Onn 39900 Universal Remote User Manual

Onn 39900 Universal Remote User Manual

Battery Installation

Your universal remote requires two (2) AAA Alkaline batteries (not included).

To Install the Batteries:

1. Remove the battery compartment cover by sliding the cover down.
2. Match the (+) and (-) marks on the batteries to the (+) and (-) marks inside the battery compartment, then insert two (2) AAA Alkaline batteries. Be sure to use fresh batteries.
3. Slide the battery compartment cover back into place.

Battery Precautions:

• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
• Always remove old, weak or worn-out batteries promptly and recycle or dispose of them in accordance with local and national regulations.

Button Functions

• TV, CBL/SAT,VCR/AUX, DVD: Selects the device to control.
• ON/OFF: Turns the device On or Off.
• Red Indicator Light when any button is pressed.
• EXIT: Exits On- Screen Menus.
• MUTE: Turns off the TV sound while the picture remains. In SHIFT mode OK Selects menu items for the device you are controlling.
• INPUT: Selects the video inputs from available viewing sources.
• NUMBERS: Enter numbers for direct channel selection.
• DOT: Used to select digital channels
• RECORD, PLAY STOP, REW (rewind), FF (fast forward), PAUSE

• ? (INFO): displays/selects on-screen channel information, etc.
• MENU: displays the Menu on the TV and other devices. Use the SHIFT button to access this feature.
• VOLUME UP/DOWN: Changes the volume level of the device, normally the TV.
• CHANNEL Up/Down: Changes the channels. In SHIFT mode, these buttons navigate onscreen cursors and are used to make selections.
• SETUP: button is used to program the remote.
• SHIFT: is the alternative function of this button. Use the SHIFT button to access the Menu and Navigation functions of your device. To enter the SHIFT mode press this button once. To exit the shift mode, press the SHIFT button again.
• ENTER: For some TV models, used after direct channel number entry to immediately change to the selected channel.

Master Volume Feature

The Master Volume Feature allows you to select a single device (TV or audio receiver) that the volume control always controls. For example, the remote can be in TV mode while the volume buttons control the volume on your audio receiver instead of your TV.

1. Enabling the Master Volume Feature
   Press and hold the SETUP button until the red indicator stays on (approximately 4 seconds) and then release the button.
2. Press and release desired device button (TV, DVD, SAT, AUX) for the device you wish to setup to control the volume.
3. Press and release the MUTE button.
4. Press and release the VOL + button. The red indicator will blink twice and then go off.

Disabling the Master Volume Feature

1. Press and hold the SETUP button until the red indicator stays on (approximately 4 seconds) and then release the button.
2. Press and release the device button (TV, DVD, SAT, AUX) which is programmed to control the Master Volume Feature.
3. Press and release the MUTE button.
4. Press and release the VOL – button. The red indicator light will blink twice and go off.

Reset to Factory Settings

1. Press and hold the SETUP button until the red indicator stays on (approximately 4 seconds) and then release the button.
2. Press and release the OK button.
3. Press and release the number #0 button. The red indicator light will flash twice.

Care and Maintenance

• Keep the remote away from moisture. If it gets wet, dry it immediately.
• Use and store the remote at normal household temperatures.
• Use a soft, damp cloth to clean the remote.
• If the remote is not going to be used for a long period of time, remove the batteries from the remote.
• Handle the remote with care.

Troubleshooting

Remote does not operate your device.

• Make sure the batteries are fresh and installed correctly.
• Aim the remote directly at your device, and make sure that there are no obstructions between the remote and device.
• Make sure you select the appropriate device on the remote you wish to control, for example, TV for TV, DVD for DVD, etc.
• Try programming the remote with a different code. See Direct Code Entry section.
• Remote may not be compatible with your device.

Remote does not operate some features of your device.

• Sometimes a particular code might operate a few features but not all. Try programming remote with a different code from the code list. See Direct Code Entry section.
• Remote may not be able to operate all features of your device or button names may be different than that of your original remotes.

FAQS

How do you use a universal remote for the first time?

• This. So to see if the programming is. Right. You point the remote at the TV push the power button and it turns off which means it took the programming.

How do I change the input on my ONN TV without the remote?

• 2 three the AV component. If you want to watch live TV. And home if you want to get back on this home screen to select one of these. Options. You just have to release the button. Once it’s selected.