Panasonic CR2756-RG10(D2S) Remote Controller User Manual

Panasonic CR2756-RG10(D2S) Remote Controller User Manual

Remote Controller Specifications

NOTE:
For models of RG10Y1 (D2)/BGEF, and RG10Y2(D2S)/BGEF, If the unit is turned off under COOL, AUTO, or DRY mode with the set temperature less than 24 C, the set temperature will be automatically set to 24 C when you turn on the unit again. If the unit is turned off under HEAT mode with a set temperature of more than 24 C, the set temperature will be automatically set to 24 C when you turn on the unit again.

Quick Start Guide

NOT SURE WHAT A FUNCTION DOES?
Refer to the How to Use Basic Functions and How to Use Advanced Functions sections of this manual for a detailed description of how to use your air conditioner.

SPECIAL NOTE

• Button designs on your unit may differ slightly from the example shown.
• If the indoor unit does not have a particular function, pressing that function’s button on the remote control will have no effect. There are wide differences between “Remote controller Manual” and “USER’S
• MANUAL” on function description, the description of “USER’S MANUAL” shall prevail.

Handling the Remote Controller

Inserting and Replacing Batteries
Your air conditioning unit may come with two batteries(some units). Put the batteries in the remote control before use.

1. Slide the back cover from the remote control downward, exposing the battery compartment.
2. Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
3. Slide the battery cover back into place.

BATTERY NOTES
For optimum product performance:

• Do not mix old and new batteries or batteries of different types.
• Do not leave batteries in the remote control if you don’t plan on using the device for more than 2 months.

TIPS FOR USING REMOTE CONTROL

• The remote control must be used within 8 meters of the unit.
• The unit will beep when a remote signal is received.
• Curtains, other materials, and direct sunlight can interfere with the infrared signal receiver. Remove batteries if the remote will not be used for more than 2 months.

NOTES FOR USING REMOTE CONTROL

The device could comply with local and national regulations.

• In Canada, it should comply with CAN ICES-3(B)/NMB-3(B).
• In the USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Changes or modifications not approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Buttons and Functions

Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual.

Model:

• RG10A2(D2S)/BGEFU1,RG10Y2(D2S)/BGEF
• RG10A10(D2S)/BGEF(20-28 C/68-82 F)
• RG10A(D2S)/BGEF & RG10A(D2S)/BGEFU1(Fresh feature is not available)
• RG10A2(D2S)/BGCEFU1 & RG10A2(D2S)/BGCEF (Cooling-only models, AUTO mode, and HEAT mode are not available)

Model:

• RG10A1(D2S)/BGEF

• RG10B(D2)/BGEF(Fresh feature is not available)
• RG10B10(D2)/BGEF & RG10B10(D2)/BGCEF(20-28 C/68-82 F)
• RG10B2(D2)/BGCEF & RG10B10(D2)/BGCEF (Cooling only model
• AUTO mode and HEAT mode are not available )
• RG10Y1(D2)/BGEF

• RG10B1(D2)/BGEF

Remote Screen Indicators

Information is displayed when the remote controller is powered up.

Note:
All indicators shown in the figure are for the purpose of clear presentation. However, during the actual operation, only the relative function signs are shown on the display window.

How to Use Basic Functions

ATTENTION
Before the operation, please ensure the unit is plugged in and power is available.

AUTO Mode 

NOTE:

1. In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT function based on the set temperature.
2. In AUTO mode, the fan speed can not be set.

COOL or HEAT Mode

NOTE:
In DRY mode, fan speed can not be set since it has already been automatically controlled.

Setting the TIMER

ON/OFF – Set the amount of time after which the unit will automatically turn on/off.

TIMER ON setting

TIMER OFF setting

NOTE:

1. When setting the TIMER ON or TIMER OFF, the time will increase by 30-minute increments with each press, up to 10 hours. After 10 hours and up to 24, it will increase in 1-hour increments. (For example, press 5 times to get 2.5h, and press 10 times to get 5h,) The timer will revert to 0.0 after 24.
2. Cancel either function by setting its timer to 0.0h.

ECO operation: 
Under cooling mode, press this button, and the remote controller will adjust the temperature automatically to 24 C/75 F, fan speed of Auto to save energy (only when the set temperature is less than 24 C/75 F). If the set temperature is above 24 C/75 F, press the ECO button, the fan speed will change to Auto, and the set temperature will remain unchanged.

NOTE:
Pressing the ECO/GEAR button, or modifying the mode, or adjusting the set temperature to less than 24 C/75 F will stop ECO operation. Under ECO operation, the set temperature should be 24 C/75 F or above, it may result in insufficient cooling. If you feel uncomfortable, just press the ECO button again to stop it.

SHORTCUT function
Press the SHORTCUT button(some units) Push this button when remote controller is on, the system will automatically revert back to the previous settings including operating mode, setting temperature, fan speed level and sleep feature (if activated). If pushing more than 2 seconds, the system will automatically restore the current operation settings including operating mode, setting temperature, fan speed level, and sleep feature (if activated ).

The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details.

REFERENCE LINK

https://na.panasonic.com/ca/sites/default/files/2023-06/Remote_Controller_Manual_en.pdf