will not pollute the environment.
- This appliance can be used by children aged from 7 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
- Cleaning and user maintenance shall not be made by children without supervision.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid a hazard.
- Please make sure there are no hazard sources in your operating environment. e.g., do not litter the tools around. Always be careful to treat the packaging materials in order to avoid any possible danger, e.g. plastic bag may lead to choking hazard to children.
- Keep the original package of the equipment if necessary in case of the future use in transportation.
Features
- Adjusts electronically up to 48.4 in. (123 cm) to move between standing and sitting
- Easy to access switch effortlessly raises or lowers the desk height
- Memory function remembers up to four different height positions
- Steel frame with particle board tabletop provides a stable work surface and holds up to 110 lbs. (50 kg)
- Hardware included for quick and easy assembly
Dimensions
Parts included
Hardware included
Preparing to assemble your desk
- Make sure that all parts and hardware are included.
- To prevent product damage, assemble your desk on a carpet.
- Have another person help you with lifting and assembly.
- For the best results, do not fully tighten the screws until you have assembled all the other parts.
Assembling your desk
STEP 1: Install the columns
You need:
- Turn the tabletop (1) face down on a carpet to prevent scratches.
- Align the hooks on one column (2) with the screw holes on the column facing the front and back of the tabletop, then insert the post on the column into the post hole on the tabletop.
- Rotate the column counter-clockwise until the column hooks are under the pre-installed screws on the tabletop.
- Insert two short hex-head screws (A) through the screw holes on the column and into the tabletop. Tighten the screws with the 4 × 4 hex wrench (C).
- Repeat these steps to install the other column.
STEP 2: Install the feet:
- Align the screw holes on the bottom of one foot (3) with the screws on the end of the column.
- Insert four long hex-head screws (B) through the holes on the foot and into the holes on the column, then tighten the screws with the 4 × 4 hex wrench (C).
- Repeat these steps to install the other foot.
STEP 3: Install the switch
You need:
- Place the switch (5) on the tabletop with the buttons facing the front of the tabletop. Align the screw holes in the switch with the screw holes in the tabletop.
- Insert three switch screws (9) through the holes on the switch and into the holes on the tabletop. Tighten the screws with the 5 × 5 hex wrench with Phillips head (D).
STEP 4: Install the adapter
You need:
- Slide the adapter (6) into the adapter bracket. Make sure that the adapter connector points to the nearest column.
Note: For clarity, the adapter shown below is viewed from the switch side of the tabletop.
STEP 5: Connect and tie down the cables
You need:
- Plug one end of the adapter cable (7) into the adapter connection, then plug the other end of the cable into the DC IN port on the switch.
- Plug the motor cable on the bottom of the tabletop into the M1 port.
- Plug the power cable (8) into the connector on the adapter.
- Open a cable tie (4), slide the base of the tie under a cable, loop the cable tongue over the top of the cable, then slide the end of the tongue into the tie bracket.
You can attach the cables to the bottom of the desktop with the provided cable ties.
Using the switch
Adjusting the height
- Press the
(up) button to raise your desk or press the 
(down) button to lower your desk.
(up) button to raise your desk or press the 
(down) button to lower your desk.Note: The LED shows the height for 10 seconds.
Saving a height position
Your can save four height positions.
- Adjust your desk to the height you want to save. The LED shows the height for 10 seconds.
- Press and hold a height position button (1, 2, 3, or 4) for three seconds, then release the button. The height position is saved and the LED shows S-1, S-2, S-3, or S-4.
- To automatically adjust the height of your desk to the saved position, press 1, 2, 3, or 4.
Adjusting the anti-collision sensitivity
- When the lifting system’s built-in sensor encounters resistance, the lifting system pauses, then reverses motion and stops.
- Simultaneously press and hold the (up) and (down) buttons for five seconds to switch the sensitivity level, then release the buttons. Repeat to select another sensitivity level. You can select:
- A-0 Turns off the anti-collision function
- A-1 Sets the sensitivity to low
- A-2 Sets the sensitivity to medium
- A-3 Sets the sensitivity to high
The default setting is A2
Resetting the switch
- When the LED shows or , press and hold the (down) button until the tabletop reaches the lowest level and rebounds, then release the button. The LED shows the lowest position.
Clearing error codes
- If the LED shows error codes other than or and the (down) button doesn’t respond:
- Make sure that the power cord isn’t damaged, then unplug the cord from the outlet. Wait two minutes, then plug the cord back in. When the LED shows or , press and hold the (down) button to reset the switch.
- If the LED shows E01 or E02, unplug the cord from the outlet. Wait at least 18 minutes, then plug the cord back in and try again. When the LED shows or , press and hold the (down) button to reset the switch.
- If the LED still shows an error code, contact Customer Support.
Cleaning your desk
- Clean the surface of your desk with a duster or damp cloth only.
- Do not use abrasive cleaners.
Troubleshooting
Specifications
ONE-YEAR LIMITED WARRANTY
The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”). For this warranty to apply, your Product must be purchased in the United States or Canada from a Best Buy branded retail store or online at www.bestbuy.com or www.bestbuy.ca and is packaged with this warranty statement.
For product inquiries, please contact us with the information below: 1-877-467-4289 www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2022 Best Buy. All rights reserved
DOWNLOAD PDF LINK
